251 research outputs found
Influence of atomic mixing and preferential sputtering on depth profiles and interfaces
Atomic mixing and preferential sputtering impose a depth resolution limit on the use of sputter sectioning to measure the composition of metalâsemiconductor interfaces. Experimental evidence obtained with the PtâSi system is used to demonstrate ionâinduced atomic mixing and then its effect on sputter etching and depth profiling. Starting with discrete layer structures, a relatively low ion dose (âł3Ă10^(15) cm^(â2)) first produced a mixed surface layer with thickness comparable to the ion range. Higher ion doses then result in successive sputter etching and continual atomic mixing over a constant surface layer thickness. A model is developed that is based on a sputter removal (including preferential sputtering) of atoms at the surface and a uniform mixing of atoms over a constant thickness. The model predicts the influences of atomic mixing and preferential sputtering on the depth profiling of thinâfilm structures and interfaces
Dissociation mechanism for solid-phase epitaxy of silicon in the Si <100>/Pd2Si/Si (amorphous) system
Solid-phase epitaxial growth (SPEG) of silicon was investigated by a tracer technique using radioactive 31Si formed by neutron activation in a nuclear reactor. After depositing Pd and Si onto activated single-crystal silicon substrates, Pd2Si was formed with about equal amounts of radioactive and nonradioactive Si during heating at 400 °C for 5 min. After an 1-sec annealing stage (450-->500 °C in 1 h) this silicide layer, which moves to the top of the sample during SPEG, is etched off with aqua regia. From the absence of radioactive 31Si in the etch, it is concluded that SPEG takes place by a dissociation mechanism rather than by diffusion
Heterostructure by solidâphase epitaxy in the Siă111ă/Pd/Si (amorphous) system
When a thin film of Pd reacts with a ă111ă Si substrate, a layer of epitaxial Pd_2Si is formed. It is shown that Si can grow epitaxially on such a layer by solidâphase reaction
Depth dependence of atomic mixing by ion beams
Ion backscattering spectrometry has been used to investigate the depth dependence of atomic mixing induced by ion beams. Samples consisting of a thin Pt (or Si) marker a few tens of angstroms thick buried at different depths in a deposited Si (or Pt) layer were bombarded with Xe+ of 300 keV at 2Ă10^16 cm^â2 dose and Ar+ of 150 keV at 5Ă10^15cm^â2 dose. Significant spreading of the marker was observed as a result of ion irradiation. The amount of spreading was measured as a function of depth of the marker, which was then compared with the deposited energy distribution. Measurements of this kind promise new insight into the nature of the interaction between ion beams and solids
Growth mechanism for solid-phase epitaxy of Si in the Si <100>/Pd2Si/Si(amorphous) system studied by a radioactive tracer technique
A tracer technique using radioactive 31Si (T1/2=2.62 h) was used to study solid-phase epitaxial growth (SPEG) of silicon. After depositing Pd and Si onto single-crystal substrates which had been activated in a nuclear reactor, Pd2Si was formed with about equal amounts of radioactive and nonradioactive silicon during heating at 400 °C for 5 min. After a second annealing stage (450 °C-->500 °C in 1 h) the silicide layer which moves to the top of the sample during SPEG was etched off with aqua regia. From the absence of radioactive 31Si in the etchant solution it is concluded that SPEG takes place by dissociation of the Pd2Si layer at the single-crystal interface to provide free Si for epitaxial growth, while new silicide is formed at the interface with the amorphous Si. These results were confirmed by evaporating radioactive silicon onto nonactivated silicon substrates before evaporation of Pd and stable amorphous Si and by measuring the activity in the SPEG sample before and after etching off the silicide layer
Limits of composition achievable by ion implantation
In highâdose ion implantation for materials modification, the maximum concentration of the implanted species is determined by ionâinduced erosion (sputtering) of the implanted layer. In this review, we consider the influence of preferential sputtering and atomic mixing. The maximum concentration of the implanted species is given roughly by r/S and extends over a depth W where S is the sputtering yield, r is the preferential sputtering factor (1/2âČrâČ2) and W is a depth comparable to the ion range. Good agreement between calculation and experiment is found for 150âkeV Au implanted into Cu or Fe. Surface conditions, such as oxide layers or carbon films, can alter sputtering yields and can lead to the mixing of surface contaminants throughout the implanted layer. Implantation of species A into a target material AB results in a different concentration limit, but again preferential sputtering and the total sputtering yield set this limit. Calculations for PtSi indicate that the concentration of Si is decreased by implantation of Si for Sâł3
Antimony doping of Si layers grown by solid-phase epitaxy
We report here that layers of Si formed by solid-phase epitaxial growth (SPEG) can be doped intentionally. The sample consists initially of an upper layer of amorphous Si (~1 ”m thick), a very thin intermediate layer of Sb (nominally 5 Ă
), and a thin lower layer of Pd (~500 Ă
), all electron-gun deposited on top of a single-crystal substrate (1â10 Ω cm, p type, orientation). After a heating cycle which induces epitaxial growth, electrically active Sb atoms are incorporated into the SPEG layer, as shown by the following facts: (a) the SPEG layer forms a p-n junction against the p-type substrate, (b) the Hall effect indicates strong n-type conduction of the layer, and (c) Auger electron spectra reveal the presence of Sb in the layer
- âŠ