19,468 research outputs found
Planar Superconductor-Normal-Superconductor Josephson Junctions in MgB2
Since the discovery of superconductivity in MgB2 considerable progress has
been made in determining the physical properties of the material, which are
promising for bulk conductors. Tunneling studies show that the material is
reasonably isotropic and has a well-developed s-wave energy gap (∆),
implying that electronic devices based on MgB2 could operate close to 30K.
Although a number of groups have reported the formation of thin films by
post-reaction of precursors, heterostructure growth is likely to require
considerable technological development, making single-layer device structures
of most immediate interest. MgB2 is unlike the cuprate superconductors in that
grain boundaries do not form good Josephson junctions, and although a SQUID
based on MgB2 nanobridges has been fabricated, the nanobridges themselves do
not show junction-like properties. Here we report the successful creation of
planar MgB2 junctions by localised ion damage in thin films. The critical
current (IC) of these devices is strongly modulated by applied microwave
radiation and magnetic field. The product of the critical current and normal
state resistance (ICRN) is remarkably high, implying a potential for very high
frequency applications.Comment: 7 pages including 4 figure
Low-velocity anisotropic Dirac fermions on the side surface of topological insulators
We report anisotropic Dirac-cone surface bands on a side-surface geometry of
the topological insulator BiSe revealed by first-principles
density-functional calculations. We find that the electron velocity in the
side-surface Dirac cone is anisotropically reduced from that in the
(111)-surface Dirac cone, and the velocity is not in parallel with the wave
vector {\bf k} except for {\bf k} in high-symmetry directions. The size of the
electron spin depends on the direction of {\bf k} due to anisotropic variation
of the noncollinearity of the electron state. Low-energy effective Hamiltonian
is proposed for side-surface Dirac fermions, and its implications are presented
including refractive transport phenomena occurring at the edges of tological
insulators where different surfaces meet.Comment: 4 pages, 2 columns, 4 figure
Recommended from our members
Intumescent Flame Retardant Polyamide 11 Nanocomposites
Current polyamide 11 and 12 are lacking in fire retardancy and high strength/high heat
resistance characteristics for a plethora of fabricated parts that are desired and required
for performance driven applications. The introduction of selected nanoparticles such as
surface modified montmorillonite (MMT) clay or carbon nanofibers (CNFs), combined
with a conventional intumescent flame retardant (FR) additive into the polyamide
11/polyamide 12 (PA11/PA12) by melt processing conditions has resulted in the
preparation of a family of intumescent polyamide nanocomposites. These intumescent
polyamide 11 and 12 nanocomposites exhibit enhanced polymer performance
characteristics, i.e., fire retardancy, high strength and high heat resistance and are
expected to expand the market opportunities for polyamide 11 and polyamide 12 polymer
manufacturers.
The objective of this research is to develop improved polyamide 11 and 12 polymers with
enhanced flame retardancy, thermal, and mechanical properties for selective laser
sintering (SLS) rapid manufacturing (RM). In the present study, a nanophase was
introduced into the polyamide 11 and combining it with a conventional intumescent FR
additive via twin screw extrusion. Arkema RILSAN® polyamide 11 molding polymer
pellets were examined with two types of nanoparticles: chemically modified
montmorillonite (MMT) organoclays, and carbon nanofibers (CNFs); and Clairant’s
Exolit® OP 1230 intumescent FR additive were used to create a family of FR
intumescent polyamide 11 nanocomposites.
Transmission electron microscopy (TEM) was used to determine the degree of
nanoparticles dispersion. Injection molded specimens were fabricated for physical,
thermal, and flammability measurements. Thermal stability of these intumescent
polyamide 11 nanocomposites was examined by TGA. Flammability properties were
obtained using the Cone Calorimeter at an external heat flux of 35 kW/m
2
and UL 94
Test Method. Heat deflection temperatures (HDT) were also measured. TEM
micrographs, physical, thermal, and flammability properties are presented. FR
intumescent polyamide 11 nanocomposites properties are compared with polyamide 11
baseline polymer. Based on flammability and mechanical material performance, selective
polymers including polyamide 11 nanocomposites and control polyamide 11 will be
cryogenically ground into fine powders for SLS RM processing. SLS specimens will be
fabricated for thermal, flammability, and mechanical properties characterization.Mechanical Engineerin
Time-delayed Spatial Patterns in a Two-dimensional Array of Coupled Oscillators
We investigated the effect of time delays on phase configurations in a set of
two-dimensional coupled phase oscillators. Each oscillator is allowed to
interact with its neighbors located within a finite radius, which serves as a
control parameter in this study. It is found that distance-dependent
time-delays induce various patterns including traveling rolls, square-like and
rhombus-like patterns, spirals, and targets. We analyzed the stability
boundaries of the emerging patterns and briefly pointed out the possible
empirical implications of such time-delayed patterns.Comment: 5 Figure
Thermodynamic Phase Diagram of the Quantum Hall Skyrmion System
We numerically study the interacting quantum Hall skyrmion system based on
the Chern-Simons action. By noticing that the action is invariant under global
spin rotations in the spin space with respect to the magnetic field direction,
we obtain the low-energy effective action for a many skyrmion system.
Performing extensive molecular dynamics simulations, we establish the
thermodynamic phase diagram for a many skyrmion system.Comment: 4 pages, RevTex, 2 postscript figure
Selective copper extraction by multi-modified mesoporous silica material, SBA-15
© 2018 Selective copper (Cu) recovery from wastewater mitigates environmental pollution and is economically valuable. Mesoporous silica adsorbents, SBA-15, with amine-grafting (SBA-15-NH2) and manganese loading along with amine-grafting (Mn-SBA-15-NH2) were fabricated using KMnO4 and 3-aminopropyltriethoxysilane. The characteristics of the synthesized adsorbents were evaluated in detail in terms of its crystal structure peaks, surface area and pore size distribution, transmission electron microscope and X-ray photoelectron spectroscopy. The results established the 2.08 mmol/g of Cu adsorption capacity on Mn-SBA-15-NH2. Furthermore, in a mixed heavy metal solution, high selective Cu adsorption capacity on Mn-SBA-15-NH2 (2.01 mmol/g) was achieved while maintaining 96% adsorption amount as that of a single Cu solution. Comparatively, Cu adsorption on SBA-15-NH2 decreased by half due to high competition with other heavy metals. Optimal Cu adsorption occurred at pH 5. This pH condition enabled grafted amine group in Mn-SBA-15-NH2 to form strong chelating bonds with Cu, avoiding protonation of amine group (below pH 5) as well as precipitation (above pH 5). The adsorption equilibrium well fitted to Langmuir and Freundlich isotherm models, while kinetic results were represented by models of linear driving force approximation (LDFA) and pore diffusion model (PDM). High regeneration and reuse capacity of Mn-SBA-15-NH2 were well established by its capacity to maintain 90% adsorption capacity in a multiple adsorption-desorption cycle. Cu was selectively extracted from Mn-SBA-15-NH2 with an acid solution
- …