Development of high critical current density in multifilamentary round-wire Bi2Sr2CaCu2O8+x by strong overdoping

Bi2Sr2CaCu2O8+x is the only cuprate superconductor that can be made into a round-wire conductor form with a high enough critical current density Jc for applications. Here we show that the Jc(5 T,4.2 K) of such Ag-sheathed filamentary wires can be doubled to more than 1.4x10^5 A/cm^2 by low temperature oxygenation. Careful analysis shows that the improved performance is associated with a 12 K reduction in transition temperature Tc to 80 K and a significant enhancement in intergranular connectivity. In spite of the macroscopically untextured nature of the wire, overdoping is highly effective in producing high Jc values.Comment: 4 figure

Disorder effects on the superconducting properties of BaFe1.8_{1.8}Co0.2_{0.2}As2_2 single crystals

Single crystals of superconducting BaFe$_{1.8}$Co$_{0.2}$As$_2$ were exposed to neutron irradiation in a fission reactor. The introduced defects decrease the superconducting transition temperature (by about 0.3 K) and the upper critical field anisotropy (e.g. from 2.8 to 2.5 at 22 K) and enhance the critical current densities by a factor of up to about 3. These changes are discussed in the context of similar experiments on other superconducting materials

Atmospheric conditions and their effect on ball-milled magnesium diboride

Magnesium diboride bulk pellets were fabricated from pre-reacted MgB2 powder ball milled with different amounts of exposure to air. Evidence of increased electron scattering including increased resistivity, depressed Tc, and enhanced Hc2 of the milled and heat treated samples were observed as a result of increased contact with air. These and other data were consistent with alloying with carbon as a result of exposure to air. A less clear trend of decreased connectivity associated with air exposure was also observed. In making the case that exposure to air should be considered a doping process, these results may explain the wide varibability of "undoped" MgB2 properties extant in the literature.Comment: Work presented at ASC 2006 in Seattl

A Trapped Field of 17.6 T in Melt-Processed, Bulk Gd-Ba-Cu-O Reinforced with Shrink-Fit Steel

The ability of large grain, REBa$_{2}$Cu$_{3}$O$_{7-\delta}$ [(RE)BCO; RE = rare earth] bulk superconductors to trap magnetic field is determined by their critical current. With high trapped fields, however, bulk samples are subject to a relatively large Lorentz force, and their performance is limited primarily by their tensile strength. Consequently, sample reinforcement is the key to performance improvement in these technologically important materials. In this work, we report a trapped field of 17.6 T, the largest reported to date, in a stack of two, silver-doped GdBCO superconducting bulk samples, each of diameter 25 mm, fabricated by top-seeded melt growth (TSMG) and reinforced with shrink-fit stainless steel. This sample preparation technique has the advantage of being relatively straightforward and inexpensive to implement and offers the prospect of easy access to portable, high magnetic fields without any requirement for a sustaining current source.Comment: Updated submission to reflect licence change to CC-BY. This is the "author accepted manuscript" and is identical in content to the published versio

New U-Th Dates from Vindija, Velika pećina (Kličevica) and Mujina pećina and Their Implications for Chronology of the Middle Paleolithic in Croatia

This paper reports new results obtained by Uranium-Thorium (U-Th) dating of animal bones, tooth and flowstone samples from three Croatian Middle Paleolithic sites. Dates were obtained on bones and teeth from Vindija (Hrvatsko zagorje) and flowstones from Velika pećina in Kličevica and Mujina pećina (both in Dalmatia). Obtained results support the previously established chronology of the Middle Paleolithic of Croatia by confirming that the oldest layers of Vindija belong to MIS 6 and that Velika pećina in Kličevica was visited by Neandertals after 40 ka BP

Electrodynamics of superconducting pnictide superlattices

It has been recently reported (S. Lee et al., Nature Materials 12, 392, 2013) that superlattices where layers of the 8% Co-doped BaFe2As2 superconducting pnictide are intercalated with non superconducting ultrathin layers of either SrTiO3 or of oxygen-rich BaFe2As2, can be used to control flux pinning, thereby increasing critical fields and currents, without significantly affecting the critical temperature of the pristine superconducting material. However, little is known about the electron properties of these systems. Here we investigate the electrodynamics of these superconducting pnictide superlattices in the normal and superconducting state by using infrared reflectivity, from THz to visible range. We find that multi-gap structure of these superlattices is preserved, whereas some significant changes are observed in their electronic structure with respect to those of the original pnictide. Our results suggest that possible attempts to further increase the flux pinning may lead to a breakdown of the pnictide superconducting properties.Comment: 4 pages, two figure

Nanoscale grains, high irreversibility field, and large critical current density as a function of high energy ball milling time in C-doped magnesium diboride

Magnesium diboride (MgB2) powder was mechanically alloyed by high energy ball milling with C to a composition of Mg(B0.95C0.05)2 and then sintered at 1000 C in a hot isostatic press. Milling times varied from 1 minute to 3000 minutes. Full C incorporation required only 30-60 min of milling. Grain size of sintered samples decreased with increased milling time to less than 30 nm for 20-50 hrs of milling. Milling had a weak detrimental effect on connectivity. Strong irreversibility field (H*) increase (from 13.3 T to 17.2 T at 4.2 K) due to increased milling time was observed and correlated linearly with inverse grain size (1/d). As a result, high field Jc benefited greatly from lengthy powder milling. Jc(8 T, 4.2 K) peaked at > 80,000 A/cm2 with 1200 min of milling compared with only ~ 26,000 A/cm2 for 60 min of milling. This non-compositional performance increase is attributed to grain refinement of the unsintered powder by milling, and to the probable suppression of grain growth by milling-induced MgO nano-dispersions.Comment: 12 pages, 11 figure