The Fracture Energy and Some Mechanical Properties of a Polyurethane Elastomer

The energy required to form a unit of new surface in the fracture of a polyurethane elastomer is determined. The rate sensitivity of the material has been reduced by swelling it in toluene. This paper primarily describes the experimental work of measuring the lower limit of the fracture energy. With this value and the creep compliance as a basis, the rate dependence of fracture energy for the unswollen material has been determined. It is thus shown that the dependence of the fracture energy on the rate of crack propagation can be explained by energy dissipation around the tip of the crack. Good agreement between the theoretically and experimentally determined relationships for the rate-sensitive fracture energy is demonstrated

Observation of Damage Growth in Compressively Loaded Laminates

An experimental program to determine tie phenomenological aspects of composite-panel failure under simultaneous compressive n-plane loading and low-velocity transverse impact [C-75 m/s (0-250 ft/s)] is described. High-speed photography coupled with the shadow-moiré technique is used to record the phenomenon of failure propagation. The information gained from these records, supplemented by plate sectioning and observation for interior damage, has provided information regarding the failure-propagation mechanism. The results show that the failure process can be divided roughly into two phases. In the first phase the plane is impacted, and the resulting response causes interlaminar separation. In the second phase the local damage spreads to the undamaged portion of the plate through a combination of laminae buckling and further delamination

The compressive failure of graphite/epoxy plates with circular holes

The behavior of fiber reinforced composite plates containing a circular cutout was characterized in terms of geometry (thickness, width, hole diameter), and material properties (bending/extensional stiffness). Results were incorporated in a data base for use by designers in determining the ultimate strength of such a structure. Two thicknesses, 24 plies and 48 plies were chosen to differentiate between buckling and strength failures due to the presence of a cutout. Consistent post-buckling strength was exhibited by both laminate configurations

Crack propagation in a linearly viscoelastic strip

The tip velocity of a crack propagating through a viscoelastic material depends on geometry, applied load and its history, and material properties. A consideration of the work done by the unloading tractions at the crack tip shows that, for a large crack propagating through an infinitely long strip under constant lateral strain, the rate of propagation can be calculated from a knowledge of the intrinsic fracture energy (a material constant), the material creep compliance, and an additional size parameter. This parameter vanishes from the analysis if the material is elastic, and the familiar instability criterion is obtained in this case. Comparison with experimental data is provided and the consequences of step loadings are examined

Crack propagation under variable load histories in linearly viscoelastic solids

Crack propagation under variable loads in linearly viscoelastic solid

On the hygrothermomechanical characterization of polyvinyl acetate

As a part of a program to understand the mechanisms of failure in time-dependent adhesion and film bonding, the creep compliance of polyvinyl acetate (PVAc) in shear has been determined both as a function of temperature and absorbed moisture. Volumetric expansion as a function of temperature or moisture takeup was also measured. We find that practically realizable changes in moisture content affect both the creep compliance and the swelling of PVAc to a degree comparable to that resulting from realistic changes in temperature. For example, the creep rates (histories) at corresponding times for PVAc subjected to 92% relative humidity storage are accelerated by approximately four orders of magnitude over those found for the dry material. Moreover, we find within reasonable experimental error that water concentration affects the time scale of creep like temperature through a concentration-dependent shift factor. An attempt is made at discussing the interrelation of temperature- and moisture-induced volume changes

Planning Activity Report for NDE of Adhesive Bonded Structures

Following a workshop held at the Rockwell International Science Center, Thousand Oaks, California in January, 1979, an ad hoc planning activity was undertaken to set forth a program plan to address the needs in NDE for adhesive bonded structures. The objectives of the planning activity were to develop a program rationale and strategy, determine the existence of reasonable approaches, and to propose a detailed plan of action for review at the annual DARPA/AF meeting in September, 1979. The plan encompasses the basic elements of an accept/reject methodology based on fracture mechanics, expected developments of valid flaw growth models, stress analysis, and non-destructive measurement techniques. A central issue is the prospect for determining a valid non-destructive measure of strength for the bonded joint as might be reflected in the tendency for preexistent flaws to propagate under environmental loads

Visualization of impact damage of composite plates by means of the Moire technique

The phenomenological aspects of propagation damage due to low velocity impact on heavily loaded graphite-epoxy composite laminates were investigated using high speed photography coupled with the moire fringe technique. High speed moire motion records of the impacted specimens are presented. The results provide information on the time scale and sequence of the failure process. While the generation of the initial damage cannot always be separated temporally from the spreading of the damage, the latter takes place on the average with a speed on the order of 200 m/sec

Enhancing Context Specifications for Dependable Adaptive Systems: A Data Mining Approach

Context: Adaptive systems are expected to cater for various operational contexts by having multiple strategies in achieving their objectives and the logic for matching strategies to an actual context. The prediction of relevant contexts at design time is paramount for dependability. With the current trend on using data mining to support the requirements engineering process, this task of understanding context for adaptive system at design time can benefit from such techniques as well. Objective: The objective is to provide a method to refine the specification of contextual variables and their relation to strategies for dependability. This refinement shall detect dependencies between such variables, priorities in monitoring them, and decide on their relevance in choosing the right strategy in a decision tree. Method: Our requirements-driven approach adopts the contextual goal modelling structure in addition to the operationalization values of sensed information to map contexts to the system’s behaviour. We propose a design time analysis process using a subset of data mining algorithms to extract a list of relevant contexts and their related variables, tasks, and/or goals. Results: We experimentally evaluated our proposal on a Body Sensor Network system (BSN), simulating 12 resources that could lead to a variability space of 4096 possible context conditions. Our approach was able to elicit subtle contexts that would significantly affect the service provided to assisted patients and relations between contexts, assisting the decision on their need, and priority in monitoring. Conclusion: The use of some data mining techniques can mitigate the lack of precise definition of contexts and their relation to system strategies for dependability. Our method is practical and supportive to traditional requirements specification methods, which typically require intense human intervention

Damage progression in compressively loaded laminates containing a circular cutout

Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/76038/1/AIAA-10597-113.pd