Severity parameter and global importance factor of non-newtonian models in 3D reconstructed human left coronary artery

This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, Aristotle University of Thessaloniki, University of Thessaly, IPEM, the Process Intensification Network, the Institution of Mechanical Engineers, the Heat Transfer Society, HEXAG - the Heat Exchange Action Group, and the Energy Institute.The capabilities and limitations of various molecular viscosity models, when testing Left Coronary Artery (LCA) tree, were analyzed via: molecular viscosity, local and global non-Newtonian importance factors, Wall Shear Stress (WSS) and Wall Shear Stress Gradient (WSSG). Seven non-Newtonian molecular viscosity models, plus the Newtonian one, were compared. Dense grid of 620000 nodes located, mostly, at near to low WSS flow regions (endothelium regions) is needed for current LCA application. The WSS distribution yields a consistent LCA pattern for nearly all non-Newtonian models. High molecular viscosity, low WSS low WSSG values appear at proximal LCA regions at the outer walls of the major bifurcation. The global importance factor for the non-Newtonian power law model yields 76.7% (non-Newtonian flow), while for the Generalized power law model this value is 6.1% (Newtonian flow). The capabilities of the applied non-Newtonian law models appear at low strain rates. The Newtonian blood flow treatment is considered to be a good approximation at mid-and high-strain rates. In general, the non-Newtonian power law and the Generalized power law blood viscosity models are considered to approximate the molecular viscosity and WSS calculations in a more satisfactory way

Oscillating shear index, wall shear stress and low density lipoprotein accumulation in human RCAs

This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, Aristotle University of Thessaloniki, University of Thessaly, IPEM, the Process Intensification Network, the Institution of Mechanical Engineers, the Heat Transfer Society, HEXAG - the Heat Exchange Action Group, and the Energy Institute.Atherosclerosis shows predilection in regions of coronary arteries with hemodynamic particularities as, local disturbances of Wall Shear Stress (WSS) in space and time, and locally high concentrations of lipoprotein. Six, image-based human deceased, Right Coronary Arteries (RCA) are used to elucidate, a) Low Density Lipoprotein (LDL) transport under steady flow and b) oscillating flow (no mass transfer). A semi-permeable nature of the arterial wall computational model is incorporated with hydraulic conductivity and permeability treated as WSS dependent. The 3D reconstruction technique is a combination of angiography and IVUS. LDL is elevated at locations where WSS is low. Under steady flow conditions the area-averaged normalized LDL concentration over the RCAs, using shear dependent water infiltration and endothelial permeability is 9.6 % higher than at entrance. However, under constant water infiltration and endothelial permeability this value is only 3.2 %. High Oscillating Shear Index (OSI) and low average WSS nearly co-locate. Approximately 630000 grid nodes proved to be sufficient enough to accurately describe the oscillating flow and the LDL concentration within the RCAs

Wall shear stress and low density lipoprotein concentration in stented arteries

This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, Aristotle University of Thessaloniki, University of Thessaly, IPEM, the Process Intensification Network, the Institution of Mechanical Engineers, the Heat Transfer Society, HEXAG - the Heat Exchange Action Group, and the Energy Institute.Current computational analysis results quantify Wall Shear Stress (WSS) and its impact on Low Density Lipoprotein (LDL) concentration of a fully deployed straight artery stent. Atherosclerosis shows predilection in arterial regions with hemodynamic particularities, as local disturbances of WSS in space, and locally high concentrations of lipoprotein. The WSS and subsequently the LDL distribution are important indicators of stent performance. A typical 6.0 mm diameter straight stented artery is used to elucidate the WSS and the LDL transport under steady flow conditions treating the blood as a non-Newtonian fluid. Struts are 50.0 % embedded into the arterial wall. Emphasis is placed in the LDL distribution at the upstream and downstream flow regions of each strut intersection. Reduced WSS values are observed towards outlet. At the strut intersections, high WSS values are observed possibly causing platelet activation. Prone to plaque development are flow regions located at specific strut intersections (mostly at the vicinity of the curved struts) where increased LDL concentration is observed. The maximum LDL concentration over the stented artery reaches a value of 3.8 % higher than that at the entrance. The concentration at distal to any strut region was higher than proximal to the strut

Texture Analysis and Radial Basis Function Approximation for IVUS Image Segmentation

>Intravascular ultrasound (IVUS) has become in the last years an important tool in both clinical and research applications. The detection of lumen and media-adventitia borders in IVUS images represents a first necessary step in the utilization of the IVUS data for the 3D reconstruction of human coronary arteries and the reliable quantitative assessment of the atherosclerotic lesions. To serve this goal, a fully automated technique for the detection of lumen and media-adventitia boundaries has been developed. This comprises two different steps for contour initialization, one for each corresponding contour of interest, based on the results of texture analysis, and a procedure for approximating the initialization results with smooth continuous curves. A multilevel Discrete Wavelet Frames decomposition is used for texture analysis, whereas Radial Basis Function approximation is employed for producing smooth contours. The proposed method shows promising results compared to a previous approach for texture-based IVUS image analysis

Influence of Oscillating Flow on LDL Transport and Wall Shear Stress in the Normal Aortic Arch

Lipid accumulation in the aortic wall is an important factor in the development of atherosclerosis. The Low Density Lipoprotein (LDL) at the surface of the endothelium in relation to Wall Shear Stress (WSS) in the normal human aortic arch under unsteady, normal flow and mass conditions was computationally analysed. Concave sides of the aortic arch exhibit, relatively to the convex ones, elevated LDL levels at the surface of the endothelium for all time steps. At the peak systolic velocity, the LDL level reaches a value 23.0% higher than that at entrance in the ascending-descending aorta region. The corresponding LDL levels at the surface of the endothelium for the near minimum entrance velocity instant reaches 26.0%. During the cardiac cycle, the highest area averaged normalized LDL taken up as compared to the lowest one is 0.69%. WSS plays an important role in the lipid accumulation. Low WSS regions are exposed to high LDL levels at the surface of the endothelium. Regions of elevated LDL levels do not necessarily co-locate to the sites of lowest WSS. The near wall paths of the velocities might be the most important factor for the elevated LDL levels at the surface of the endothelium

Three-dimensional reconstruction of coronary arteries and plaque morphology using CT angiography – comparison and registration with IVUS

BACKGROUND: The aim of this study is to present a new methodology for three-dimensional (3D) reconstruction of coronary arteries and plaque morphology using Computed Tomography Angiography (CTA). METHODS: The methodology is summarized in six stages: 1) pre-processing of the initial raw images, 2) rough estimation of the lumen and outer vessel wall borders and approximation of the vessel’s centerline, 3) manual adaptation of plaque parameters, 4) accurate extraction of the luminal centerline, 5) detection of the lumen - outer vessel wall borders and calcium plaque region, and 6) finally 3D surface construction. RESULTS: The methodology was compared to the estimations of a recently presented Intravascular Ultrasound (IVUS) plaque characterization method. The correlation coefficients for calcium volume, surface area, length and angle vessel were 0.79, 0.86, 0.95 and 0.88, respectively. Additionally, when comparing the inner and outer vessel wall volumes of the reconstructed arteries produced by IVUS and CTA the observed correlation was 0.87 and 0.83, respectively. CONCLUSIONS: The results indicated that the proposed methodology is fast and accurate and thus it is likely in the future to have applications in research and clinical arena