Control of Ni/Ce1-xMxOy catalyst properties via the selection of dopant M = Gd, La, Mg Part 1. Physicochemical characteristics

To elucidate the role of support composition in autothermal reforming of ethanol (ATR of C2H5OH), a series of Ni catalysts (Ni content 2–15 wt.%) supported on different ceria-based oxides (Ce1-xGdxOy, Ce1-xLaxOy and Ce1-xMgxOy; x = 0.1–0.9) were prepared. The synthetized materials were tested in ATR of ethanol at 200–700 °C. It was established that supports themselves show catalytic activity in ATR of C2H5OH and provide 10–15% yield of H2 at 700 °C. Upon the increase of Ni content from 2 to 15 wt.% the temperature of 100% ethanol conversion decreases from 700 tо 300 °С, hydrogen yield increases from 25 to 60%, the inhibition of С2-С3 by-products formation, as well as the promotion of decomposition of acetaldehyde occur. The enhancement of catalyst performance in ATR of C2H5OH has been observed in the next series of supports: Ce1-xMgxOy < Ce1-xGdxOy < Ce1-xLaxOy and with a decrease of x to an optimal value that correlates with the improvement of Ni active component reducibility. At 600 °C on 10Ni/Ce0.8La0.2O1.9 catalyst the H2 yield of 50% was achieved at C2H5OH conversion of 100%. Stable and high performance of developed catalysts in ATR of C2H5OH indicates the promise of their use in the production of hydrogen

Control of Ni/Ce1-xMxOy Catalyst Properties Via the Selection of Dopant M = Gd, La, Mg. Part 2. Catalytic Activity

To elucidate the role of support composition in autothermal reforming of ethanol (ATR of C2H5OH), a series of Ni catalysts (Ni content 2–15 wt.%) supported on different ceria-based oxides (Ce1-xGdxOy, Ce1-xLaxOy and Ce1-xMgxOy; x = 0.1–0.9) were prepared. The synthetized materials were tested in ATR of ethanol at 200–700 °C. It was established that supports themselves show catalytic activity in ATR of C2H5OH and provide 10–15% yield of H2 at 700 °C. Upon the increase of Ni content from 2 to 15 wt.% the temperature of 100% ethanol conversion decreases from 700 tо 300 °С, hydrogen yield increases from 25 to 60%, the inhibition of С2-С3 by-products formation, as well as the promotion of decomposition of acetaldehyde occur. The enhancement of catalyst performance in ATR of C2H5OH has been observed in the next series of supports: Ce1-xMgxOy < Ce1-xGdxOy < Ce1-xLaxOy and with a decrease of x to an optimal value that correlates with the improvement of Ni active component reducibility. At 600 °C on 10Ni/Ce0.8La0.2O1.9 catalyst the H2 yield of 50% was achieved at C2H5OH conversion of 100%. Stable and high performance of developed catalysts in ATR of C2H5OH indicates the promise of their use in the production of hydrogen

Advancing the speed, sensitivity and accuracy of biomolecular detection using multi-length-scale engineering

Rapid progress in identifying disease biomarkers has increased the importance of creating high-performance detection technologies. Over the last decade, the design of many detection platforms has focused on either the nano or micro length scale. Here, we review recent strategies that combine nano- and microscale materials and devices to produce large improvements in detection sensitivity, speed and accuracy, allowing previously undetectable biomarkers to be identified in clinical samples. Microsensors that incorporate nanoscale features can now rapidly detect disease-related nucleic acids expressed in patient samples. New microdevices that separate large clinical samples into nanocompartments allow precise quantitation of analytes, and microfluidic systems that utilize nanoscale binding events can detect rare cancer cells in the bloodstream more accurately than before. These advances will lead to faster and more reliable clinical diagnostic devices

Deactivation and Regeneration of Mo/ZSM-5 Catalysts for Methane Dehydroaromatization

The methane dehydroaromatization (DHA) was studied over a series of impregnated Mo/ZSM-5 catalysts with different molybdenum contents (1-10 wt.%). It was shown that total methane conversion was decreased by 30% during 12 h of DHA reaction. The benzene formation rate was increased from 0.5 to 13.9 mol C6H6/(gMo·s) when the molybdenum content in the catalyst was lowered from 10 to 1 wt.%. The deactivated Mo/ZSM-5 catalysts were studied by a group of methods: N2 adsorption, XRD, TGDTA, HRTEM and XPS. The content and condensation degree (C/H ratio) of the carbonaceous deposits was found to increase with an increase of either of the following parameters: molybdenum content (1-10 wt.%), reaction temperature (720-780 °C), space velocity (405-1620 h-1), reaction time (0.5-20 h). The stability of Mo/ZSM-5 catalysts in reaction-regeneration cycles was better when the time on stream was shorter. The regeneration conditions of deactivated Mo/ZSM-5 catalysts providing their stable operation under multiple reaction-regeneration cycles have been selected

Development of a Technique and Investigation of Capacitance Characteristics of Electrode Materials for Supercapacitors Based on Nitrogen-Doped Carbon Nanotubes

Carbon nanotubes are widely employed as catalyst supports and electrode materials. In our earlier studies, capacitance characteristics of carbon nanotubes (CNTs) and nitrogen-doped carbon nanotubes (N-CNTs) were measured. Voltammetric curves obtained for nitrogen-doped nanotubes in an acid electrolyte showed pseudocapacitance peaks that were caused by electrochemical processes involving nitrogen-containing functional groups. In this study, measurements were made in a two-electrode cell of a supercapacitor with a hydrophilic polypropylene PORP-A1 film serving as a separator in alkaline (6 M KOH solution) and acid (1 M H2SO4 solution) electrolytes using a PARSTAT 4000 potentiostat/galvanostat. A technique was developed to estimate the contribution of electrical double layer (EDL) by subtracting pseudocapacitance from total capacitance of a cell using the Origin 9 software. The contribution of EDL and pseudocapacitance to the capacitance of supercapacitor cells was estimated. The highest capacitance of an electrode material equal to 97.2 F/g (including the EDL capacitance of 65 F/g) was reached for nanotubes doped with 8.5% of nitrogen in an acid electrolyte at a potential scanning rate of 10 mV/s

The organization of forecasting of major dental diseases among school-age children

The article presents a review of the scientific literature containing data on the modern scientific methods of forecasting of development of dental diseases in children of school age. According to the materials of observations, the resulting pattern of various clinical indicators contributing to the intensive development of nosological forms of diseases of hard tissues of teeth was obtained. The analysis shows the necessity of using mathematical and statistical methods in the prediction of major dental diseases in children of school age.В статье представлен обзор научной литературы, содержащий данные о современных научных методах прогнозирования развития стоматологических заболеваний у детей школьного возраста. По материалам наблюдений получена картина разнообразных клинических показателей способствующих интенсивному развитию нозологических форм заболеваний твердых тканей зубов. Проведенный анализ свидетельствует о необходимости использования математических и статистических методов исследования в прогнозировании основных стоматологических заболеваний у детей школьного возраста

Carbonization and Regeneration of Mo/ZSM-5 Catalysts for Methane Dehydroaromatization

The character of carbonaceous deposits formed during methane dehydroaromatization reaction in the presence of Mo/ZSM-5 catalysts was studied by differential thermal analysis. The dependence of the concentration and condensation degree (C/H ratio) of the carbonaceous deposits on the catalyst synthesis conditions (Mo content = 1-10%, Si/Al ratio in the initial H-ZSM-5 = 17-45) and reaction conditions (feed flow rate = 405-1620 h-1, methane concentration = 90-98%, reaction temperature = 720-780 °C) was investigated. The oxidative treatment conditions of carbonized Mo/ZSM-5 catalysts providing stable operation of the catalysts under multiple reaction-oxidative treatment cycles were selected

New Gas-Phase Catalytic Oxidative Processes for Desulfurization of Diesel Fuel

An effective gas-phase oxidative desulfurization (ODS) process was proposed. The process was studied in a laboratory reactor with a proprietary catalyst at 300-400 ºС and ambient pressure with model fuels represented by thiophene, dibenzothiophene(DBT) and 4,6-dimethyldibenzothiophene (DMDBT) dissolved in octane, isooctane or toluene. The reactivity of different sulfur containing molecules in ODS was shown to increase in the sequence: thiophene<DBT<DMDBT. The main sulfur containing product of oxidation of these compounds was SO2. During the gas-phase ODS both processes of sulfur species oxidation and processes of their adsorption were observed and studied. Based on the conducted studies, different ODS process designs comprising its integration with adsorption and regeneration processes and with conventional hydrodesulfurization (HDS) process were proposed. One scheme is based on alternating regimes of ODS and catalyst regeneration in two reactors: sulfur is removed from organic feedstock by oxidation and adsorption in one reactor while simultaneous regeneration of the catalyst that has accumulated sulfur compounds takes place in another reactor. Two other schemes are based on joint use of ODS and HDS. The conventional HDS process is most effective for removal of low-boiling sulfur containing compounds reactive with respect to hydrogen, while removal of refractory sulfur compounds, such as DMDBT is more easily achieved by gas phase ODS. Thus the combination of these processes is expected to be most efficient for deep desulfurization of diesel fuel

Highly Dispersed Palladium on Carbon Nanofibers for Hydrogenation of Nitrocompounds to Amines

The effect of palladium dispersion and nature of the support on catalytic performance in hydrogenation of nitrobenzene to aniline was studied. It was shown that the type of the support and modification of palladium with phosphorus make it possible to stabilize highly dispersed (1.5-2 nm) palladium particles in the metallic state, thus increasing the efficiency of new catalysts