29 research outputs found
Using Molecules to Measure Nuclear Spin-Dependent Parity Violation
Nuclear spin-dependent parity violation arises from weak interactions between
electrons and nucleons, and from nuclear anapole moments. We outline a method
to measure such effects, using a Stark-interference technique to determine the
mixing between opposite-parity rotational/hyperfine levels of ground-state
molecules. The technique is applicable to nuclei over a wide range of atomic
number, in diatomic species that are theoretically tractable for
interpretation. This should provide data on anapole moments of many nuclei, and
on previously unmeasured neutral weak couplings
Recommended from our members
Optical Coatings for Thermophotovoltaic Spectral Control
The efficiency of thermophotovoltaic (TPV) energy conversion is dependent on efficient spectral control. An edge pass filter (short pass) in series with a highly doped, epitaxially grown layer has achieved the highest performance of TPV spectral control. Front surface, tandem filters have achieved the highest spectral efficiency and represent the best prospect for even higher spectral efficiency for TPV energy conversion systems. Specifically, improvements in the physical vapor deposition process, identification of other materials with a high index of refraction and a low absorption coefficient, and more efficient edge filter designs could provide higher TPV spectral performance
Recommended from our members
Front Surface Spectral Control Development for TPV Energy Conversion (a Presentation)
This paper discusses the introduction to the potential of alternative materials that provide higher temperature stability than current materials. The outline of this report is: (1) Review briefly the importance of spectral control; (2) Provide current results; (3) Introduce the temperature stability issue; (4) Describe the requirements for alternate materials and (5) Present alternative materials. The conclusions of this report are: (1) Antimony selenide has achieved the highest spectral efficiency to date; (2) Several materials expected to have higher temperature stability have been shown to be viable; (3) So far, with limited development, the performance of the these materials is lower than Antimony selenide; and (4) Additional development will be required to achieve similar or higher performance
Recommended from our members
The Status of Thermophotovoltaic Energy Conversion Technology at Lockheed Martin Corporation
In a thermophotovoltaic (TPV) energy conversion system, a heated surface radiates in the mid-infrared range onto photocells which are sensitive at these energies. Part of the absorbed energy is converted into electric output. Conversion efficiency is maximized by reducing the absorption of non-convertible energy with some form of spectral control. In a TPV system, many technology options exist. Our development efforts have concentrated on flat-plate geometries with greybody radiators, front surface tandem filters and a multi-chip module (MCM) approach that allows selective fabrication processes to match cell performance. Recently, we discontinued development of GaInAsSb quaternary cell semiconductor material in favor of ternary GaInAs material. In our last publication (Ref. 1), the authors reported conversion efficiencies of about 20% (radiator 950 C, cells 22 C) for small modules (1-4 cm{sup 2}) tested in a prototypic cavity test environment. Recently, we have achieved measured conversion efficiencies of about 12.5% in larger ({approx}100 cm{sup 2}) test arrays. The efficiency reduction in the larger arrays was probably due to quality and variation of the cells as well as non-uniform illumination from the hot radiator to the cold plate. Modules in these tests used GaInAsSb cells with 0.52 eV bandgap and front surface filters for spectral control. This paper provides details of the individual system components and the rationale for our technical decisions. It also describes the measurement techniques used to record these efficiencies
Recommended from our members
The Status of Thermophotovoltaic Energy Conversion Technology at Lockheed Martin Corp.
In a thermophotovoltaic (TPV) energy conversion system, a heated surface radiates in the mid-infrared range onto photodiodes which are sensitive at these energies. Part of the absorbed energy is converted into electric output. Conversion efficiency is maximized by reducing the absorption of non-convertible energy with some form of spectral control. In a TPV system, many technology options exist. The development efforts have concentrated on flat-plate geometries with greybody radiators, low bandgap quaternary diodes, front surface tandem filters and a multi-chip module (MCM) approach that allows selective fabrication processes to match diode performance. Recently, the authors achieved conversion efficiencies of about 20% (radiator 950 C, diodes 22 C) for a module in a prototypic cavity test environment. These tests employed InGaAsSb diodes with 0.52 eV bandgap and front surface filters for spectral control. This paper provides details of the individual system components and describes the measurement technique used to record these efficiencies
Recommended from our members
New Performance Levels for TPV Front Surface Filters
Front surface spectral control filters significantly improve the efficiency of thermophotovoltaic (TPV) converters. Tandem filter designs for 0.52 and 0.60 eV cells were fabricated. Energy and angle weighted spectral efficiencies of {approx}83% for the 0.52 eV application and {approx}76% for the 0.60 eV applications were achieved with {approx}78% angle weighted above bandgap transmission. Manufacturing demonstrations of both designs were completed with good yield. Design improvements were made using angle weighted spectral utilization and above bandgap transmission as refinement goals. Current development work addresses elimination of the plasma filter and alternate substrates