Eta electroproduction on nuclei in the nucleon resonance region

We investigate eta electroproduction on nuclei for Q^2=2.4 and 3.6 GeV^2 in the framework of a coupled-channel BUU transport model. We analyze the importance of final state interactions and side feeding and compare with findings drawn from eta photoproduction. It is shown that in contrast to photoproduction the influence of etas stemming from secondary processes becomes important at high Q^2.Comment: 5 pages, 5 figure

Influence of the nucleon spectral function in photon and electron induced reactions on nuclei

We study the influence of the nucleon spectral function on eta photo- and electroproduction on nuclei. Besides kinematical effects due to groundstate correlations, also a modification of the S11(1535) decay width is taken into account, which is caused by the possible decay into nucleons with mass smaller than the pole mass in the medium. Hence, resonances with masses below the free N eta threshold can contribute to eta production.Comment: 13 pages, 8 figure

In-medium broadening of nucleon resonances

We analyze the effects of an in-medium broadening of nucleon resonances on the exclusive photoproduction of mesons on nuclei as well as on the total photoabsorption cross sections in a transport calculation. We show that the resonance widths observed in semi-inclusive photoproduction on nuclei are insensitive to an in-medium broadening of nucleon resonances. This is due to a simple effect: the sizeable width of the nuclear surface and Fermi motion.Comment: 4 pages, 3 figures, minor changes in the tex

Factors affecting the operation of laser-triggered gas switch (LTGS) with multi-electrode spark gap

Multi-electrode spark switches can be used for switching applications at elevated voltages or for command triggering. Symmetrical field graded electrodes allow the electrical stress across individual gaps to be controlled, thus maximising the hold off voltage and reducing switch pre-fire. The paper considers some aspects of multielectrode switch design and their influence on switching behavior. Non-symmetrical, uni-directional electrode topologies can be employed with advantages over traditional symmetrical design. The choice of working gas and gas pressure can influence switching performance in terms of delay-time and jitter. Transient analysis of switch characteristics has been undertaken in order to understand multi-electrode switching

The triggered behavior of a controlled corona stabilised cascade switch

Corona stabilised switches have been shown to have advantages in pulse power switching applications due to their high repetition rates and low jitter. Work performed in recent years by the High Voltage Technologies Group within the Department of Electronic and Electrical Engineering at the University of Strathclyde has shown that the operating voltage range of such switches can be extended by using a multi-gap cascade configuration. One particular multi-gap topology was shown to operate under pressure at 100 kV with a switching jitter of 2ns. It has since been shown that by modifying the topology of the corona sources on the electrodes, it is possible to control the grading of the voltage distribution across the gaps in the cascade. The voltages across each gap and the self-break behaviour of the cascade were found to be in close agreement with the values predicted from the corona emission characteristics for the tested electrode topologies. This paper reports on a further examination of the behaviour of the corona controlled switching topology, where triggered operation of the switch has been investigated for different voltage distributions across the cascade gaps

Surface flashover of oil-immersed dielectric materials in uniform and non-uniform fields

The applied electrical fields required to initiate surface flashover of different types of dielectric material immersed in insulating oil have been investigated, by applying impulses of increasing peak voltage until surface flashover occurred. The behavior of the materials in repeatedly over-volted gaps was also analyzed in terms of breakdown mode (some bulk sample breakdown behaviour was witnessed in this regime), time to breakdown, and breakdown voltage. Cylindrical samples of polypropylene, low-density polyethylene, ultra-high molecular weight polyethylene, and Rexolite, were held between two electrodes immersed in insulating oil, and subjected to average applied electrical fields up to 870 kV/cm. Tests were performed in both uniform- and non-uniform-fields, and with different sample topologies. In applied field measurements, polypropylene required the highest levels of average applied field to initiate flashover in all electrode configurations tested, settling at similar to 600 kV/cm in uniform fields, and similar to 325 kV/cm in non-uniform fields. In over-volted point-plane gaps, ultra-high molecular weight polyethylene exhibited the longest pre-breakdown delay times. The results will provide comparative data for system designers for the appropriate choice of dielectric materials to act as insulators for high-voltage, pulsed-power machines