CONVERSION OF DIESEL ENGINE INTO SPARK IGNITION ENGINE TO WORK WITH CNG AND LPG FUELS FOR MEETING NEW EMISSION NORMS

Fluctuating fuel prices and associated pollution problems of largely exploited petroleum liquid fuel has stimulated the research on abundantly available gaseous fuels to keep the mobility industry intact. In the present work an air cooled diesel engine was modified suitably into a spark ignition engine incorporating electronic ignition and variable speed dependant spark timing to accommodate both LPG and CNG as fuels. Engine was optimized for stoichiometric operation on engine dynamometer. Materials of a few intricate engine components were replaced to suit LPG and CNG application. Ignition timing was mapped to work with gaseous fuels for different speeds. Compensation was done for recovering volumetric efficiency when operated with CNG by introducing more volume of air through resonator. Ignition timing was observed to be the pertinent parameter in achieving good performance with gaseous fuels under consideration. Performance and emission tests were carried out on engine dynamometer and chassis dynamometer. Under wide open throttle and at rated speed condition, it was observed that the peak pressure with LPG was lying between diesel fuel and CNG fuel operation due to slow burning nature of gaseous fuels. As compression ratio was maintained same for LPG and CNG fuel operation, low CO emissions were observed with LPG where as HC + NOx emissions were lower with CNG fuel operation. Chassis dynamometer based emission tests yielded lower CO2 levels with CNG operation

Investigations of effects of pilot injection with change in level of compression ratio in a common rail diesel engine

These day diesel engines are gaining lots of attention as prime movers for various source of transportation. It offers better drive ability, very good low end torque and importantly the lower CO2 emission. Diesel engines are bridging the gap between gasoline and diesel engines. Better noise vibration and harshness levels of gasoline engine are realized to great extent in diesel engine, thanks to common rail direct injection system. Common rail injection system is now well known entity. Its unique advantage is flexible in operation. In common rail injection system, number of injection prior and after main injection at different injection pressure is possible. Due to multiple injections, gain in emission reduction as well as noise has been already experienced and demonstrated by researcher in the past. However, stringent emission norms for diesel engine equipped vehicle demands for further lower emission of oxides of nitrogen (NOx) and particulate matter (PM). In the present paper, authors attempted to study the effect of multiple injections in combination with two level of compression ratio. The aim was to study the combustion behavior with the reduced compression ratio which is going to be tried out as low temperature combustion concept in near future. The results were compared with the current level of compression ratio. Experiments were carried out in 2.2L cubic capacity engine with two levels of compression ratios. Pilot injection separation and quantities were varied keeping the main injection, rail pressure, boost pressure and EGR rate constant. Cylinder pressure traces and gross heat release rates were measured and analyzed to understand the combustion behavior

Effective utilization of B20 blend with diethyl ether and ethanol as oxygenated additives

In the recent times' fatty acid methyl ester popularly called as biodiesel has become more prominent alternate fuel for compression ignition engines based on a single fuel concept. Since, use of neat biodiesel on a large scale is raising certain difficulties and is being adopted in a blended form with petro-diesel fuel and B20 blend has become standardized. However, the HC and NOx emissions of B20 are still on the higher side. Present work aims at experimental evaluation of a single cylinder water-cooled diesel engine by adopting various proportions of ethanol and diethyl ether blends in order to improve performance and emission characteristics of B20 blend. Besides employing different amounts of ethanol and diethyl ether, simultaneous influence of injector nozzle hole size and fuel injection pressure are also investigated to arrive at an optimum configuration. Brake specific fuel consumption and hydrocarbon emissions values are lower with B20 and DEE 5 whereas B20 with DEE15 yielded lower NOx emissions. It is observed that addition of oxygenates have improved the combustion process and lower emissions are obtained. The present investigation revealed that blends with oxygenated additives having higher Cetane rating are superior to neat blend

Internal and External Influences on Hydro-Thermal Behavior of Micro-channel Flow

Microchannel flow is an effective solution for many engineering problems. Application of microchannels is found in various fields such as thermal management of electronics, micro-combustors, biomedical industries, MEMS. In microchannel flow, some internal and external influences such as surface roughness, electric and magnetic fields are very significant and commonly neglected in macro-scale flow. Early research works on microchannels stated that the conventional theories of macro-scale flow were not applicable for microscale flows. Finally, researchers are concluded that the deviation in conventional theories in the case of micro-scale flow is because of neglecting the internal forces, surface roughness, surface wettability, etc., which play a prime role in micro-scale flows. In this chapter, the behavior of microchannel flow under the internal and external influences is discussed. The heat transfer and hydrodynamic characteristics of microchannel flow under the external magnetic field and electric fields are presented. The effect of surface morphology, roughness, electro-osmotic effect, electrophoresis, internal heat generation, and analysis methods is discussed