Photodiode read-out of the ALICE photon spectrometer PbWO4PbWO_{4} crystals

Proposal of abstract for LEB99, Snowmass, Colorado, 20-24 September 1999The PHOton Spectrometer of the ALICE experiment is an electromagnetic calorimeter of high granularity consisting of 17280 lead-tungstate (PWO) crystals of dimensions 22x22x180 mm3, read out by large-area PIN-diodes with very low-noise front-end electronics. The crystal assembly is operated at -25C to increase the PWO light yield. A 16.1x17.1 mm2 photodiode, optimized for the PWO emissio spectrum at 400-500 nm, has been developed. The 20x20 mm2 preamplifier PCB is attached to the back side of the diode ceramic frame. The charge sensitive preamplifier is built in discrete logic with two input JFETs for optimum matching with the ~150pF PIN-diode. A prototype shaper has been designed and built in discrete logic. For a detector matrix of 64 units the measured ENCs are between 450-550e at -25C. Beam tests demonstrate that the required energy resolution is reached.Summary:The PHOton Spectrometer of the ALICE experiment is an electromagnetic calorimeter of high granularity consisting of 17280 lead-tungstate (PWO) crystals of dimensions 22x22x180 mm3, coupled to large-area PIN-diodes with matching low-noise preamplifiers. PHOS is optimized for measuring photons, pi0s and eta mesons in the momentum ranges 0.5-10, 1-10 and 2-10 GeV/c, respectively, and is designed for the expected large number of particles that will be produced in central Pb-Pb collisions. Lead tungstate (PWO) is a fast scintillating crystal with a rather complex emission spectrum, consisting of two components: a blue component peaking at 420 nm and a green component peaking at 480-520 nm. The light yield of PWO at room temperature is low compared with other heavy scintillating crystals, for instance BGO. However, the yield depends strongly on the temperature with a coefficient of ~-2 degree. At the selected operating temperature of -25C the yield is about a factor of 3 higher compared to room temperature. Still, in order to reach the required energy resolution for a PHOS channel, an ENC noise of less than 600e for the PIN-diode-preamplifier-shaper stage is required. This is a very low value taking into account the high capacitance of 150-200 pF of the large area PIN-diodes. In collaboration with the PHOS project, the company AME (Horten, Norway) has designed and produced a PIN-photodiode optimized for the cross-section and spectral responsivity of the PHOS PWO crystal. The photodiode has an active area of 17.1x16.1 mm2 and is fabricated on n-type silicon material of thickness 280 um. The wafer specific resistivity is between 3000 and 6000 ohm-cm, which corresponds to a depletion voltage of 70V. The photodiode response is optimized for the spectral region 400-500 nm in order to match the PWO emission spectrum. The PIN-diode is mounted on a ceramic substrate 0.65 mm thick. On this substrate the diode is surrounded by a ceramic frame. The preamplifier PCB of dimension 20x20 mm2 is attached to the back side of the frame. The PIN-diode and bondings to ground and preamplifier input are protected by an optically transparent epoxy layer. The front side of the PIN-diode is glued onto the endface of the PWO crystal with optically transparent glue (Melt-Mount Quick-Stick, Cargille Laboratories, USA). Each crystal is wrapped in White Tyvek to ensure maximum light collection efficiency and optical insulation between the crystals. The PHOS detector consists of four independent modules, each with 4320 channels. The crystal assembly with the photo detectors are operated at -25 +/- 0.3C. The power dissipation per module is ~1 kW. The charge sensitive preamplifier is an operational amplifier built in discrete logic and with two input JFETs (BF861A). Using two JFETs in parallel gives the lowest noise for detector capacitance >100 pF. A prototype shaper, comprising three amplification stages, has been designed and built in discrete logic. For a PIN-diode with capacitance ~150 pF and a leakage current <1 nA under cooling, calculations give optimum time differentiation and integration constants around 3 microsec. For a detector matrix of 64 units the measured ENCs are between 450-550 e at -25C. Beam tests of this matrix show that the required energy resolution for the PHOS is reached

Solution g6n6rale des 6quations diff6rentieles fonda-mentales d'61asticit6, exprim6e par trois fonctions harmoniques

to arbitrary pairs of elastic materials occupying the two bonded half-spaces, including the case when the second material has vanishing elastic moduli, i.e., inclusion in a half-space. The results obtained in the paper by Yu and Sanday (1990) form a subset of the present solution. The advantage of the Papkovich potential notation fbr the representation of elastic fields is not confined to the ease of derivation of new solutions. The final results for axisymmetric inclusions in one of two dissimilar elastic half-spaces were kept in this form in the previous section quite deliberately. From the practical viewpoint, the application of the solutions presented in this paper is likely to involve computer coding of the formulae. The concise potential form of the solutions allows the final stress and displacement formulae to be rederived and verified as many times as necessary using well established recipes, which in this case are given by Eqs

Charged Particle Veto Detector for the PHOS Spectrometer

The general design of the Charged Particle Veto (CPV) detector for the photon spectrometer (PHOS) of the ALICE experiment along with beam test results of the CPV prototype in 1998 are presented

Charged Particle Veto Detector with Open Geometry for the PHOS Spectrometer

Abstract Abstract &nbsp; The Charged Particle Veto (CPV) detector with open geometry for the photon spectrometer (PHOS) of the ALICE experiment together with beam test results of the CPV prototype in 1999 are presented. </HTML