Enhancement of the photoelectric performance of dye-sensitized solar cells using Ag-doped TiO2 nanofibers in a TiO2 film as electrode

For high solar conversion efficiency of dye-sensitized solar cells [DSSCs], TiO2 nanofiber [TN] and Ag-doped TiO2 nanofiber [ATN] have been extended to be included in TiO2 films to increase the amount of dye loading for a higher short-circuit current. The ATN was used on affected DSSCs to increase the open circuit voltage. This process had enhanced the exit in dye molecules which were rapidly split into electrons, and the DSSCs with ATN stop the recombination of the electronic process. The conversion efficiency of TiO2 photoelectrode-based DSSCs was 4.74%; it was increased to 6.13% after adding 5 wt.% ATN into TiO2 films. The electron lifetime of DSSCs with ATN increased from 0.29 to 0.34 s and that electron recombination was reduced

Increases in solar conversion efficiencies of the ZrO2 nanofiber-doped TiO2 photoelectrode for dye-sensitized solar cells

In this paper, in order to improve the efficiency of dye-sensitized solar cells, we introduced zirconia [ZrO2] nanofibers into a mesoporous titania [TiO2] photoelectrode. The photoelectrode consists of a few weight percent of ZrO2 nanofibers and a mesoporous TiO2 powder. The mixed ZrO2 nanofibers and the mesoporous TiO2 powder possessed a larger surface area than the corresponding mesoporous TiO2 powder. The optimum ratio of the ZrO2 nanofiber was 5 wt.%. The 5 wt.% ZrO2-mixed device could get a short-circuit photocurrent density of 15.9 mA/cm2, an open-circuit photovoltage of 0.69 V, a fill factor of 0.60, and a light-to-electricity conversion efficiency of 6.5% under irradiation of AM 1.5 (100 mW/cm2)

Performance Improvement of Dye-Sensitized Glass Powder Added TiO(2) Solar Cells

The effect of two different types of glass powder added TiO(2) hydride photoelectrode in performance of dye sensitize solar cell (DSSC) had been studied at different wt.%. TiO(2) particles diffusion and possible attachment with Si atoms was observed with field-emission scanning electron microscopy (FE-SEM) and it strongly depends on characteristics of glass. Short circuit current (l(sc)) was increased with increasing the wt.% up to 5% of glass powder and further increase in wt.% ratio had decreased the l(sc). Maximum increase upto 32 and 45% in the efficiently was observed at 5 wt.% of glass powder in TiO(2) for low temperature (LTG) and high temperature glass (HTG) powder, respectively. Adding glass powder in TiO(2) can increase light scattering properties of hybrid electrode and can also create an energy barriers of SiO(2) which prevents the recombination reactions, hence; an increase in efficiency observed

THE ELECTROCHEMICAL PROPERTIES OF Li/FeS BATTERY USING ELECTROLESS NICKEL PLATED FeS POWDER

In order to investigate the electrochemical properties of Li/FeS cell, FeS powder was fabricated by using a high-energy ball milling method. Then, surface of FeS powder was coated with metallic nickel. Nickel coating was conducted by using electroless nickel plating method. Nickel chloride (NiCl2 · 6H2O) was used as the nickel ion source for electroless nickel plating. The effects of nickel coating on the electrochemical properties of FeS electrode for Li/FeS cell were investigated by CV measurement and charge/discharge tests. Then, cells for electrochemical tests were assembled by stacking a lithium anode, separator containing liquid electrolyte, and FeS cathode in turn. From the results, electroless nickel plated FeS electrode showed very high initial discharge capacity of 581 mAh/g-FeS. And also, it showed higher discharge capacity than that of bare FeS electrode until the 29th cycle. Therefore, it is found that metallic nickel gives beneficial effects on enhancing the electrical conductivity of FeS cathode material. 82.47.Cb.Electroless plating, Li/FeS battery, iron sulfide

Preparation and Characterization of Chitosan Binder-Based Electrode for Dye-Sensitized Solar Cells

A chitosan binder-based TiO2 photoelectrode is used in dye-sensitized solar cells (DSSCs). Field-emission scanning electron microscope (FE-SEM) images revealed that the grain size, thickness, and distribution of TiO2 films are affected by the chitosan content. With addition of 2.0 wt% chitosan to the TiO2 film (D2), the surface pore size became the smallest, and the pores were fairly evenly distributed. The electron transit time, electron recombination lifetime, diffusion coefficient, and diffusion length were analyzed by IMVS and IMPS. The best DSSC, with 2.0 wt% chitosan addition to the TiO2 film, had a shorter electron transit time, longer electron recombination lifetime, and larger diffusion coefficient and diffusion length than the other samples. The results of 2.0 wt% chitosan-added TiO2 DSSCs are an electron transit time of  s, electron recombination lifetime of  s, diffusion coefficient of  cm2 s−1, diffusion length of 14.81 μm, and a solar conversion efficiency of 4.18%