Dynamic Load and Storage Integration

Modern technology combined with the desire to minimize the size and weight of a ship’s power system are leading to renewed interest in more electric or all electric ships. An important characteristic of the emerging ship power system is an increasing level of load variability, with some future pulsed loads requiring peak power in excess of the available steady– state power. This inevitably leads to the need for some additional energy storage beyond that inherent in the fuel. With the current and evolving technology, it appears that storage will be in the form of batteries, rotating machines, and capacitors. All of these are in use on ships today and all have enjoyed significant technological improvements over the last decade. Moreover all are expected to be further enhanced by today’s materials research. A key benefit of storage is that, when it can be justified for a given load, it can have additional beneficial uses such as ride-through capability to restart a gas turbine if there is an unanticipated power loss; alternatively, storage can be used to stabilize the power grid when switching large loads. Knowing when to stage gas turbine utilization versus energy storage is a key subject in this paper. The clear need for storage has raised the opportunity to design a comprehensive storage system, sometimes called an energy magazine, that can combine intermittent generation as well as any or all of the other storage technologies to provide a smaller, lighter and better performing system than would individual storage solutions for each potential application.Center for Electromechanic

Waveform-level time-domain simulation comparison study of three shipboard power system architectures

Detailed waveform-level modeling and simulation of three alternative shipboard power system architectures is presented herein. The three system architectures are based on conventional 60Hz medium-voltage ac (MVAC), higherfrequency 240Hz medium-voltage ac (HFAC) and mediumvoltage dc (MVDC) technologies. To support the quantitative assessment and comparison of these three different power system architectures, each technology was modeled using a common representative, notional baseline ship. The baseline ship represents a multi-mission destroyer fitted with an 80MW next generation integrated power system (NGIPS). Modeling of each power system architecture is set forth along with simulation studies for three fault scenarios. Each of the three power system architectures was implemented within the MATLAB/ Simulink environment. Continuity of service was evaluated for each architecture along with a fault scenario using an operability metric. After a brief description of the three power system architectures and the operability metric, quantitative results are presented.Center for Electromechanic

Analysis of the Power Quality Impact of Multiple Directed Energy Loads on an Electric Ship Power System

The electrical power system of an all-electric ship has been modeled in Simulink for the case of a ship supporting several high power directed energy loads, among which are a Free Electron Laser (FEL), an Active Denial System (ADS), and a Laser Weapon System (LaWS). Starting from a load centered approach, and a physical description of the components of the various loads, individual models of each load plus a combined model for a system supporting simultaneously one instance of all loads have been developed. Sample case studies are presented corresponding to expected operational scenarios for a US Navy ship and to potential emergency conditions. The models have been designed to be interactive, allowing the operator to change key settings dynamically while the simulation is running, thus mimicking an actual operation of the power system on a ship in real time. A preliminary graphical user interface has also been developed to demonstrate the ability of these models to be converted into top-level training tools for Navy personnel supported by a realistic representation of the ship power system

Large Scale Simulations of a Ship Power System with Energy Storage and Multiple Directed Energy Loads

A large scale Simulink® simulation model of the electrical power system of a ship is described. The model includes the major systems onboard, from prime movers to the actual loads, and incorporates several intermittent duty loads along with continuous duty loads. Three types of energy storage systems have been modeled: flywheels, batteries, and capacitors. Therefore, critical issues like stability, reconfigurability, fault management, and minimum rating of energy storage units can be studied. The presence of energy storage has also allowed the study of how these systems can be used to improve the overall performance of the ship. Typical functions, for example, would include load leveling of the power bus, an uninterruptible power supply function for sections of the ship, and the potential for fuel efficiency improvement by reducing the number of turbines being run at fractional loads to fewer being run closer to their optimal specific fuel efficiency point. Typical outputs of the simulations are presented and discussed. In addition, several challenges presented by the scale of the simulations, the software platform used, and the underlying modeling philosophy are discussed with an outlook toward future improvements both in the computing hardware and in the programming methods.Center for Electromechanic

Power System and Energy Storage Models for Laser Integration on Naval Platforms

High power solid state laser systems are being developed for advanced weapons and sensors for a variety of Department of Defense applications including naval surface combatants. The transient power and cooling requirements of these emerging technologies present significant challenges to the electric power distribution and thermal management systems, particularly for applications requiring back fit of the new systems onto existing platforms with limited electric power generation and cooling capacities.Center for Electromechanic

The Gaseous Electronics Conference radio‐frequency reference cell: A defined parallel‐plate radio‐frequency system for experimental and theoretical studies of plasma‐processing discharges

A ‘‘reference cell’’ for generating radio‐frequency (rf) glow discharges in gases at a frequency of 13.56 MHz is described. The reference cell provides an experimental platform for comparing plasma measurements carried out in a common reactor geometry by different experimental groups, thereby enhancing the transfer of knowledge and insight gained in rf discharge studies. The results of performing ostensibly identical measurements on six of these cells in five different laboratories are analyzed and discussed. Measurements were made of plasma voltage and current characteristics for discharges in pure argon at specified values of applied voltages, gas pressures, and gas flow rates. Data are presented on relevant electrical quantities derived from Fourier analysis of the voltage and current wave forms. Amplitudes, phase shifts, self‐bias voltages, and power dissipation were measured. Each of the cells was characterized in terms of its measured internal reactive components. Comparing results from different cells provides an indication of the degree of precision needed to define the electrical configuration and operating parameters in order to achieve identical performance at various laboratories. The results show, for example, that the external circuit, including the reactive components of the rf power source, can significantly influence the discharge. Results obtained in reference cells with identical rf power sources demonstrate that considerable progress has been made in developing a phenomenological understanding of the conditions needed to obtain reproducible discharge conditions in independent reference cells.Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/70394/2/RSINAK-65-1-140-1.pd

Electrical Network-Based Time-Dependent Model of Electrical Breakdown in Water

A time-dependent, two-dimensional, percolative approach to model dielectric breakdown based on a network of parallel resistor–capacitor elements having random values, has been developed. The breakdown criteria rely on a threshold electric field and on energy dissipation exceeding the heat of vaporization. By carrying out this time-dependent analysis, the development and propagation of streamers and prebreakdown dynamical evolution have been obtained directly. These model simulations also provide the streamer shape, characteristics such as streamer velocity, the prebreakdown delay time, time-dependent current, and relationship between breakdown times, and applied electric fields for a given geometry. The results agree well with experimental data and reports in literature. The time to breakdown (tbr) for a 100 μm water gap has been shown to be strong function of the applied bias, with a 15–185 ns range. It is also shown that the current is fashioned not only by dynamic changes in local resistance, but that capacitive modifications arising from vaporization and streamer development also affect the transient behavior

Inkjet Metrology: High-Accuracy Mass Measurements of Microdroplets Produced by a Drop-on-Demand Dispenser

We describe gravimetric methods for measuring the mass of droplets generated by a drop-on-demand (DOD) microdispenser. Droplets are deposited, either continuously at a known frequency or as a burst of known number, into a cylinder positioned on a submicrogram balance. Mass measurements are acquired precisely by computer, and results are corrected for evaporation. Capabilities are demonstrated using isobutyl alcohol droplets. For ejection rates greater than 100 Hz, the repeatability of droplet mass measurements was 0.2%, while the combined relative standard uncertainty (uc) was 0.9%. When bursts of droplets were dispensed, the limit of quantitation was 72 μg (1490 droplets) with uc = 1.0%. Individual droplet size in a burst was evaluated by high-speed videography. Diameters were consistent from the tenth droplet onward, and the mass of an individual droplet was best estimated by the average droplet mass with a combined uncertainty of about 1%. Diameters of the first several droplets were anomalous, but their contribution was accounted for when dispensing bursts. Above the limits of quantitation, the gravimetric methods provided statistically equivalent results and permit detailed study of operational factors that influence droplet mass during dispensing, including the development of reliable microassays and standard materials using DOD technologies

Zinc Coordination Is Required for and Regulates Transcription Activation by Epstein-Barr Nuclear Antigen 1

Epstein-Barr Nuclear Antigen 1 (EBNA1) is essential for Epstein-Barr virus to immortalize naïve B-cells. Upon binding a cluster of 20 cognate binding-sites termed the family of repeats, EBNA1 transactivates promoters for EBV genes that are required for immortalization. A small domain, termed UR1, that is 25 amino-acids in length, has been identified previously as essential for EBNA1 to activate transcription. In this study, we have elucidated how UR1 contributes to EBNA1's ability to transactivate. We show that zinc is necessary for EBNA1 to activate transcription, and that UR1 coordinates zinc through a pair of essential cysteines contained within it. UR1 dimerizes upon coordinating zinc, indicating that EBNA1 contains a second dimerization interface in its amino-terminus. There is a strong correlation between UR1-mediated dimerization and EBNA1's ability to transactivate cooperatively. Point mutants of EBNA1 that disrupt zinc coordination also prevent self-association, and do not activate transcription cooperatively. Further, we demonstrate that UR1 acts as a molecular sensor that regulates the ability of EBNA1 to activate transcription in response to changes in redox and oxygen partial pressure (pO2). Mild oxidative stress mimicking such environmental changes decreases EBNA1-dependent transcription in a lymphoblastoid cell-line. Coincident with a reduction in EBNA1-dependent transcription, reductions are observed in EBNA2 and LMP1 protein levels. Although these changes do not affect LCL survival, treated cells accumulate in G0/G1. These findings are discussed in the context of EBV latency in body compartments that differ strikingly in their pO2 and redox potential