The ABC130 barrel module prototyping programme for the ATLAS strip tracker

For the Phase-II Upgrade of the ATLAS Detector, its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100 % silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-25) and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests.Comment: 82 pages, 66 figure

Measuring the borders of the active area on silicon strip sensors

Silicon strip sensors for the ATLAS Inner Tracker (ITk) have been designed to provide reliable particle detection in the high-radiation environment of the High-Luminosity Large Hadron Collider. One important design criterion for their development is the minimisation of inactive sensor area (bias ring, guard ring and edge implant surrounding the active sensor area), as inactive sensor areas impact the hermeticity of particle detection inside the detector. In previous measurements of ATLAS silicon strip sensors, the charge collecting area of individual strip implants has been mapped and found to agree well with the sensor strip pitch and strip length. For strip implants next to the sensor bias ring, the extent of their charge collecting area towards the inactive sensor area was previously unknown, which limited the accuracy of both overall detector hermeticity estimates and the position resolution for particle detection at the sensor edge. Therefore, measurements were conducted to map the area of charge collection for sensor strips at the edge of the active sensor area. Using a micro-focused X-ray beam has made it possible to map this shape both within the sensor plane as well as inside the sensor volume. This contribution presents measurements showing the extent of charge collection in the edge strips (with a condition where the AC metal of a strip between the bias ring and the edge strips is being floated) of silicon strip sensors. The edge regions of two generations of ITk strip sensor modules were studied: one module with a short strip (ATLAS12) sensor and ABC130 readout chips and one module a long strip (ATLAS17LS) sensor and ABCstar readout chips

Mapping the in-plane electric field inside irradiated diodes

A significant aspect of the Phase-II Upgrade of the ATLAS detector is the replacement of the current Inner Detector with the ATLAS Inner Tracker (ITk). The ATLAS ITk is an all-silicon detector consisting of a pixel tracker and a strip tracker. Sensors for the ITk strip tracker have been developed to withstand the high radiation environment in the ATLAS detector after the High Luminosity Upgrade of the Large Hadron Collider at CERN, which will significantly increase the rate of particle collisions and resulting particle tracks. During their operation in the ATLAS detector, sensors for the ITk strip tracker are expected to accumulate fluences up to $1.5\cdot10^{15}\,\text{n}_{\text{eq}}/\text{cm}^2$ (including a safety factor of 1.5), which will significantly affect their performance. One characteristic of interest for highly irradiated sensors is the shape and homogeneity of the electric field inside its active area. For the results presented here, diodes with edge structures similar to full size ATLAS sensors were irradiated up to fluences comparable to those in the ATLAS ITk strip tracker and their electric fields mapped using a micro-focused X-ray beam (beam diameter $2\times3$ $\mu$m). This contribution shows the extension and shape of the electric field inside highly irradiated diodes over a range of applied bias voltages. Additionally, measurements of the outline of the depleted sensor areas allow a comparison of the measured leakage current for different fluences with expectations for the corresponding active areas

The ABC130 barrel module prototyping programme for the ATLAS strip tracker

For the Phase-II Upgrade of the ATLAS Detector [1], its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100% silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-250) [2,2] and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests