2 research outputs found
A Study on the Effect of Bond Stress and Process Temperature on Palladium Coated Silver Wire Bonds on Aluminum Metallization
In the past ten years, the increasing price of gold has motivated the wire bonding industry to look for alternative bonding wire materials in the field of microelectronics packaging. A new candidate wire to replace gold is palladium coated silver wire. In this thesis, the effect of the two specific process parameters ābond stressā and āprocess temperatureā on the ball bonds made with the new candidate wire are investigated. Using 20 Ī¼m diameter wire and various level-combinations of these process parameter, ball bonds are produced according to a special accelerated optimization method to result in a target diameter of 46 Ā± 0.5 Ī¼m and target height of 16 Ā± 0.5 Ī¼m. Three different levels are used for each of the specific process parameters. After pre-selecting a few process parameters, the accelerated method determines the levels for the process parameters āimpact forceā and āelectric flame-off currentā with a 2Ć2 design of experiments. Then, the ultrasound parameter is maximized up to a level where a pre-selected ultrasonic deformation occurs to the bonds, maintaining the target bond diameter and height. The bond quality is measured by measuring the shear strength of the bonds. The results show that
ā¢ the bond geometry is not affected by the bond stress,
ā¢ the optimized specific process parameters vary by less than ~0.5 % when bond stress values are varied from 60 to 100 MPa,
ā¢ the variations in optimized parameters are larger than ~3.0 % when the BT is changed from 100 to 200 ĀŗC,
ā¢ ball bonds achieve acceptable shear strength (> 120 MPa) when the values for both, bond stress and bond temperature, are high,
ā¢ ultrasound level and shear stress interact, the higher shear stress the lower the ultrasound level required.
An average shear strength of ~120 MPa is achieved with 11.4 % ultrasound, 100 MPa bond stress, and 200 ĀŗC bond process temperature. In summary, a robust methodology is presented in this thesis to efficiently optimize the ball bonding process as demonstrated with the new candidate wire has a bondability similar to that of gold wire with only minor adjustment in the bonding process needed
Thermal Aging Behavior of Fine Pitch Palladium Coated Silver (PCS) Ball Bonds on Al Metallization
The high price of Au has motivated many to look for alternative bonding wire materials in the field of microelectronics packaging. In the present study, the reliability performance of palladium coated silver (PCS) wire in high temperature storage test (HTST) is carried out using 18 Ī¼m diameter fine pitch PCS wire. Fine pitch ball bonds are made on Al metallization, with bonded ball diameter (BBD) of 32 Ā± 0.5 Ī¼m and ball height (BH) of 8 Ā± 0.5 Ī¼m. The aging temperature used in HTST is 170 Ā°C and both shear and pull test are used to evaluate the aged ball bonds at regular time intervals. The shear force increases from 9.9 gf at 96 h to 12.5 gf at 192 h, and remains almost constant until 1344 h, and starts dropping gradually until 10.9 gf at 1848 h. The pad lift percentage recorded in pull test gradually drops from 90 % at 96 h to 20 % at 1008 h, and increases to 90 % at 1848 h. The chip side fractography after shear test indicates that the main failure modes are through pad at 96 h, through ball bond at 504 h, and half of both at 168 h, respectively. Cross-sectional images show that the thickness of the intermetallic compound (IMC) layer growth follows parabolic relationship and the rate constant is 0.10 Ā± 0.02 Ī¼m/hĀ½. Gaps are observed along the periphery of the ball bond interface where no IMC is observed. The IMCs are located at the center of the ball bond interface, and the width is 16.0ā19.3 Ī¼m at 96 h and 17.2ā22.7 Ī¼m at 1344 h, respectively