Relationship between casting modulus and grain size in cast A356 aluminium alloys

Microstructure of Al-Si alloy castings depends most generally on melt preparation and on the cooling rate imposed by the thermal modulus of the component. In the case of Al-Si alloys, emphasis is put during melt preparation on refinement of pro-eutectic (Al) grains and on modification of the Al-Si eutectic. Thermal analysis has been used since long to check melt preparation before casting, i.e. by analysis of the cooling curve during solidification of a sample cast in an instrumented cup. The conclusions drawn from such analysis are however valid for the particular cooling conditions of the cups. It thus appeared of interest to investigate how these conclusions could extrapolate to predict microstructure in complicated cast parts showing local changes in the solidification conditions. For that purpose, thermal analysis cups and instrumented sand and die castings with different thermal moduli and thus cooling rates have been made, and the whole set of cooling curves thus recorded has been analysed. A statistical analysis of the characteristic features of the cooling curves related to grain refinement in sand and die castings allowed determining the most significant parameters and expressing the cube of grain size as a polynomial of these parameters. After introduction of a further parameter quantifying melt refining an excellent correlation, with a R2 factor of 0.99 was obtained

Thermodynamic properties of binary HCP solution phases from special quasirandom structures

Three different special quasirandom structures (SQS) of the substitutional hcp $A_{1-x}B_x$ binary random solutions ($x=0.25$, 0.5, and 0.75) are presented. These structures are able to mimic the most important pair and multi-site correlation functions corresponding to perfectly random hcp solutions at those compositions. Due to the relatively small size of the generated structures, they can be used to calculate the properties of random hcp alloys via first-principles methods. The structures are relaxed in order to find their lowest energy configurations at each composition. In some cases, it was found that full relaxation resulted in complete loss of their parental symmetry as hcp so geometry optimizations in which no local relaxations are allowed were also performed. In general, the first-principles results for the seven binary systems (Cd-Mg, Mg-Zr, Al-Mg, Mo-Ru, Hf-Ti, Hf-Zr, and Ti-Zr) show good agreement with both formation enthalpy and lattice parameters measurements from experiments. It is concluded that the SQS's presented in this work can be widely used to study the behavior of random hcp solutions.Comment: 15 pages, 8 figure

Microscopic View on Short-Range Wetting at the Free Surface of the Binary Metallic Liquid Gallium-Bismuth: An X-ray Reflectivity and Square Gradient Theory Study

We present an x-ray reflectivity study of wetting at the free surface of the binary liquid metal gallium-bismuth (Ga-Bi) in the region where the bulk phase separates into Bi-rich and Ga-rich liquid phases. The measurements reveal the evolution of the microscopic structure of wetting films of the Bi-rich, low-surface-tension phase along different paths in the bulk phase diagram. A balance between the surface potential preferring the Bi-rich phase and the gravitational potential which favors the Ga-rich phase at the surface pins the interface of the two demixed liquid metallic phases close to the free surface. This enables us to resolve it on an Angstrom level and to apply a mean-field, square gradient model extended by thermally activated capillary waves as dominant thermal fluctuations. The sole free parameter of the gradient model, i.e. the so-called influence parameter, $\kappa$, is determined from our measurements. Relying on a calculation of the liquid/liquid interfacial tension that makes it possible to distinguish between intrinsic and capillary wave contributions to the interfacial structure we estimate that fluctuations affect the observed short-range, complete wetting phenomena only marginally. A critical wetting transition that should be sensitive to thermal fluctuations seems to be absent in this binary metallic alloy.Comment: RevTex4, twocolumn, 15 pages, 10 figure

Patterns and Predictors of Service Use Among Women Who Have Separated from an Abusive Partner

# The Author(s) 2015. This article is published with open access at Springerlink.com Abstract Using baseline data from a survey of 309 Canadian women recently separated from an abusive partner, we inves-tigated patterns of access to health, social, legal, and violence-specific services and whether abuse history and social and health variables predict service use. We compared rates of service use to population rates, and used logistic regression to identify determinants of use. Service use rates were sub-stantially higher than population estimates in every category, particularly in general and mental health sectors. Although women were confident in their ability to access services, they reported substantial unmet need, difficulty accessing services, and multiple barriers. The strongest unique predictors of use varied across service type. Health variables (high disability chronic pain, symptoms of depression and PTSD), low in