78 research outputs found
Distribution of 137Cs in benthic plants along depth profiles in the outer Puck Bay (Baltic Sea)
In-situ upgrading of Napier grass pyrolysis vapour over microporous and hierarchical mesoporous zeolites
This study presents in-situ upgrading of pyrolysis
vapour derived from Napier grass over microporous and
mesoporous ZSM-5 catalysts. It evaluates effect of process
variables such catalyst–biomass ratio and catalyst type in
a vertical fixed bed pyrolysis system at 600 °C, 50 °C/min
under 5 L/min nitrogen flow. Increasing catalyst–biomass
ratio during the catalytic process with microporous structure
reduced production of organic phase bio-oil by approximately
7.0 wt%. Using mesoporous catalyst promoted
nearly 4.0 wt% higher organic yield relative to microporous
catalyst, which translate to only about 3.0 wt% reduction
in organic phase compared to the yield of organic phase
from non-catalytic process. GC–MS analysis of bio-oil
organic phase revealed maximum degree of deoxygenation
of about 36.9% with microporous catalyst compared to
the mesoporous catalysts, which had between 39 and 43%.
Mesoporous catalysts promoted production olefins and
alkanes, normal phenol, monoaromatic hydrocarbons while
microporous catalyst favoured the production of alkenes
and polyaromatic hydrocarbons. There was no significant increase in the production of normal phenols over microporous catalyst due to its inability to transform the methoxyphenols and methoxy aromatics. This study demonstrated that upgrading of Napier grass pyrolysis vapour over mesoporous ZSM-5 produced bio-oil with improved physicochemical properties
Fundamental characterisation of waste and biomass for char production
Conversion of industrial waste materials to valuable resources would essentially take part in an ecologically sustainable future. There are still large amounts of undervalued biomass wastes generated from a diverse range of industries that are disposed in landfields. They have potential to produce valuable materials and fuels, such as charcoal, bio-oils and bio-gas through termal upgrading. In order to enhance the efficiency of the thermal upgrading process, comprehensive characterisation of the raw biomass materials is essential. We have developed a novel thermal characterisation method that utilises computer aided thermal analysis incorporated with a gas analyser. The method was applied on two biomass materials, wood sawdust and bagasse. The paper discusses the results obtained with the novel thermal characterisation technique.4 page(s
Experimental and modelling of the thermal regions of activity during pyrolysis of bituminous coals
18 page(s
Technological advances of industrial biomass pyrolysis
Pyrolysis is the thermal process of decomposition of organic material under elevated temperatures and atmospheres of little or no oxygen, producing biogas, bio-oil and char. The growing interest in industrial biomass pyrolysis is the potential for upgrading of the pyrolysis bio-oils to liquid transport fuels, while the solid char, which is rich in carbon, can be used as a renewable solid fuel alternative, specialty carbon product, such as metallurgical carbon or can be blended into soils thereby sequestering carbon and improving soil quality. Industrial biomass pyrolysis processes can operate under fast or slow pyrolysis conditions, depending on the residence time and heating rate of the material in the reactor. Fast pyrolysis is characterised by rapid heating rates that are usually within the range of 1,000 to 10,000 °C/s. On a dry feed basis the yields of liquid oil from fast pyrolysis are between 50 and 80 wt% with gas and char products accounting for the remainder in approximately even proportions. Slow pyrolysis applies gradual heating rates that can be as low as several degrees per minute, where the products may range from being equally distributed amongst the solid, liquid and gas phases to producing solid and gas only. Fast pyrolysis reactor types include bubbling fluidized beds, circulating fluidized beds, rotating cone transported beds and ablative pyrolysers. Slow pyrolysis reactor designs include vacuum pyrolysers, bubbling fluidized beds, augers and heated kilns of various types. At present, most of the reactor designs have been scaled to either pilot or demonstration plant levels. The factors hindering further commercialization of biomass pyrolysis technologies are associated with the inherent limitations of the various reactors. These include raw material feed size and moisture requirements, energy efficiency, scalability restrictions, plant capital intensity and product quality. This chapter reviews and compares the strengths and weaknesses of each reactor design and elucidates the likely pathway for further development of low capital cost, scalable and energy efficient pyrolysis technology.30 page(s
- …