Previous Damage Accumulation Can Influence Femoral Fracture Strength: A Finite Element Study

To manage osteoporotic hip fracture risk, it is necessary to understand failure mechanisms of bone at both the material and organ level. The structural response of bone is dependent on load history. Repeated loading causes progressive microstructural cracking, resulting in reduced apparent-level stiffness and, if damage is significant, reductions to peak load bearing capability. However, the effect of previous damage accumulation has not been well explored at the organ level. It was hypothesized that femoral fracture load and fracture pattern may be sensitive to damage accumulation from previous loading events. Six cadaveric specimens were used to develop patient specific finite element (FE) models from quantitative tomographic (qCT) scans. Material properties were assigned from qCT intensity at each element location, and damage evolution was predicted using a previously validated quasi-brittle FE model. Three scenarios were investigated: stumble followed by another stumble (S-S), fall followed by another fall (F-F), and stumble followed by a fall (S-F). Fracture load and pattern were compared to FE predictions for a single stumble (S) or single fall (F) loading event. Most specimens were resilient to accumulated damage, showing little (<5%) change in fracture load from the multiple-load scenarios (S-S, F-F, and S-F) compared to an equivalent single load scenario (S or F). Only one specimen demonstrated moderate (5-15%) reductions in strength from all three multiple-load scenarios. However, two specimens experienced moderate (20-30%) increase in fracture load in some load cases. In these cases, initial damage caused the load to be more evenly distributed upon subsequent loading events

The acetabular labrum: A review of its function

The acetabular labrum is a soft-tissue structure which lines the acetabular rim of the hip joint. Its role in hip joint biomechanics and joint health has been of particular interest over the past decade. In normal hip joint biomechanics, the labrum is crucial in retaining a layer of pressurised intra-articular fluid for joint lubrication and load support/distribution. Its seal around the femoral head is further regarded as a contributing to hip stability through its suction effect. The labrum itself is also important in increasing contact area thereby reducing contact stress. Given the labrum's role in normal hip joint biomechanics, surgical techniques for managing labral damage are continuously evolving as our understanding of its anatomy and function continue to progress. The current paper aims to review the anatomy and biomechanical function of the labrum and how they are affected by differing surgical techniques

Femoral fracture load and fracture pattern is accurately predicted using a gradient-enhanced quasi-brittle finite element model

Nonlinear finite element (FE) modeling can be a powerful tool for studying femoral fracture. However, there remains little consensus in the literature regarding the choice of material model and failure criterion. Quasi-brittle models recently have been used with some success, but spurious mesh sensitivity remains a concern. The purpose of this study was to implement and validate a new model using a custom finite element designed to mitigate mesh sensitivity problems. Six specimen-specific FE models of the proximal femur were generated from quantitative tomographic (qCT) scans of cadaveric specimens. Material properties were assigned a-priori based on average qCT intensities at element locations. Specimens were experimentally tested to failure in a stumbling load configuration, and the results were compared to FE model predictions. There was a strong linear relationship between FE predicted and experimentally measured fracture load (R2= 0.79), and error was less than 14% over all cases. In all six specimens, surface damage was observed at sites predicted by the FE model. Comparison of qCT scans before and after experimental failure showed damage to underlying trabecular bone, also consistent with FE predictions. In summary, the model accurately predicted fracture load and pattern, and may be a powerful tool in future studies

Mechanisms of stem subsidence in femoral impaction allografting

Failure of the femoral component of total hip arthroplasty is often accompanied by bone loss that can pose a significant challenge to the orthopaedic surgeon. Femoral impaction allografting has attractive potential for restoring bone stock in deficient femurs. However, there have been reports of problematic postoperative stem subsidence with this procedure. Subsidence is highly variable among patients, and there is disagreement over the mechanisms that cause it. This article reviews the various mechanisms that can contribute to subsidence in femoral impaction allografting. Variables such as graft density, cement penetration profile, use of synthetic graft substitutes, or other graft additives are discussed, as well as their potential impact on subsidence. Finally, recommendations are made for future studies aiming to reduce the risk of excessive subsidence in femoral impaction allografting

Properties of the cartilage layer from the cam-type hip impingement deformity

Femoro-acetabular impingement (FAI) is associated with significant acetabular cartilage damage and degenerative arthritis. To understand the contact stress and thus biomechanical mechanisms that may contribute to degeneration, the material behaviour of the cartilage layer is required. The objective of this study is to determine the fibril-reinforced poroelastic properties and composition of cartilage from cam deformities and to compare to those of normal cartilage. Patients undergoing surgical treatment of a symptomatic cam FAI deformity were recruited from the clinical practice of one of the authors. Osteochondral specimens were retrieved from the deformity during surgery using a trephine. Control specimens were retrieved from the anterior femoral head bearing surface during autopsy procedures. Indentation stress-relaxation tests were performed to determine the modulus (ES), Poisson's ratio (ν) and permeability (k0) of the poroelastic component, and the strain-independent (E0) and -dependent (Eε) moduli of the fibril-reinforcement using finite element analysis and optimization. Safranin-O staining was used to quantify proteoglycan content. ES and ν were 71% and 37% lower, respectively, in Cam specimens compared to controls, and k0 was approximately triple that of Control specimens (p <. 0.05). No significant differences were seen in the fibrillar components, E0 and Eε. Proteoglycan content was substantially depleted in Cam specimens, and was correlated with ES, ν and k0. This study showed that cartilage from the cam deformity exhibits severe degeneration in terms of the mechanical behaviour and composition changes, and is consisten

Influence of ingrowth regions on bone remodelling around a cementless hip resurfacing femoral implant

Hip resurfacing arthroplasty is an alternative to traditional hip replacement that can conserve proximal bone stock and has gained popularity but bone resorption may limit implant survival and remains a clinical concern. The goal of this study was to analyze bone remodelling patterns around an uncemented resurfacing implant and the influence of ingrowth regions on resorption. A computed tomography-derived finite element model of a proximal femur with a virtually implanted resurfacing component was simulated under peak walking loads. Bone ingrowth was simulated by six interface conditions: fully bonded; fully friction; bonded cap with friction stem; a small bonded region at the stem-cup intersection with the remaining surface friction; fully frictional, except for a bonded band along the distal end of the cap and superior half of the cap bonded with the rest frictional. Interface condition had a large influence on remodelling patterns. Bone resorption was minimized when no ingrowth occurred at the bone-implant interface. Bonding only the superior half

Validation of an alignment method using motion tracking system for in-vitro orientation of cadaveric hip joints with reduced set of anatomical landmarks

Accurate in-vitro orientation of cadaveric hip joints is challenging due to limited available anatomical landmarks. Published hip joint in-vitro investigations commonly lack details on methods used to achieve reported orientations and the accuracy with which the desired orientation has been achieved. The aim of this study was to develop an accurate method for orienting hip joints with limited anatomical landmarks for in-vitro investigations, and to compare this method against orientation using guiding axes and by visual approximation. The proposed orientation method resulted in orientation angles achieved to within one degree (SD ± 0.58°). For most specimens, orientation using physical tools resulted in errors of ±8° and ±12° in at least one of three orientation angles used to place the femur and pelvis in neutral orientation, respectively. Precision was also worse, with SDs ranging from ±1° to ±5° for orientation angles of femoral specimens and SDs ranging from ±1° to ±8° for pelvic specimens. The error in the orientation angles was worse for orientation by visual approximation and the range of SDs were greater for both the femur and pelvis

Surgical Correction of Cam Deformity in Association with Femoroacetabular Impingement and Its Impact on the Degenerative Process within the Hip Joint

Background: Cam morphology in association with femoroacetabular impingement (FAI) is a recognized cause of hip pain and cartilage damage and proposed as a leading cause of arthritis. The purpose of this study was to analyze the functional an

Bone density is higher in cam-type femoroacetabular impingement deformities compared to normal subchondral bone

Objective: Cam-type femoroacetabular impingement (FAI) deformities have been associated with early osteoarthritic degeneration of the hip. Degeneration depends on many factors such as joint morphology and dynamics of motion. Bone mineral density (BMD) appears to be a manifestation of the above, and may be a potentiator. Thus the goal of this study was to assess subchondral BMD of cam deformities in symptomatic and asymptomatic FAI subjects, and to compare to normal controls. M