Tall Fescue for Trouble Spots

Livestock don\u27t like this new grass too well. It won\u27t take the place of our popular pasture plants. But there\u27s a specialized use for tall fescue on many Iowa farms

Emerald Crownvetch - a pasture legume

Used up to now primarily for erosion control on steep high-way banks, Emerald Crownvetch has stood up under sustained grazing and shows promise as a pasture legume on soils not well suited for birdsfoot trefoil

Mixing of Supersonic Streams

The Strutjet approach to Rocket Based Combined Cycle (RBCC) propulsion depends upon fuel-rich flows from the rocket nozzles and turbine exhaust products mixing with the ingested air for successful operation in the ramjet and scramjet modes. It is desirable to delay this mixing process in the air-augmented mode of operation present during low speed flight. A model of the Strutjet device has been built and is undergoing test to investigate the mixing of the streams as a function of distance from the Strutjet exit plane during simulated low speed flight conditions. Cold flow testing of a 1/6 scale Strutjet model is underway and nearing completion. Planar Laser Induced Fluorescence (PLIF) diagnostic methods are being employed to observe the mixing of the turbine exhaust gas with the gases from both the primary rockets and the ingested air simulating low speed, air augmented operation of the RBCC. The ratio of the pressure in the turbine exhaust duct to that in the rocket nozzle wall at the point of their intersection is the independent variable in these experiments. Tests were accomplished at values of 1.0, 1.5 and 2.0 for this parameter. Qualitative results illustrate the development of the mixing zone from the exit plane of the model to a distance of about 10 rocket nozzle exit diameters downstream. These data show the mixing to be confined in the vertical plane for all cases, The lateral expansion is more pronounced at a pressure ratio of 1.0 and suggests that mixing with the ingested flow would be likely beginning at a distance of 7 nozzle exit diameters downstream of the nozzle exit plane

Study of Deposition Methods for Silicon Powder

Silicon powder tends to agglomerate at normal atmospheric conditions and is, hence, difficult to aerosolize. Several methods of aerosolizing silicon powder and finally depositing it on various substrates were investigated. This paper presents the investigated methods of aerosolization. The electrostatic spray coating used in dry paint application was found to be the most suitable. The general merits of this method and its use for silicon powder deposition to form films are discussed

Low-Cost Flow Visualization for a Supersonic Ejector

Shadowgraph techniques were applied to the cold flow ejector facility at the Propulsion Research Center at the University of Alabama in Huntsville. The setup for the experiments was relatively simple and was accomplished at very little cost. Series of shadowgraph images were taken of both dual nozzle and single nozzle strut based ejectors operating over a range of chamber pressures. The density gradient patterns in the shadowgraphs were compared to pressure data measured along the top and side walls of the mixing duct. The shadowgraph images showed the presence of barrel shocks emanating from the nozzles which at low pressures terminated in Mach disks and at higher pressures extended beyond the barrel shape and reflected off the walls of the duct. Based on pressure data from previous testing, reflected shocks were expected on the walls of the duct. The shadowgraph images confirmed the locations of these reflected shocks on the top wall of the duct. The shadowgraph images also showed the structure change which correlated to a change in pitch of the ejector noise, and corresponded to a change in trend of the duct wall pressure ratio distributions. The images produced from the setup provided insight into the complex flow behavior inside the ejector duct. In addition, the techniques were a valuable tool as an educational device for students

Constant amplitude and post-overload fatigue crack growth behavior in PM aluminum alloy AA 8009

A recently developed, rapidly solidified, powder metallurgy, dispersion strengthened aluminum alloy, AA 8009, was fatigue tested at room temperature in lab air. Constant amplitude/constant delta kappa and single spike overload conditions were examined. High fatigue crack growth rates and low crack closure levels compared to typical ingot metallurgy aluminum alloys were observed. It was proposed that minimal crack roughness, crack path deflection, and limited slip reversibility, resulting from ultra-fine microstructure, were responsible for the relatively poor da/dN-delta kappa performance of AA 8009 as compared to that of typical IM aluminum alloys

Evaluation of Iowa Stiff Stalk Synthetic for resistance to gray leaf spot

Gray leaf spot (GLS) of maize (Zeamays), caused by Cercospora zeae-maydis, has become an increasing disease problem in the United States. Resistance to this pathogen is generally higher in inbred lines of Lancaster origin compared to lines derived from Iowa Stiff Stalk Synthetic (BSSS). This study was conducted to determine whether recurrent selection for yield had altered the level of GLS resistance in BSSS and to identify BSSS(R)Cl 1 S1 lines that combine GLS resistance with high yield. The distribution of GLS ratings for S1 lines derived from BSSSCO and BSSS(R)CI I were very similar, indicating that selection for yield had not altered G LS resistance· levels. Although the mean rating for both cycles was a susceptible 7 (I= resistant, 9 =susceptible), S1 lines with intermediate levels of resistance (4-6) were identified. The 250 BSSS(R)Cl I S1 lines were crossed to LH51, and the testcrosses were evaluated for yield and agronomic performance. S1 lines were identified which combine intermediate levels of GLS resistance with above-average standability and yield. These S1 lines will be recombined to develop an Iowa Stiff Stalk Synthetic population adapted to eastern maize growing conditions