1-DOF Model for Fluid-Structure-Interaction Vibration Analysis

In this paper an attempt to provide a single degree of freedom lumped model for fluid structure interaction (FSI) dynamical analysis will be presented. The model can be used to clarify some important concept in the FSI dynamics such as the added mass, added stiffness, added damping, wave coupling ,influence mass coefficient and critical fluid depth . The numerical results of the model show that the natural frequency decrease with the increasing of many parameters related to the structure and the fluid .It is found that the interaction phenomena can become weak or strong depending on the depth of the containing fluid .The damped and un damped free response are plotted in time domain and phase plane for different model parameters It is found that the vibration free response is still sinusoidal for weak FSI coupling ,however for strong coupling it behaves as modulated periodic response .To justify some of the theoretical aspects such as; the effects of the fluid density and the interact shape on the natural frequency an experiment was conducted .The results of the experiment shows a good agreement with the theory where the error is not exceeded 7%

Natural Frequencies of Multi-Irregular Span Beams under Elastic Supports By Modal Analysis Method

Evaluating the natural frequencies of multi- span beams with elastic supports play a major role in vibration designing and optimizing of many structures such as bridges, railways ,pipes and so on The continuity of the boundary conditions ,state space and numerical methods are normally used to investigate the vibration characteristics of such structures .Unfortunately ,such methods lead to high size matrix in dealing with the boundary value problem as the number of spans increase. In the present work, the problem is solved analytically by using Modal Analysis techniques in which the continuous system is discreteized to finite degree of freedoms in terms of the generalized coordinates A proper shape function are employed for describing the system dynamical behavior and satisfying the boundary conditions .In the present method the size of the resulting Eigen matrix depends on the number of mode chosen regardless of the number of spans. With this method wide variety of support configurations can be treated. The validly and convergence of the present method for calculating the natural frequencies is carefully checked by comparing with the exact values for two-span beams with different boundary conditions . It is found that using only (5) modes for the assumed solution gives only 2% error for two span simply supported and free ends beam , however for clamped ends the error is 8% .The present method is further checked by comparing with the Finite Element method the results show good agreements where the error is not increases 1% .The results of the natural frequencies of up to (10) equal and unequal spans beams under different boundary conditions and support stiffness are presented .The results showed that the natural frequencies can be highly controlled by proper choosing of the structure parameters and support stiffness. Keywords: , , ,

Effect of Head Types on the Free Vibration and Fatigue for Horizontal LPG Pressure Vessels

Pressure vessels are the heart of plants and oil refineries stations. In many engineering applications such vessels can be subjected to periodic loading either internally due to the charging and discharging process or externally due to the excitation from other nearby components such as pumps, compressors or from seismic. So that in spite of a good design according static assumption it may be critical in dynamics. In this work a horizontal pressure vessel with accessories subjected to liquefied petroleum gas pressure LPG is considered. Three models of different head types are investigated herein namely; Deep torispherical, Elliptical 2:1 and Hemispherical. The design and material selections are chosen as per ASME. For practical service many accessories are attached to the vessel such as manhole, supports, inlet and outlet opining. Finite Element method via ANSYS R18.2 is introduced for the numerical analysis. The fatigue life in case of fully reversed cyclic loading are estimated and located. Vibration characteristics such as mode shapes and natural frequencies for the lowest five modes are evaluated and compared. It is found that the fatigue life can be increased as higher as 180% for hemi- spherical head as compared with deep torispherical head pressure vessel and the lowest four natural frequencies are nearly identical for all models, however significant change observed in the fifth natural frequency

Buckling analysis of reinforced composite plates with a multiwall carbon nanotube (MWCNT)

Buckling analysis of mechanical structures is essential to insure stability under loading .Critical load of buckling refer to the maximum load can be withstood without losing of stability and avoid a catastrophic damage due to the collapse of columns .Improving of mechanical properties spatially those related with elastic behaviors of materials can lead to improving buckling since it can be raised the value of critical load . Nanotechnology is one of the modern methods which makes significant effects on the mechanical properties of materials. In the field of composite materials this technology leads to valuable improvements for the favorite properties. In this regard Nano composite materials are paid a spatial attention in research for the last decade. The main aim of the present work is to investigate the effect of Nano carbon weight fraction on buckling of the composite plate. Five samples of Nano composite plates were prepared and fabricated for experimental investigations .The plate samples are combined of woven reinforcement fiber and polyester matrix with Carbon .The weight fraction of Nano additives are 0 %, 0.5%, 1%, ,1.5 and 2%, of resin materials weight. To provide homogenous composite an ultrasonic homogenizer is utilized. The experimental work include buckling test for different Nano plates samples with simply supported at two ends and free at the other .Finite Element analysis was achieved via ANSYS R15.0 with proper elements ,meshing ,boundary condition and static analysis .It is found that increasing of Nano carbon weight ratio tends to increase critical load of buckling ,the maximum buckling load is at 2% wt ratio and the experimental results shows fair validation for the numerical analysis where the maximum error dos not exceeded 15%

Theoritical and Experimental Investigation of the Dynamical Behaviour of Complex Configuration Rotors

The present work considers an alternative solution for a complex configuration of rotor discs by applying Galerkin Method. The theoretical model consists of elastic shaft carrying number of discs and supported on number of journal bearings. The equation of motion was discretized to finite degree of freedom in terms of the system generalized coordinates. The various effects of the dynamical forces and moments arising from the bearing, discs and shaft were included. Rayleigh beam model is used for analyzing the shaft while the discs are considered rigid . The validity and convergence of the present analysis was carefully checked by comparing with the Finite Element solution. An example of rotor consists of three different size discs and supported by two journal bearing was considered for the numerical solution .The results shows good agreements between the two methods ,where the maximum error not exceeds 5%. The convergence test showed that using few modes (not more than 6) are sufficient for the accurate analysis. The forward and backward whirl was investigated experimentally .The experimental results of a two discs rotor ,show a reasonable agreement where the maximum error not exceeds 11%. The unbalance response, Cambpell diagram, orbit response were plotted .The effects of geometry, disc sizes , location and arrangement on the unbalance response and natural frequencies of three discs rotor were further investigated

Impact of opioid-free analgesia on pain severity and patient satisfaction after discharge from surgery: multispecialty, prospective cohort study in 25 countries

Background: Balancing opioid stewardship and the need for adequate analgesia following discharge after surgery is challenging. This study aimed to compare the outcomes for patients discharged with opioid versus opioid-free analgesia after common surgical procedures.Methods: This international, multicentre, prospective cohort study collected data from patients undergoing common acute and elective general surgical, urological, gynaecological, and orthopaedic procedures. The primary outcomes were patient-reported time in severe pain measured on a numerical analogue scale from 0 to 100% and patient-reported satisfaction with pain relief during the first week following discharge. Data were collected by in-hospital chart review and patient telephone interview 1 week after discharge.Results: The study recruited 4273 patients from 144 centres in 25 countries; 1311 patients (30.7%) were prescribed opioid analgesia at discharge. Patients reported being in severe pain for 10 (i.q.r. 1-30)% of the first week after discharge and rated satisfaction with analgesia as 90 (i.q.r. 80-100) of 100. After adjustment for confounders, opioid analgesia on discharge was independently associated with increased pain severity (risk ratio 1.52, 95% c.i. 1.31 to 1.76; P < 0.001) and re-presentation to healthcare providers owing to side-effects of medication (OR 2.38, 95% c.i. 1.36 to 4.17; P = 0.004), but not with satisfaction with analgesia (beta coefficient 0.92, 95% c.i. -1.52 to 3.36; P = 0.468) compared with opioid-free analgesia. Although opioid prescribing varied greatly between high-income and low- and middle-income countries, patient-reported outcomes did not.Conclusion: Opioid analgesia prescription on surgical discharge is associated with a higher risk of re-presentation owing to side-effects of medication and increased patient-reported pain, but not with changes in patient-reported satisfaction. Opioid-free discharge analgesia should be adopted routinely

Reducing the environmental impact of surgery on a global scale: systematic review and co-prioritization with healthcare workers in 132 countries

Abstract Background Healthcare cannot achieve net-zero carbon without addressing operating theatres. The aim of this study was to prioritize feasible interventions to reduce the environmental impact of operating theatres. Methods This study adopted a four-phase Delphi consensus co-prioritization methodology. In phase 1, a systematic review of published interventions and global consultation of perioperative healthcare professionals were used to longlist interventions. In phase 2, iterative thematic analysis consolidated comparable interventions into a shortlist. In phase 3, the shortlist was co-prioritized based on patient and clinician views on acceptability, feasibility, and safety. In phase 4, ranked lists of interventions were presented by their relevance to high-income countries and low–middle-income countries. Results In phase 1, 43 interventions were identified, which had low uptake in practice according to 3042 professionals globally. In phase 2, a shortlist of 15 intervention domains was generated. In phase 3, interventions were deemed acceptable for more than 90 per cent of patients except for reducing general anaesthesia (84 per cent) and re-sterilization of ‘single-use’ consumables (86 per cent). In phase 4, the top three shortlisted interventions for high-income countries were: introducing recycling; reducing use of anaesthetic gases; and appropriate clinical waste processing. In phase 4, the top three shortlisted interventions for low–middle-income countries were: introducing reusable surgical devices; reducing use of consumables; and reducing the use of general anaesthesia. Conclusion This is a step toward environmentally sustainable operating environments with actionable interventions applicable to both high– and low–middle–income countries

Reducing the environmental impact of surgery on a global scale: systematic review and co-prioritization with healthcare workers in 132 countries

Background Healthcare cannot achieve net-zero carbon without addressing operating theatres. The aim of this study was to prioritize feasible interventions to reduce the environmental impact of operating theatres. Methods This study adopted a four-phase Delphi consensus co-prioritization methodology. In phase 1, a systematic review of published interventions and global consultation of perioperative healthcare professionals were used to longlist interventions. In phase 2, iterative thematic analysis consolidated comparable interventions into a shortlist. In phase 3, the shortlist was co-prioritized based on patient and clinician views on acceptability, feasibility, and safety. In phase 4, ranked lists of interventions were presented by their relevance to high-income countries and low–middle-income countries. Results In phase 1, 43 interventions were identified, which had low uptake in practice according to 3042 professionals globally. In phase 2, a shortlist of 15 intervention domains was generated. In phase 3, interventions were deemed acceptable for more than 90 per cent of patients except for reducing general anaesthesia (84 per cent) and re-sterilization of ‘single-use’ consumables (86 per cent). In phase 4, the top three shortlisted interventions for high-income countries were: introducing recycling; reducing use of anaesthetic gases; and appropriate clinical waste processing. In phase 4, the top three shortlisted interventions for low–middle-income countries were: introducing reusable surgical devices; reducing use of consumables; and reducing the use of general anaesthesia. Conclusion This is a step toward environmentally sustainable operating environments with actionable interventions applicable to both high– and low–middle–income countries

Estimating Transfer Function of Below-Knee Prosthesis at Two Phases of Gait Cycle

The modern development in prosthetics field demand the evaluation of the dynamical behavior and automatic control .The key process in the design and implement of these devices is the determination of the model parameters inherited with the transfer function .In such complicated structures it is so difficult to evaluate transfer function analytically ,however experimental approaches can serve as a simple and effective tool for estimating transfer function and model parameters .In this regard computer software such as Matlab is used .System Identification SID refers to the method for estimating the system transfer function from experimental tests by using computer .In the present paper; SID method is employed for analyzing below-knee prosthesis leg .In order to simulate with the practical requirement for design and evaluation ,two phases of human gait are considered ,namely; swing phase and single support of stance phase .The validity of this method is firstly checked by applying it on clamped-clamped beam model where the required parameters are evaluated and compared theoretically (via modal analysis) and experimentally (via System identification) .It is found that ; the error in estimating the transfer function parameter of beam is not exceeded 6% . Then the transfer function of the prosthesis are estimated for two phases of gait cycle .It is found that; the estimated transfer function of the prosthesis leg is highly affected by the phase type of gait cycle , where ;the natural frequency highly increases, the static gain decrease for support phase as compared with the swing phase ,however the damping ratio does not affected