Thermal performance of additively manufactured polymer lattices

The energy performance of buildings is a key point to achieve the sustainability goals of the modern world. The reduction of the heat loss by incorporating porosity in a monolithic material was studied. To this aim, lattice structures with varying lattice topology and specimen size were synthesised using polymer based additive manufacturing. Commercially available 3D printers and polymer filaments were utilised to manufacture such polymer lattices. Their thermal performance was characterised using a bespoke compact temperature-change hot chamber. A scaling law, based on the experimental results, has been proposed for the first time to predict the Uvalue of polymer lattices by correlating their effective thermal conductivities. It was observed that the lattice’s relative density and the sizes of a unit cell and specimen affected significantly the U-value. Also, it was found that polymer-lattice structures can be designed to only allow a conductive mode of heat transfer when their hydraulic diameter was less than 8 mm. The effect of an AM process parameters such as the layer thickness and type of 3D printer on the U-value of the polymer lattices was also characterised and found that they had a mild effect on the U-value of the lattices. Thus, a highly optimised lattice structure, aiming at achieving the higher thermal resistance to make it suitable for energy saving applications, can be obtained using the proposed scaling law

Shape analysis of prosthetic socket rectification procedure for transtibial amputees

Achieving a comfortable socket residual limb interface is crucial for effective prosthetic rehabilitation, depending on the precise characterisation and fluctuations in the shape and volume of residual limbs. Clinicians rely on subjective and iterative methods for shaping sockets, often involving a trial-and-error approach. This study introduces a framework for measuring, analysing, and comparing residual limb shape and volume using scanned data to facilitate more informed clinical decision-making. Surface scans of 44 transtibial residual limb casts of various sizes and lengths were examined. All scans were spatially aligned to a mid-patella and subjected to analysis using a shape analysis toolbox. Geometric measurements were extracted, with particular attention to significant rectified regions during the cast rectification process. Following PTB guidelines, our analysis revealed substantial alterations, primarily in the mid-patella region, followed by the patellar tendon area. Notably, there was a significant volume change of 6.02% in the region spanning from mid-patella to 25% of the cast length. Beyond this point, linear cast modifications were observed for most amputees up to 60% of the cast length, followed by individual-specific deviations beyond this region. Regardless of residual limb size and length, the modifications applied to positive casts suggested categorising patients into five major groups. This study employs the AmpScan shape analysis tool, to comprehend the cast rectification process used for capturing and assessing the extent of rectification on patients’ residual limb casts. The clinical implications of our research are threefold: (a) the comparison data can serve as training resources for junior prosthetists; (b) this will aid prosthetists in identifying specific regions for rectification and assessing socket fit; (c) it will help in determining optimal timing for prosthetic fitting or replacement.</p

Strength assessment of PET composite prosthetic sockets

A prosthesis is loaded by forces and torques exerted by its wearer, the amputee, and should withstand instances of peak loads without failure. Traditionally, strong prosthetic sockets were made using a composite with a variety of reinforcing fibres, such as glass, carbon, and Kevlar. Amputees in less-resourced nations can lack access to composite prosthetic sockets due to their unavailability or prohibitive cost. Therefore, this study investigates the feasibility of polyethylene terephthalate (PET) fibre-reinforced composites as a low-cost sustainable composite for producing functional lower-limb prosthetic sockets. Two types of these composites were manufactured using woven and knitted fabric with a vacuum-assisted resin transfer moulding (VARTM) process. For direct comparison purposes, traditional prosthetic-socket materials were also manufactured from laminated composite (glass-fibre-reinforced (GFRP)), monolithic thermoplastic (polypropylene (PP) and high-density polyethylene (HDPE)) were also manufactured. Dog-bone-shaped specimens were cut from flat laminates and monolithic thermoplastic to evaluate their mechanical properties following ASTM standards. The mechanical properties of PET-woven and PET-knitted composites were found to have demonstrated to be considerably superior to those of traditional socket materials, such as PP and HDPE. All the materials were also tested in the socket form using a bespoke test rig reproducing forefoot loading according to the ISO standard 10328. The static structural test of sockets revealed that all met the target load-bearing capacity of 125 kg. Like GFRP, the PETW and PETK sockets demonstrated higher deformation and stiffness resistance than their monolithic counterparts made from PP and HDPE. As a result, it was concluded that the PET-based composite could replace monolithic socket materials in producing durable and affordable prostheses