Medium energy proton radiation damage to (AlGa)As-GaAs solar cells

The performance of (AlGa)As-GaAs solar cells irradiated by medium energy 2, 5, and 10 MeV protons was evaluated. The Si cells without coverglass and a number of GaAs solar cells with 12 mil coverglass were irradiated simultaneously with bare GaAs cells. The cell degradation is directly related to the penetration of depth of protons with GaAs. The influence of periodic and continuous thermal annealing on the GaAs solar cells was investigated

GaAs solar cells for concentrator systems in space

Cells for operation in space up to more than 100 suns were made, and an AMO efficiency of 21% at 100 suns with these cells was obtained. The increased efficiency resulted not only from the higher open circuit voltage associated with the higher light intensity (higher short circuit current); it also benefitted from the increase in fill factor caused by the lower relative contribution of the generation recombination current to the forward bias current when the cell's operating current density is increased. The experimental cells exhibited an AMO efficiency close to 16% at 200 C. The prospect of exploiting this capability for the continuous annealing of radiation damage or for high temperature missions (e.g., near Sun missions) remains therefore open. Space systems with concentration ratios on the order of 100 suns are presently under development. The tradeoff between increased concentration ratio and increased loss due to the cell's series resistance remains attractive even for space applications at a solar concentrator ratio of 100 suns. In the design of contact configuration with low enough series resistance for such solar concentration ratios, the shallow junction depth needed for good radiation hardness and the thin AlGaAs layer thickness needed to avoid excessive optical absorption losses have to be retained

Test-bed development & measurement plan for evaluating transmit diversity in DVB networks

This paper presents a test-bed development and measurement plan for evaluating transmit diversity in the DVB network. Transmit diversity reduces the complexity and improves the power consumption of the personal receiving devices by improving the transmission of signals in NLOS cluttered environments. Also, it is more practical than receive diversity due to the difficulty of locating two receive antennas far enough apart in a small mobile device. Test service scenarios were developed to illustrate the benefits of such technologies so that effectiveness can be researched in a variety of service and terrain scenarios using purpose built test systems. The laboratory tests were designed to validate the theoretical measurements from the theoretical analysis and these results will be verified by a field measurement campaign in short and long time spans

Germanium-on-silicon mid-infrared waveguides and Mach-Zehnder interferometers

In this paper we describe Ge-on-Si waveguides and Mach-Zehnder interferometers operating in the 5.2 - 5.4 mu m wavelength range. 3dB/cm waveguide losses and Mach-Zehnder interferometers with 20dB extinction ratio are presented

Measurements, processing functions and laboratory test-bed experiments for evaluating diversity in broadcast network

This paper presents a test-bed development and measurement plan for evaluating transmit diversity and on-channel repeaters in the Digital Video Broadcasting Network. Transmit diversity reduces the complexity and improves the power consumption of the personal receiving devices by enhancing the transmission of signals in NLOS cluttered environments. It is more practical than receive diversity due to the difficulty of locating two receive antennas far enough apart in a small mobile device. The on-channel repeater is to extend the coverage of the DVB-T/H network in areas where services are inaccessible by receiving the DVB-T/H signals off air, amplifying and then retransmitting it on the same frequency as received. Test service scenarios were developed to illustrate the benefits of such technologies so that effectiveness can be researched in a variety of service and terrain scenarios using purpose built test systems.The work presented in this paper was supported by the European Commission IST project PLUTO

Laboratory measurement campaign of DVB-T signal with transmit delay diversity

The requirements for future DVB-T/H networks demand that broadcasters design and deploy networks that provide ubiquitous reception in challenging indoors and other obstructed situations. It is essential that such networks are designed cost-effectively and with minimized environmental impact. The EC funded project PLUTO has since its start in 2006 explored the use of diversity to improve coverage in these difficult situations. The purpose of this paper is to investigate the performance of Transmit Delay Diversity (DD) with two antennas to improve the reception of DVB-T/H systems operating in different realistic propagation conditions through a series of tests using a SPIRENT SR5500 dual channel emulator. The relationship between correlation coefficient between channels, receiver velocity and diversity gain is nvestigated. It is shown that transmit delay diversity significantly improves the quality of reception particularly in simulated fast fading mobile broadcasting applications. This paper documents research conducted by Brunel University and Broadreach Systems

Processing of strong flux trapping high T(subc) oxide superconductors: Center director's discretionary fund

Magnetic suspension effect was first observed in samples of YBa2Cu3O7/AgO(Y-123/AgO) composites. Magnetization measurements of these samples show a much larger hysteresis which corresponds to a large critical current density. In addition to the Y-123AgO composites, recently similar suspension effects in other RE-123/AgO, where RE stands for rare-Earth elements, were also observed. Some samples exhibit even stronger flux pinning than that of the Y-123/AgO sample. An interesting observation was that in order to form the composite which exhibits strong flux trapping effect the sintering temperature depends on the particular RE-123 compound used. The paper presents the detailed processing conditions for the formation of these RE-123/AgO composites, as well as the magnetization and critical field data

Stress Distribution in Mandible Regulated by Bone and Dental Implant Parameters: Part I - Methodology

The complicated inter-relationships between mandibular bone components and dental implants have attracted the attention of many a structural mechanics researcher as well as many a dental practitioner. This paper describes the methodology and analysis techniques employed to enable accurate evaluation of a vast range of the implant and bone parameters. The complex material and geometric properties of the bone and implant are modelled using two-dimensional (2D) triangular and quadrilateral plane strain elements. Assumptions made in the analysis include: (a) 50% osseointegration between bone and implant; (b) linear relationships exist between the stress value and the Young’s moduli of the cancellous and cortical bone at any specific point. In the companion paper (Part II) various bone, implant and loading parameters are evaluated for their influence on the stress distribution within the bone, in particular in the mandible