Influence Of The Electrical Parameters On The Fabrication Of Copper Nanowires Into Anodic Alumina Templates

Metallic copper nanowires have been grown into the pores of alumina membranes by electrodeposition from an aqueous solution containing CuSO4 .and H3BO3 at pH 3. In order to study the influence of the electrical parameters on growth and structure of nanowires, different deposition potentials (both in the region where hydrogen evolution reaction is allowed or not) and voltage perturbation modes (constant potential or unipolar pulsed depositions) were applied. In all cases, pure polycrystalline Cu nanowires were fabricated into template pores, having lengths increasing with the total deposition time. These nanowires were self-standing, because they retain their vertical orientation and parallel geometry even after total template dissolution. However, the electrical parameters influence the growth rate, length uniformity and crystal size of the nanowires. Continuous electrodeposition resulted in higher growth rates but less uniform lengths of nanowires grown inside different membrane pores, whilst a square pulse deposition produced a slower growth but quite uniform lengths. Also the grain size, of the order of 50 nm, was slightly influenced by the potential perturbation mode

Fabrication and Photoelectrochemical Behavior of Ordered CIGS Nanowire Arrays for Application in Solar Cells

In this work, we report some preliminary results concerning the fabrication of quaternary copper, indium, gallium, and selenium CIGS nanowires that were grown inside the channels of an anodic alumina membrane by one-step potentiostatic deposition at different applied potentials and room temperature. A tunable nanowire composition was achieved through a manipulation of the applied potential and electrolyte composition. X-ray diffraction analysis showed that nanowires, whose chemical composition was determined by energy-dispersive spectroscopy analysis, were amorphous. A composition of Cu0.203In0.153Ga0.131Se0.513, very close to the stoichiometric value, was obtained. These nanostructures were also characterized by photoelectrochemical measurements: They showed a cathodic photocurrent and an optical gap of 1.55 eV

Lead Nanowires for Microaccumulators Obtained Through Indirect Electrochemical Template Deposition

Metallic lead nanowires were deposited within pores of commercial anodic alumina membranes having an average pore diameter of 210 nm. “Direct” electrodeposition was attempted from 0.1 M Pb NO3 2 aqueous solution with a variable concentration of H3BO3 as a chelating agent, but it gave unsatisfactory results. An “indirect” two-step deposition procedure was then adopted, consisting of the anodic electrodeposition of -PbO2 nanowires, followed by their in situ reduction to metallic lead. Both these processes occurred at a high rate so that the indirect method led to a complete template pore filling with pure polycrystalline Pb in short times and with a high current efficiency

Electrochemical deposition of CZTS thin films on flexible substrate

Solar cells based on semiconductor thin films are emerging as alternative to silicon;however,the materials giving the highest efficiency,CdTe and CuInGaSe,contain toxic (Cd) and rare (In) elements.In this field,the challenge is to substitute In and Cd with abundant and non-toxic elements without lowering the high efficiency achieved with these technologies.Compounds based on copper,zinc,tin and sulfur (CZTS) are potentially promising materials,because they present all the above listed features.Among the different methods to obtain CZTS,the electrochemical route appears of great interest because easy to conduct.Up to date,the literature shows that non-uniformity in composition and/or the presence of secondary phases prevent the obtainment of electrochemical CZTS thin-film of high quality.In this paper,we present the principal results of an extensive investigations conducted in order to find suitable conditions for growing CZTS thin films with good performance through the simultaneous electrodeposition of elements having different standard electrochemical potentials.Thin films were obtained on a flexible substrate by potentiostatic deposition from aqueous baths by changing different deposition parameters (bath composition and temperature,deposition time).Chemical composition and structure of the electrodeposited films were evaluated by EDS,SEM,RAMAN and XRD.Preliminary results on the photoelectrochemical behaviour of the films will be also presented

One-Step Electrodeposition of CZTS for Solar Cell Absorber Layer

CZTS thin films were obtained by one-step electrochemical deposition from aqueous solution at room temperature. Films were deposited on two different substrates, ITO on PET, and electropolished Mo. Differently from previous studies focusing exclusively on the formation of kesterite (Cu4ZnSnS4), here, the synthesis of a phase with this exact composition was not considered as the unique objective. Really, starting from different baths, amorphous semiconducting layers containing copper–zinc–tin–sulphur with atomic fraction Cu0.592Zn0.124Sn0.063S0.221 and Cu0.415Zn0.061Sn0.349S0.175, were potentiostatically deposited. Due to the amorphous nature, it was not possible to detect if one or more phases were formed. By photoelectrochemical measurements, we evaluated optical gap values between 1.5 eV, similar to that assigned to kesterite, and 1.0 eV. Reproducibility and adhesion to the substrate were solved by changing S with Se. Preliminary results showed that an amorphous p-type layer, having atomic fraction Cu0.434Zn0.036Sn0.138Se0.392 and an optical gap of 1.33 eV, can be obtained by one-step electrochemical deposition

A Multi-Criteria Decision-Making Framework for Zero Emission Vehicle Fleet Renewal Considering Lifecycle and Scenario Uncertainty

In the last decade, with the increased concerns about the global environment, attempts have been made to promote the replacement of fossil fuels with sustainable sources. For transport, which accounts for around a quarter of total greenhouse gas emissions, meeting climate neutrality goals will require replacing existing fleets with electric or hydrogen-propelled vehicles. However, the lack of adequate decision support approach makes the introduction of new propulsion technologies in the transportation sector a complex strategic decision problem where distorted non-optimal decisions may easily result in long-term negative effects on the performance of logistic operators. This research addresses the problem of transport fleet renewal by proposing a multi-criteria decision-making approach and takes into account the multiple propulsion technologies currently available and the objectives of the EU Green Deal, as well as the inherent scenario uncertainty. The proposed approach, based on the TOPSIS model, involves a novel decision framework referred to as a generalized life cycle evaluation of the environmental and cost objectives, which is necessary when comparing green and traditional propulsion systems in a long-term perspective to avoid distorted decisions. Since the objective of the study is to provide a practical methodology to support strategic decisions, the framework proposed has been validated against a practical case referred to the strategic fleet renewal decision process. The results obtained demonstrate how the decision maker's perception of the technological evolution of the propulsion technologies influences the decision process, thus leading to different optimal choices

Electrodeposition from molybdate aqueous solutions: a preliminary study

The electrochemistry of molybdenum (Mo) and its oxides is very important for several applications in electrocatalysis,batteries,sensors and in particular for CIGS-based solar cells,where metal Mo is used as back contact.Properties and the fabrication method of Mo films are of fundamental importance,because they could induce significant changes in solar cell performances.The most important issues in the electrochemical behaviour of Mo are the nature and stability of its surface oxides,which are strongly dependent on deposition bath pH.Ivanova et al. (2006) reported that it is possible to accomplish the cathodic reduction of molybdate ions to metallic Mo from electrolytes containing HF.The addition of this acid selectively prevents the polymerization of MoO42- anions,therefore its concentration plays a fundamental role.A hard drawback connected to deposition in acid media is the strong hydrogen evolution,since H+ reduction is the reaction thermodynamically favoured,therefore it is necessary to apply a very high current density for appreciably depositing Mo.In this work,we report some preliminary results dealing with the electrodeposition process from molybdate aqueous solutions to grow thin films on different substrates and nanowires inside the channels of polycarbonate membranes;electrolyte pH was varied in order to evidence its role on the nature of the deposits,which were characterized by EDS,SEM,RAMAN and XRD analyses

Electrochemical detection of H2O2 by means of gold foam-based electrode

In this work, a low-cost electrochemical sensor was developed for the detection of hydrogen peroxide. Hydrogen peroxide is the most used biomarker in monitoring oxidative stress due to its stability and ability to diffuse across the cell membrane. Oxidative stress occurs when the concentration of reactive oxygen species (ROS) in biological fluids increases with respect to the physiological concentration; this condition is a risk factor for many diseases. Among ROS, hydrogen peroxide is the more stable and thus it can be used as a biomarker. Since oxidative stress is not associated with specific symptoms, it is important to monitor the concentration of hydrogen peroxide to prevent the onset of serious diseases or to slow down their progression. In this field, research aims to develop electrochemical sensors for hydrogen peroxide quantification as an alternative to time-consuming and expensive traditional techniques. The proposed sensor was obtained using the common substrate of the printed circuit board (PCB) fabrication. A design consisting of three electrodes of copper was optimized to obtain a complete cell. The working electrode was modified by electrodeposition to obtain a gold foam. Before gold foam deposition, the copper surface was covered with a thin planar film of gold using sputtering. The foam was electrodeposited by potenziostatic deposition at - 2 V using a water solution containing gold precursor and sulfuric acid. The detection of hydrogen peroxide was carried out with a conventional three-electrode system using a homemade cell obtained by 3D printing. Electrochemical tests were carried out in phosphate buffer as blank and by chronoamperometry at – 0.1 V. To build the calibration line, different concentrations of hydrogen peroxide, ranging from 25 to 1000 μM, were tested. The obtained results showed that the current density was proportional to the concentration of hydrogen peroxide, so the sensor can quantify this analyte. Further study will be addressed to characterize the device in terms of selectivity, stability and reproducibility

Formoterol Exerts Anti-Cancer Effects Modulating Oxidative Stress and Epithelial-Mesenchymal Transition Processes in Cigarette Smoke Extract Exposed Lung Adenocarcinoma Cells

Lung cancer frequently affects patients with Chronic Obstructive Pulmonary Disease (COPD). Cigarette smoke (CS) fosters cancer progression by increasing oxidative stress and by modulating epithelial-mesenchymal transition (EMT) processes in cancer cells. Formoterol (FO), a long-acting β2-agonist widely used for the treatment of COPD, exerts antioxidant activities. This study explored in a lung adenocarcinoma cell line (A549) whether FO counteracted the effects of cigarette smoke extract (CSE) relative to oxidative stress, inflammation, EMT processes, and cell migration and proliferation. A549 was stimulated with CSE and FO, ROS were evaluated by flow-cytometry and by nanostructured electrochemical sensor, EMT markers were evaluated by flow-cytometry and Real-Time PCR, IL-8 was evaluated by ELISA, cell migration was assessed by scratch and phalloidin test, and cell proliferation was assessed by clonogenic assay. CSE significantly increased the production of ROS, IL-8 release, cell migration and proliferation, and SNAIL1 expression but significantly decreased E-cadherin expression. FO reverted all these phenomena in CSE-stimulated A549 cells. The present study provides intriguing evidence that FO may exert anti-cancer effects by reverting oxidative stress, inflammation, and EMT markers induced by CS. These findings must be validated in future clinical studies to support FO as a valuable add-on treatment for lung cancer management