Instrument Systems Analysis and Verification Facility (ISAVF) users guide

The ISAVF facility is primarily an interconnected system of computers, special purpose real time hardware, and associated generalized software systems, which will permit the Instrument System Analysts, Design Engineers and Instrument Scientists, to perform trade off studies, specification development, instrument modeling, and verification of the instrument, hardware performance. It is not the intent of the ISAVF to duplicate or replace existing special purpose facilities such as the Code 710 Optical Laboratories or the Code 750 Test and Evaluation facilities. The ISAVF will provide data acquisition and control services for these facilities, as needed, using remote computer stations attached to the main ISAVF computers via dedicated communication lines

Regeneration of thermally recycled glass fibre for cost-effective composite recycling : increasing the strength of thermally conditioned glass fibres using cost effective recover treatments

The paper reports an extensive study on the regenerating performance of thermally treated glass fibres using two different chemically based treatments routes. The effectiveness of these two different treatments was investigated on strength recovery of glass fibres thermally treated with the conditions imitating composite recycling technology. The regenerated strength levels of these ReCoVeRed fibres must also be further protected and maintained by the use of standard fibre sizing technology similar to standard glass fibre products. Consequently, the effect on fibre strength of the combination of our ReCoVeR treatments with the standard silane coatings was also studied. Significant increase of fibre strength was obtained through the ReCoVeR and coatings treatments, achieving up to 200% increase in fibre strength in comparison with the glass fibre thermally treated

A simple chemical approach to regenerating strength of thermally damaged glass fibre for reuse in composites

A key technical barrier to the reuse of thermally recycled glass fibres in composite applications is their low mechanical strength. This research study looks into the effect of alkaline treatments in regenerating the strength of glass fibres which were heated in a furnace to simulate thermal recycling conditions. Up to 100% strength increase of the fibres can be achieved through a simple treatment in alkaline solution. It was found that the nature of alkali, concentration, and treatment duration had a significant effect on the extent of strength recovery of the fibres. These treatments could potentially be implemented to thermally recycled glass fibres on an industrial scale, to allow their reprocessing into second-life composite materials. As well as optimising the reaction conditions to regenerate fibre strength, an examination of the surface morphology was carried out using various techniques. In addition, the kinetics of dissolution of glass fibres in alkaline solutions was investigated in order to further understand the strength regeneration mechanism

An exploration of the relationship of chemical and physical parameters in the micromechanical characterisation of the apparent interfacial strength in glass fibre epoxy systems

This paper focuses on the cure shrinkage and the thermomechanical properties of an amine cured epoxy resin system and its adhesion to glass fibre. The fibre-matrix interfacial shear strength (IFSS) was characterized using the microbond test over a range of test temperatures and a range of amine:epoxy ratios. The apparent IFSS in this glass-epoxy system was shown to be strongly dependent on the testing temperature and the matrix stoichiometry. High levels of cure shrinkage were measured in the IFSS microdroplets which resulted in internal stresses causing significant levels of droplet deformation. The results presented here can be interpreted as providing further support for the hypothesis that a significant fraction of the interfacial stress transfer capability in epoxy composites can be attributed to a combination of residual radial compressive stress and static friction at the fibre-matrix interface

Regenerating the strength of thermally recycled glass fibres using hot sodium hydroxide

Results are presented from the ReCoVeR project on the regeneration of the strength of thermally conditioned glass fibres. Thermal recycling of end-of-life glass fibre reinforced composites or composite manufacturing waste delivers fibres with virtually no residual strength or value. Composites produced from such fibres also have extremely poor mechanical performance. Data is presented showing that a short hot sodium hydroxide solution treatment of such recycled fibres can more than triple their strength and restore their ability to act as an effective reinforcement in second life composite materials. The implications of these results for real materials reuse of recycled glass fibres as replacement for pristine reinforcement fibres are discussed

Effects of thermal recycling temperatures on the reinforcement potential of glass fibers

In the present work the reinforcement potential of thermally recycled glass fibers in injection molded Polypropylene (PP) composites was investigated. Microbond tests showed that fiber sizing lost its compatibility to the PP matrix after exposure to temperatures of 250 °C in air. The drop of the adhesion between fibers and PP was mirrored by a large reduction of the tensile strength of the injection molded PP composites. In inert atmosphere the degradation of the fiber sizing and the reduction of the IFSS were less rapid than in air but no significant difference was observed above 400 °C. It was concluded that thermally recycled glass fibers will require a post-treatment to act as an effective reinforcement in injection molded PP composites even if the thermal recycling was performed in an inert atmosphere. The post-treatment will need to improve the compatibility of the fibers to the polymer matrix and the fiber strength

Glass fibre sizing : a review

Glass fibre reinforcements form the backbone of a composites industry with a global annual production of more than 10 million tons of high performance, light-weight materials. Possibly the most critical component involved in the manufacture of glass fibres and their composites is the fibre sizing. Yet because of the intense level of secrecy surrounding size formulations there are very few people in the vast supply chain of composite materials suppliers, processors and end users who have more than a superficial understanding of glass fibre sizings. Given the importance of sizings to the continuing success and growth of the composites industry this paper reviews some of the most relevant articles from the widely dispersed literature available around glass fibre sizings. The review covers size formulation, sizing effects in fibre and composite processing, sizing and fibre performance, sizing and interphase adhesion, and sizing effects on composite performance. The conclusions highlight the fragmented nature of the knowledge base on sizings and the lack of reliable and reproducible reference materials on which to build real progress in this critical technology

Monotone graph limits and quasimonotone graphs

The recent theory of graph limits gives a powerful framework for understanding the properties of suitable (convergent) sequences $(G_n)$ of graphs in terms of a limiting object which may be represented by a symmetric function $W$ on $[0,1]$, i.e., a kernel or graphon. In this context it is natural to wish to relate specific properties of the sequence to specific properties of the kernel. Here we show that the kernel is monotone (i.e., increasing in both variables) if and only if the sequence satisfies a `quasi-monotonicity' property defined by a certain functional tending to zero. As a tool we prove an inequality relating the cut and $L^1$ norms of kernels of the form $W_1-W_2$ with $W_1$ and $W_2$ monotone that may be of interest in its own right; no such inequality holds for general kernels.Comment: 38 page

The sequelae of a missed Essex-Lopresti lesion

Radial head fractures are the most common type of elbow fracture in adults. Unrecognised disruption of the intraosseous membrane at the time of injury can lead to severe wrist pain from proximal radial migration especially if the radial head is excised. In this case, despite anatomical reduction and internal fixation of the radial head fracture, longitudinal forearm instability developed after delayed radial head resection was performed 7 months post-injury. A Suave-Kapandji procedure was performed due to ongoing wrist pain. Because of the previous radial head resection, this led to a floating forearm that could only be solved by creating a one-bone forearm, sacrificing all forearm rotation to achieve a stable lever arm between the elbow and wrist joint

On the vanishing of negative K-groups

Let k be an infinite perfect field of positive characteristic p and assume that strong resolution of singularities holds over k. We prove that, if X is a d-dimensional noetherian scheme whose underlying reduced scheme is essentially of finite type over the field k, then the negative K-group K_q(X) vanishes for every q < -d. This partially affirms a conjecture of Weibel.Comment: Math. Ann. (to appear