Enhancement of fracture toughness of epoxy nanocomposites by combining nanotubes and nanosheets as fillers

In this work the fracture toughness of epoxy resin has been improved through the addition of low loading of single part and hybrid nanofiller materials. Functionalised multi-walled carbon nanotubes (f-MWCNTs) was used as single filler, increased the critical strain energy release rate, GIC, by 57% compared to the neat epoxy, at only 0.1 wt% filler content. Importantly, no degradation in the tensile or thermal properties of the nanocomposite was observed compared to the neat epoxy. When two-dimensional boron nitride nanosheets (BNNS) were added along with the one-dimensional f-MWCNTs, the fracture toughness increased further to 71.6% higher than that of the neat epoxy. Interestingly, when functionalised graphene nanoplatelets (f-GNPs) and boron nitride nanotubes (BNNTs) were used as hybrid filler, the fracture toughness of neat epoxy is improved by 91.9%. In neither of these hybrid filler systems the tensile properties were degraded, but the thermal properties of the nanocomposites containing boron nitride materials deteriorated slightly

Improving the fracture toughness properties of epoxy using graphene nanoplatelets at low filler content

This paper reports improvement in the fracture properties of epoxy nanocomposites using plasma functionalized graphene nanoplatelets (f-GNP) at low filler content. Various mechanical tests were performed on a series of f-GNP/epoxy at low nanofiller loading to assess the effect of the nanofiller on mechanical properties. Most importantly, a significant enhancement in fracture toughness is achieved without compromising the tensile and thermal properties of the nanocomposites. The fracture toughness of neat epoxy resin was increased by over 50% with the incorporation of 0.25 wt% f-GNP loading, obtaining a value of 245 J m−2, while the neat epoxy indicated a value of 162 J m−2. The glass transition temperature (Tg) and coefficient of thermal expansion (CTE) both showed a slight increase of 3% and 2%, respectively, both at 1 wt% f-GNP loading. These enhancements are competitive with current literature results on nanocomposites, but at significantly lower filler content. We therefore demonstrate that f-GNPs are capable of providing effective toughening of epoxy resins, while maintaining other tensile and thermal properties

Ballistic impact behaviour of glass fibre reinforced polymer composite with 1D/2D nanomodified epoxy matrices

In this paper, experimental studies on the ballistic impact behaviour of nanomodified glass fibre-reinforced polymer (GFRP) are reported. The epoxy matrix of the GFRP was modified by the addition of graphene platelets (GNPs), carbon nanotubes (CNTs), combined hybrid hexagonal boron nitride nanosheets (BNNS)/CNT, and combined boron nitride nanotubes (BNNTs)/GNPs nanoparticles. Ballistic impact tests were carried out on GFRP laminates at two projectile velocities of 76 ± 1 m s−1 for full-field deformation measurements and 134.3 ± 1.7 m s−1 for perforation tests. The behaviour of the plates during impact was recorded using digital image correlation (DIC), in order to monitor strain and out-of-plane deformation in panels with nanoreinforced matrices. Following penetrative impact tests, pulse thermography was used to characterise the delamination of impacted plates. The results of full-field deformation, exit velocity and energy absorption measurements from the ballistic tests show significant improvements in impact resistance for the panels made from nanomodified epoxies relative to laminates with the unmodified epoxy matrix. The highest absolute absorbed energy was observed for the GFRP panels fabricated using the epoxy matrix loaded with BNNT/GNP at 255.7 J, 16.8% higher than the unmodified epoxy matrix

On the extent of fracture toughness transfer from 1D/2D nanomodified epoxy matrices to glass fibre composites

Abstract: In this study, the effects of adding nanofillers to an epoxy resin (EP) used as a matrix in glass fibre-reinforced plastic (GFRP) composites have been investigated. Both 1D and 2D nanofillers were used, specifically (1) carbon nanotubes (CNTs), (2) few-layer graphene nanoplatelets (GNPs), as well as hybrid combinations of (3) CNTs and boron nitride nanosheets, and (4) GNPs and boron nitride nanotubes (BNNTs). Tensile tests have shown improvements in the transverse stiffness normal to the fibre direction of up to about 25% for the GFRPs using the ‘EP + CNT’ and the ‘EP + BNNT + GNP’ matrices, compared to the composites with the unmodified epoxy (‘EP’). Mode I and mode II fracture toughness tests were conducted using double cantilever beam (DCB) and end-notched flexure (ENF) tests, respectively. In the quasi-static mode I tests, the values of the initiation interlaminar fracture toughness, GICC, of the GFRP composites showed that the transfer of matrix toughness to the corresponding GFRP composite is greatest for the GFRP composite with the GNPs in the matrix. Here, a coefficient of toughness transfer (CTT), defined as the ratio of mode I initiation interlaminar toughness for the composite to the bulk polymer matrix toughness, of 0.68 was recorded. The highest absolute values of the mode I interlaminar fracture toughness at crack initiation were achieved for the GFRP composites with the epoxy matrix modified with the hybrid combinations of nanofillers. The highest value of the CTT during steady-state crack propagation was ~ 2 for all the different types of GFRPs. Fractographic analysis of the composite surfaces from the DCB and ENF specimens showed that failure was by a combination of cohesive (through the matrix) and interfacial (along the fibre/matrix interface) modes, depending on the type of nanofillers used

Gas physisorption measurements as a quality control tool for the properties of graphene/graphite powders

The industrial-scale production and commercialisation of graphene and related 2D materials introduces the need for rapid, reliable and cost-effective quality control procedures. Currently, microscopy-based techniques are used to measure the lateral size and thickness of particles but while powerful, these techniques suffer from limitations such as lengthy analysis time, high costs and limited sampling. In the case of carbon-based 2D materials, as the stacking of multiple graphene sheets causes a reduction in the surface to mass ratio, the number of layers can hypothetically be calculated by comparing the theoretical surface area of monolayer graphene (2630 m2/g) to the calculated specific surface area (SSA) measured by gas physisorption measurements. However, despite the potential of this method of analysis, there is limited understanding regarding the characterisation of commercial graphene/graphite powders produced via bottom-up and top-down methods. Herein, the SSAs of a variety of commercially-available graphitic powders were measured using nitrogen physisorption isotherms at 77 K and applying Brunauer-Emmett-Teller theory. The as-obtained SSAs were then correlated to the structural and chemical properties of the materials (obtained using conventional techniques) to demonstrate the suitability of this measurement technique for quality control of graphitic powder

Crop Updates 2000 - Weeds

This session covers thirty six papers from different authors: INTRODUCTION, Vanessa Stewart Agriculture Western Australia INTEGRATED WEED MANAGEMENT Effect of seeding density, row spacing and Trifluralin on the competitive ability of Annual Ryegrass in a minimum tillage system, David Minkey, Abul Hashem, Glen Riethmuller and Martin Harries, Agriculture Western Australia High wheat seeding rates coupled with narrow row spacing increases yield and suppresses grass, Peter Newman1 and Cameron Weeks2,1Agronomist, Elders Limited 2Mingenew/Irwin Group Resistant ryegrass management in a wheat – lupin rotation, Abul Hashem, Harmohinder S. Dhammu, Aik Cheam, David Bowran and Terry Piper, Agriculture Western Australia Integrated weed management – Will it work with my rotation? Alexandra Wallace, Agriculture Western Australia Long term herbicide resistance trial – Mingenew, Peter Newman Elders, Cameron Weeks Mingenew-Irwin Group Is two years enough? Bill Roy, Agricultural Consulting and Research Services The fate of ryegrass seed when sheep graze chaff cart heaps, Keith L. Devenish1 and Lisa J. Leaver2 1 Agriculture Western Australia, 2Curtin University of Technology, Muresk Institute of Agriculture Can blanket wiping and crop topping prevent seed set of resistant wild radish and mustard? StAbul Hashem, Harmohinder Dhammu, Vanessa Stewart, Brad Rayner and Mike Collins, Agriculture Western Australia The value of green manuring in the integrated management of ryegrass, Marta Monjardino1,2, David Pannell2, Stephen Powles1 ,1Western Australia Herbicide Resistance Initiative, 2Agricultural and Resource Economics, University of Western Australia Some ways of increasing wheat competitiveness against ryegrass,, Mike Collins Centre for Cropping Systems, Agriculture Western Australia WEED BIOLOGY Understanding and driving weed seed banks to very low levels, Sally Peltzer, Agriculture Western Australi HERBICIDE RESISTANCE Cross resistance of chlorsulfuron-resistant wild radish to imidazolinones, Abul Hashem, Harmohinder Dhammu and David Bowran, Agriculture Western Australia Investigation of suspected triazine resistant ryegrass populations for cross-resistance and multiple resistance to herbicides, Michael Walsh, Charles Boyle and Stephen Powles, Western Australian Herbicide Resistance Initiative, University of Western Australia Genetics and fitness of glyphosate resistant ryegrass, S. Powles1, P. Neve1, D. Lorraine-Colwill2, C. Preston2 ,1WAHRI, University of Western Australia 2 CRC Weed Management Systems, University of Adelaide Managing herbicide resistance – the effect of local extinction of resistance genes, Art Diggle1, Paul B. Neve2, Stephen B. Powles2 ,1Agriculture Western Australia, 2WAHRI, Faculty of Agriculture, University of Western Australia The double knock - the best strategy for conserving glyphosate susceptibility? Paul B. Neve1, Art Diggle2, Stephen B. Powles1,1WAHRI, Faculty of Agriculture, University of Western Australia, 2Agriculture Western Australia Wild radish had evolved resistance to triazines, Abul Hashem, Harmohinder S. Dhammu, David Bowran and Aik Cheam, Agriculture Western Australia Ryegrass resistance in Western Australia – where and how much? Rick Llewellyn and Stephen Powles, Western Australian Herbicide Resistance Initiative, Faculty of Agriculture, University of Western Australia Wild radish herbicide resistance survey, Michael Walsh, Ryan Duane and Stephen Powles, Western Australian Herbicide Resistance Initiative, University of Western Australia Knockdown resistance in the Western Australian wheatbelt – a proposed survey, Paul B. Neve1, Abul Hashem2, Stephen B. Powles1,1Western Australian Herbicide Resistance Initiative, University of Western Australia, 2Agriculture Western Australia Diflufenican resistant wild radish, Aik Cheam, Siew Lee, David Bowran, David Nicholson and Abul Hashem, Agriculture Western Australi Multiple resistance to triazines and diflufenican further complicates wild radish control, Aik Cheam, Siew Lee, David Bowran, David Nicholson and Abul Hashem, Agriculture Western Australia HERBICIDE TOLERANCE 25. Herbicide tolerance of lupins, Terry Piper, Weed Science Group, Agriculture Western Australia 26. Tanjil lupins will tolerate metribuzin under the right conditions, Peter Newman, Agronomist Elders Limited and Cameron Weeks, Mingenew/Irwin Group 27. Herbicide damage does not mean lower yield in Lupins, Peter Carlton, Trials Coordinator, Elders Limited 28. Herbicide tolerance of new pea varieties, Dr Terry Piper, Agriculture Western Australia 29. Herbicide tolerance of (waterlogged) wheat, Dr Terry Piper, Agriculture Western Australia 30. Wheat tolerance trials – Mingenew 1999, Peter Newman1, Cameron Weeks2 and Stewart Smith3,1Elders, Mingenew, 2Mingenew-Irwin Group,3Agriculture Western Australia ISSUES OF TRIFLURALIN USE 31. Trifluralin works better on ryegrass when no-tilling into thick wheat stubbles as granules, or mixed with limesand, Bill Crabtree, WANTFA Scientific Officer 32. Increasing trifluralin rate did not compensate for delaying incorporation, Bill Crabtree, WANTFA Scientific Officer 33. Poor emergence survey, 1999, Terry Piper, Weed Science Group, Agriculture Western Australia HERBICIDES – ISSUES AND OPTIONS 34. AFFINITY 400DF – A new herbicide with a new mode of action (Group G) for Broadleaf Weed Control in Cereals, Gordon Cumming, Technical Officer, Crop Care Australasia 35 Herbicide screening for Marshmallow, David Minkey1 and David Cameron2,1Agriculture Western Australia, 2Elders Ltd, Merredin 36. The control of Capeweed in Clearfield Production System for Canola, Mike Jackson and Scott Paton, Cyanamid Agriculture Pty Ltd 37.Effect of herbicides Tordonä 75D and Lontrelä,used for eradication of Skeleton Weed, on production of Lupins I the following seasons, John R. Peirce and Brad J. Rayner, Agriculture Western Australia INDUSTRY PROTECTION 38. Graingaurd – Opportunities for agribusiness to help protect the West Australian grains industry, Greg Shea, Executive Officer, GrainGuard Agriculture Western Australi

Scalable production of large quantities of defect-free few-layer graphene by shear exfoliation in liquids

To progress from the laboratory to commercial applications, it will be necessary to develop industrially scalable methods to produce large quantities of defect-free graphene. Here we show that high-shear mixing of graphite in suitable stabilizing liquids results in large-scale exfoliation to give dispersions of graphene nanosheets. X-ray photoelectron spectroscopy and Raman spectroscopy show the exfoliated flakes to be unoxidized and free of basal-plane defects. We have developed a simple model that shows exfoliation to occur once the local shear rate exceeds 10(4) s(-1). By fully characterizing the scaling behaviour of the graphene production rate, we show that exfoliation can be achieved in liquid volumes from hundreds of millilitres up to hundreds of litres and beyond. The graphene produced by this method performs well in applications from composites to conductive coatings. This method can be applied to exfoliate BN, MoS2 and a range of other layered crystals

A survey of foot orthoses prescription habits amongst podiatrists in the UK, Australia and New Zealand

Background: Foot orthoses are frequently used but little is known about which types are used in contemporary practice. This study aimed to explore the types of foot orthoses currently used by podiatrists and the prescription variations in a range of conditions. Methods: A web-based, cross-sectional survey was distributed through professional bodies in the United Kingdom (UK), Australia, and New Zealand. Questions focussed on foot orthosis prescription habits in relation to 26 conditions affecting the back and lower limb. Results: Two hundred and sixty-four podiatrists practising in 19 different countries completed the survey; the majority practised in the UK (47%, n=124), Australia (30%, n=79) and New Zealand (12%, n=32). Respondents qualified between 1968 and 2016, and 147 (56%) were female. Respondents worked in different healthcare sectors and this varied between countries: 42 (34%) respondents in the UK worked solely in the public sector, compared to 3 (4%) in Australia and 2 (6%) in New Zealand. Forty-four (35%) respondents in the UK worked solely in private practice, compared to 64 (81%) in Australia and 14 (44%) in New Zealand. UK respondents prescribed more prefabricated orthoses per week (mean 5.5 pairs) than simple insole-type devices (±2.7) and customised devices (±2.9). Similarly, respondents in New Zealand prescribed more prefabricated orthoses per week (±7.7) than simple (±1.4) and customised (±2.8) devices. In contrast, those in Australia prescribed more customised orthoses per week (±4.4) than simple (±0.8) and prefabricated (±1.9) orthoses. Differences in the types of orthoses prescribed were observed between country of practice, working sector, and the condition targeted. Generally, prefabricated orthoses were commonly prescribed for the 26 highlighted conditions in the UK and New Zealand. Australian podiatrists prescribed far fewer devices overall, but when they did prescribe, they were more likely to prescribe custom devices. Respondents in all three countries were more likely to prescribe customised orthoses for people with diabetes complicated by peripheral neuropathy than for diabetes without this complication. Conclusions: Foot orthosis prescription habits vary between countries. Prefabricated orthoses were frequently prescribed in the UK and New Zealand, and customised orthoses in Australia. Prescriptions for people with diabetes differed depending on the presence of neuropathy, despite a lack of robust evidence supporting these decisions. This study provides new insight into contemporary practice

Systematic review of methods used in meta-analyses where a primary outcome is an adverse or unintended event

addresses: Peninsula College of Medicine and Dentistry, St Luke's Campus, University of Exeter, Exeter, UK. [email protected]: PMCID: PMC3528446types: Journal Article; Research Support, Non-U.S. Gov't© 2012 Warren et al.; licensee BioMed Central Ltd. This is an Open Access article distributed under the terms of the Creative Commons Attribution License ( http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.Adverse consequences of medical interventions are a source of concern, but clinical trials may lack power to detect elevated rates of such events, while observational studies have inherent limitations. Meta-analysis allows the combination of individual studies, which can increase power and provide stronger evidence relating to adverse events. However, meta-analysis of adverse events has associated methodological challenges. The aim of this study was to systematically identify and review the methodology used in meta-analyses where a primary outcome is an adverse or unintended event, following a therapeutic intervention