Konditionierung von Werkstücken durch Rundkneten

Im Rahmen dieser Dissertation wird das Rundkneten als eine Vorstufe zur Konditionierung von Werkstücken für weitere Umformschritte untersucht. Das Rundkneten erweist sich als besonders geeignet zur Erzeugung der Zielgeometrie von Bauteilen. Die Zielsetzung dieser Arbeit besteht darin, den Rundknetprozess so zu gestalten, dass neben der gut tolerierten Geometrie (Durchmesser) und einer guten Oberflächentopologie, die Mikrostruktur des umgeformten Halbzeuges beeinflusst wird und damit vorteilhafte Werkstoffeigenschaften entwickelt werden können, die sodann für nachgelagerte Umformungen wie z. B. den Fließpressprozess, zur Geltung kommen. Im Vorfeld können zu diesem Zweck Modifikationen bereits im Rundknetprozess eingebracht werden. Modifikationen an der Werkzeuggeometrie betreffen dabei das Design der Werkzeuge in den Umformbereichen, und die Modifikationen der Prozesskinematik umfassen Änderungen an Prozessparametern wie den Vorschub pro Schlag, die Hubhöhe oder die relative Bewegung zwischen Werkstück und den rotierenden Werkzeugen. Beim exzentrischen Rundkneten werden beide Prozessmodifikationen kombiniert, was zu Besonderheiten beim Werkstofffluss, der Entwicklung der Mikrostruktur sowie in den mechanischen Eigenschaften führt. Die Visualisierung des Werkstoffflusses nach einer Konditionierung der Halbzeuge erfolgt anhand einer speziellen neuentwickelten Methode. Durch eine Kombination von zwei Doppelflachwerkzeugen mit einem modularen Werkzeug, bei einem definierten Schlagfolgewinkel und einem spezifischen axialen Vorschub pro Hub, bildet sich während des Prozesses ein schraubenförmiger Kanal. Die Steigung des resultierenden gewindeartigen Kanals korreliert dabei mit dem axialen Fluss in Vorschubrichtung. Durch die Charakterisierung rundgekneteter Werkstücke bei der Prozesskette „Rundkneten/Fließpressen“ kann das Umformvermögen durch den Kraftbedarf beurteilt werden. Dabei können Schlüsse gezogen werden, inwiefern das Rundkneten als erster Schritt für nachfolgende Umformoperationen eingesetzt werden kann. In Kooperation mit einem industriellen Partner konnten konditionierte Halbzeuge bereits bei der Produktion von Kleinschrauben eingesetzt werden

Influence of the relative rotational speed on component features in micro rotary swaging

Micro rotary swaging is a cold forming process for production of micro components with determined geometry and surface. It is also possible to change the microstructure of wires and hence the material properties. Swaging dies revolve around the work piece with an overlaid radial oscillation. Newly developed tools (Flat Surface Dies, FSD) feature plain surfaces and do not represent the geometry of the formed part as in conventional swaging. Using these tools allows for producing wires with triangle geometry (cross section) as well as a circular shape. To test the influence of FSD on material properties by micro swaging a new method is investigated: the variation of the relative speed between the specimen and dies in infeed rotary swaging. During this specific process copper (C11000) and steel (304 Alloy) wires with diameter d0 = 1 mm are formed. It is noticed that the mechanical characteristics such as ductility and strength differ from the characteristics after conventional swaging. Moreover this approach enables new possibilities to influence the geometry and the surface quality of wires. The impact of the relative speed on the processed wire features is described in this paper

Influence of the relative rotational speed on component features in micro rotary swaging

Micro rotary swaging is a cold forming process for production of micro components with determined geometry and surface. It is also possible to change the microstructure of wires and hence the material properties. Swaging dies revolve around the work piece with an overlaid radial oscillation. Newly developed tools (Flat Surface Dies, FSD) feature plain surfaces and do not represent the geometry of the formed part as in conventional swaging. Using these tools allows for producing wires with triangle geometry (cross section) as well as a circular shape. To test the influence of FSD on material properties by micro swaging a new method is investigated: the variation of the relative speed between the specimen and dies in infeed rotary swaging. During this specific process copper (C11000) and steel (304 Alloy) wires with diameter d0 = 1 mm are formed. It is noticed that the mechanical characteristics such as ductility and strength differ from the characteristics after conventional swaging. Moreover this approach enables new possibilities to influence the geometry and the surface quality of wires. The impact of the relative speed on the processed wire features is described in this paper

2D-simulation of Material Flow During Infeed Rotary Swaging Using Finite Element Method

AbstractFE simulation was applied to study the material flow during infeed rotary swaging. The neutral plane according to the process parameters was investigated and compared with experimental results. A single forming stroke was analyzed precisely by using small time points of 10-4s. For analysis the essential steps between the first contact of wire and forging die and the last contact before the die opens again are represented. In that range the feed velocity is eliminated and the neutral plane can be observed as spatial velocity at nodes in the axial direction equal 0mm/s. During a single stroke the location, the geometry and the orientation of the neutral plane is changing

Eccentric rotary swaging variants

Rotary swaging is an incremental cold forming process that changes beneath the geometry also the microstructure and mechanical properties of workpiece. Especially a new process design with Eccentric Flat Shaped Dies (EFSD) influences both the kind and amount of stress and plastic strain and consequently the material structure and hence the material and workpiece properties. Eccentric rotary swaging typically provides a helical material flow. According to the process parameters the microstructure features a typical eddy pattern with a spiral shaped grain orientation. The forming process can be carried out in one or more process steps. In a multi-stage process, it is possible to change the feed direction and, hence, the material flow helix direction. This approach can be used as a possibility to improve the homogeneity of the workpiece and material properties. In addition, for this aims an intermediate heat treatment in multi-stage forming operations could be realised. Following the goal of optimising the final properties, the question arises how these mechanical and thermal treatments affect the material microstructure and the forming properties of the workpiece and how they interact. Experiments were conducted with austenitic stainless steel rods of grade AISI304. The effects of the varied feed direction, feed velocity and heat treatment between the forming operations are discussed

Eccentric rotary swaging variants

Rotary swaging is an incremental cold forming process that changes beneath the geometry also the microstructure and mechanical properties of workpiece. Especially a new process design with Eccentric Flat Shaped Dies (EFSD) influences both the kind and amount of stress and plastic strain and consequently the material structure and hence the material and workpiece properties. Eccentric rotary swaging typically provides a helical material flow. According to the process parameters the microstructure features a typical eddy pattern with a spiral shaped grain orientation. The forming process can be carried out in one or more process steps. In a multi-stage process, it is possible to change the feed direction and, hence, the material flow helix direction. This approach can be used as a possibility to improve the homogeneity of the workpiece and material properties. In addition, for this aims an intermediate heat treatment in multi-stage forming operations could be realised. Following the goal of optimising the final properties, the question arises how these mechanical and thermal treatments affect the material microstructure and the forming properties of the workpiece and how they interact. Experiments were conducted with austenitic stainless steel rods of grade AISI304. The effects of the varied feed direction, feed velocity and heat treatment between the forming operations are discussed

Generation of residual stresses in rotary swaging process

Infeed rotary swaging is an established incremental cold forming production technique for axisymmetric workpieces. Among others, work hardening as well as near net shape forming are advantages of this production technique. Due to the incremental open die forging process, the rotary swaging induces a complex material flow history which is dependent on the process control. This material flow history influences the material modifications such as work hardening as well as residual stresses. In this study, the properties of steel tubes were investigated after rotary swaging using varying parameters by experimental and simulation analysis. In particular, the influence of lubrication with different feeding velocities was analysed. The workpiece quality, the hardness and the residual stresses were characterized in detail. After rotary swaging, an influence of the process parameters on the geometrical and surface quality could be observed. The workpieces showed significant work hardening which was higher at the surface and process dependent, while below 100 μm, this increased hardness was observed over the complete wall thickness independently of the process parameters. The residual stress state was highly fluctuating at the surface and was in tensile for all conditions. The results showed that the process parameters influenced the properties near the surface, while a few hundred micrometers below the surface, the workpiece properties seemed to be driven only by the total deformation

Generation of residual stresses in rotary swaging process

Infeed rotary swaging is an established incremental cold forming production technique for axisymmetric workpieces. Among others, work hardening as well as near net shape forming are advantages of this production technique. Due to the incremental open die forging process, the rotary swaging induces a complex material flow history which is dependent on the process control. This material flow history influences the material modifications such as work hardening as well as residual stresses. In this study, the properties of steel tubes were investigated after rotary swaging using varying parameters by experimental and simulation analysis. In particular, the influence of lubrication with different feeding velocities was analysed. The workpiece quality, the hardness and the residual stresses were characterized in detail. After rotary swaging, an influence of the process parameters on the geometrical and surface quality could be observed. The workpieces showed significant work hardening which was higher at the surface and process dependent, while below 100 μm, this increased hardness was observed over the complete wall thickness independently of the process parameters. The residual stress state was highly fluctuating at the surface and was in tensile for all conditions. The results showed that the process parameters influenced the properties near the surface, while a few hundred micrometers below the surface, the workpiece properties seemed to be driven only by the total deformation

Eccentric rotary swaging variants

Rotary swaging is an incremental cold forming process that changes beneath the geometry also the microstructure and mechanical properties of the workpiece. Especially a new process design with Eccentric Flat Shaped Dies (EFSD) influences both the kind and amount of stress and plastic strain and consequently the material structure, and hence the material and workpiece properties. Eccentric rotary swaging typically provides a helical material flow. According to the process parameters the microstructure features a typical eddy pattern with a spiral shaped grain orientation. The forming process can be carried out in one or more process steps. In a multistage process, it is possible to change the feed direction and, hence, the material flow helix direction. This approach can be used as a possibility to improve the homogeneity of the workpiece and material properties. In addition, for this aims an intermediate heat treatment in multistage forming operations could be realized. Following the goal of optimizing the final properties, the question arises how these mechanical and thermal treatments affect the material microstructure and the forming properties of the workpiece and how they interact. Experiments were conducted with austenitic stainless steel rods of grade AISI304. The effects of the varied feed direction, feed velocity and heat treatment between the forming operations are discussed

Influence of Process Fluctuations on Residual Stress Evolution in Rotary Swaging of Steel Tubes

Infeed rotary swaging is a cold forming production technique to reduce the diameter of axisymmetric components. The forming is achieved discontinuously by a series of radial strokes that are spread over the shell of the part. Due to tolerances within the rotary swaging machine, these strokes perform individually and the resulting stroke pattern is not homogeneous with regards to circumferential and longitudinal distribution. Nevertheless, in combination with the high number of performed strokes and the large contact area between the dies and the part, the external part properties, such as diameter, roundness and surface roughness, show even values along the finished part. In contrast, strength-defining internal part properties, like microstructure and residual stress components, are more sensitive to the actual pattern and temporal sequence of the individual strokes, which is investigated in this study. The impact of process fluctuations during the conventional process, which are induced by the tolerances of machine tool components, was verified by numerical simulations, physical tests and measurements of residual stress distributions at the surface and at depth. Furthermore, a method is introduced to maintain the stroke following angle ∆φ at zero by flat dies, and thus the actual pattern and temporal sequence of the strokes was homogenized. The results show that the residual stress fluctuations at the surface could be controlled and reduced. Furthermore, it is demonstrated that the depth profile of the residual stresses at a distance of 300 µm from the surface developed independently from the process fluctuations