29,457 research outputs found
Testrun results from prototype fiber detectors for high rate particle tracking
A fiber detector concept has been realized allowing to registrate particles
within less than 100 nsec with a space point precision of about 0.1 mm at low
occupancy. Three full size prototypes have been build by different producers
and tested at a 3 GeV electron beam at DESY. After 3 m of light guides 8-10
photoelectrons were registrated by multichannel photomultipliers providing an
efficiency of more than 99%. Using all available data a resolution of 0.086 mm
was measured.Comment: 18 pages, 17 figure
Enhancement of perfluorooctanoate and perfluorooctanesulfonate activity at acoustic cavitation bubble interfaces
Acoustic cavitation driven by ultrasonic irradiation decomposes and mineralizes the recalcitrant perfluorinated surfactants perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA). Pyrolytic cleavage of the ionic headgroup is the rate-determining step. In this study, we examine the sonochemical adsorption of PFOX, where X = S for PFOS and A for PFOA, by determining kinetic order and absolute rates over an initial PFOX concentration range of 20 nM to 200 μM. Sonochemical PFOX kinetics transition from pseudo-first-order at low initial concentrations, [PFOX]_i 40 μM, as the bubble interface sites are saturated. At PFOX concentrations below 100 μM, concentration-dependent rates were modeled with Langmuir−Hinshelwood (LH) kinetics. Empirically determined rate maximums, V_(Max)^(−PFOA) = 2230 ± 560 nM min^−1 and V_(Max)^(−PFOS) = 230 ± 60 nM min^−1, were used in the LH model, and sonochemical surface activities were estimated to be K_(Sono)^(PFOS) = 120000 M^−1 and K_(Sono)^(PFOA) = 28500 M^−1, 60 and 80 times greater than equilibrium surface activities, K_(Eq)^(PFOS) and K_(Eq)^(PFOA). These results suggest enhanced sonochemical degradation rates for PFOX when the bubble interface is undersaturated. The present results are compared to previously reported sonochemical kinetics of nonvolatile surfactants
Instrument to collect fogwater for chemical analysis
An instrument is presented which collects large samples of ambient fogwater by impaction of droplets on a screen. The collection efficiency of the instrument is determined as a function of droplet size, and it is shown that fog droplets in the range 3–100-µm diameter are efficiently collected. No significant evaporation or condensation occurs at any stage of the collection process. Field testing indicates that samples collected are representative of the ambient fogwater. The instrument may easily be automated, and is suitable for use in routine air quality monitoring programs
Methods to Determine Total Electron-Induced Electron Yields Over Broad Range ofConductive and Nonconductive Materials
The electron emission properties of a material subject to incident radiation flux are key parameters in determining to what equilibrium charge a spacecraft will established under given environmental conditions. However, there is a complex relation between these emission properties and the charge built up in spacecraft insulators. Complex modeling codes have been developed to predict the potential a spacecraft will adopt as a consequence of its interaction with the space plasma. These require correct models of the electron yields as a function of charge to accurately predict the both the charge build up and the equilibrium potential of spacecraft components.
This paper focuses on different methods appropriate to determine the fundamental electronic material property of total electron yield as the materials accumulates charge. Three methods for determining the uncharged total yield are presented: (i) The DC Continuous Beam Method is a relatively easy and accurate method appropriate for conductors and semi- conductors with maximum total electron yield σmaxρ\u3c106 \u3eΩ-cm.
(ii) The Pulse-Yield Method seeks to minimize the effects of charging and is applicable to materials with σmaxρ up to \u3e1024 Ω-cm. (iii) The Yield Decay Method is a very difficult and time consuming that uses a combination of measurement and modeling to measure the most difficult materials with σmax\u3e4 and ρ up to \u3e1024 Ω-cm.
Data for high purity polycrystalline Au, Kapton HN, and polycrystalline aluminum oxide ceramic are presented. These data demonstrate the relative strengths and weaknesses of each method, but more importantly show that the methods described herein are capable of reliably measuring the total electron yield of almost any spacecraft material
Hybrid phase-space simulation method for interacting Bose fields
We introduce an approximate phase-space technique to simulate the quantum
dynamics of interacting bosons. With the future goal of treating Bose-Einstein
condensate systems, the method is designed for systems with a natural
separation into highly occupied (condensed) modes and lightly occupied modes.
The method self-consistently uses the Wigner representation to treat highly
occupied modes and the positive-P representation for lightly occupied modes. In
this method, truncation of higher-derivative terms from the Fokker-Planck
equation is usually necessary. However, at least in the cases investigated
here, the resulting systematic error, over a finite time, vanishes in the limit
of large Wigner occupation numbers. We tested the method on a system of two
interacting anharmonic oscillators, with high and low occupations,
respectively. The Hybrid method successfully predicted atomic quadratures to a
useful simulation time 60 times longer than that of the positive-P method. The
truncated Wigner method also performed well in this test. For the prediction of
the correlation in a quantum nondemolition measurement scheme, for this same
system, the Hybrid method gave excellent agreement with the exact result, while
the truncated Wigner method showed a large systematic error.Comment: 13 pages; 6 figures; references added; figures correcte
- …