Actinides, accelerators and erosion

Fallout isotopes can be used as artificial tracers of soil erosion and sediment accumulation. The most commonly used isotope to date has been 137Cs. Concentrations of 137Cs are, however, significantly lower in the Southern Hemisphere, and furthermore hav

Yangtse River sediments and erosion rates from source to sink traced with cosmogenic 10 Be: Sediments from major rivers

Estimates of regional erosion and sediment mixing from different sources in the Yangtse River system are presented, based on sand samples collected from major tributaries and the trunk stream, at 23 sites between western Sichuan and the Yangtse Delta. Mixing is estimated from concentrations of Mg, Ca, Sr, Ti, Mn and Fe, which are substantially higher in sand from major tributaries in the western Yangtse River catchment than from tributaries in the eastern catchment. Intermediate concentrations occur in sand from the Yangtse Delta, both for modern samples from the surface and for early Holocene samples from drill holes. Mixing ratios indicate that 35 ± 5% of sand in the delta came from eastern sources. A similar result was obtained using cosmogenic 10Be in quartz grains as a tracer of mixing. Regional erosion rate estimated from 10Be in sand grains from high mountain catchments of the western Yangtse River are mostly similar to rates based on sediment gauging but are sometimes higher, and range to over 700 m Ma- 1, while 10Be measured at upper Yangtse River tributaries on the northeast Tibetan plateau gave rates of 20-30 m Ma- 1. For the eastern catchments, 10Be measurements from quartz sand and sediment gauging both gave rates of 30-70 m Ma- 1. Eroding at this rate, the eastern catchments could not supply more than 20% of the sediment in the delta, in contrast with 35% estimated from geochemical fingerprints. The relative input from eastern sources may have been higher in Late Pleistocene times, under a different climatic regime, and reworking of Pleistocene deposits may still be in progress

Uranium comparison by means of AMS and ICP-MS and Pu and 137Cs results around an Italian nuclear power plant

Italy built and commissioned 4 nuclear power plants between 1958-1978, which delivered a total of 1500 MW. All four were closed down after the Chernobyl accident following a referendum in 1987. One of the plants was Garigliano, commissioned in 1959. This plant used a 160 MW BWR1 (SEU of 2.3 %) and was operational from 1964 to 1979, when it was switched off for maintenance. It was definitively stopped in 1982, and is presently being decommissioned. We report here details on the chemistry procedure and on the measurements for soil samples, collected up to 4.5 km from the Nuclear Plant. A comparison between uranium (238U) concentration as determined by means of AMS (Accelerator Mass Spectrometry) and by ICP-MS (Inductively Coupled Plasma-Mass Spectrometry) techniques respectively at the ANU (Australian National University) and at the Ecowise company in Canberra, Australia, is reported, as well as 236U and 239;240Pu concentration results detected by AMS. 236U/238U and 240Pu/239Pu isotopic ratios by means of AMS are also provided. A contamination from Chernobyl is visible in the 137Cs/239+240Pu activity ratio measurements

Robust radiocarbon dating of wood samples by high-sensitivity liquid scintillation spectroscopy in the 50–70 kyr age range

Although high-sensitivity liquid scintillation (LS) spectroscopy is theoretically capable of producing finite radiocarbon ages in the 50,000- to 70,000-yr range, there is little evidence in the literature that meaningful dates in this time period have been obtained. The pressing need to undertake calibration beyond 26 kyr has resulted in the regular publication of ¹⁴C results in excess of 50 kyr, yet very little effort has been made to demonstrate their accuracy or precision. There is a paucity of systematic studies of the techniques required to produce reliable dates close to background and the methods needed to assess contamination from either in situ sources or laboratory handling and processing. We have studied the requirements for producing accurate and reliable dates beyond 50 kyr. Laboratory procedures include optimization of LS spectrometers to obtain low and stable non-¹⁴C background count rates, use of low-background counting vials, large benzene volumes, long counting times, and preconditioning of vacuum lines. We also discuss the need for multiple analyses of a suitable material containing no original ¹⁴C (background blank) and the application of an appropriate statistical model to compensate for variability in background contamination beyond counting statistics. Accurate and reproducible finite ages >60 kyr are indeed possible by high-sensitivity LS spectroscopy, but require corroborating background blank data to be defensible

Amplified erosion above waterfalls and oversteepened bedrock reaches

None of the conventional bedrock erosion laws can predict incision immediately upslope of a waterfall lip where the flow is accelerating toward a freefall. Considering the expected increase in flow velocity and shear stress at the lip of a waterfall, we determine erosion amplification at a waterfall lip as [equation], where [equation] is the erosion rate at the upstream end of the flow acceleration zone above a waterfall, Fr is the Froude number at this setting, and n ranges between 0.5–1.7. This amplification expression suggests that erosion at the lip could be as much as 2–5 times higher relative to erosion at a normal setting with identical hydraulic geometry. Utilizing this erosion amplification expression in numerical simulations, we demonstrate its impact on reach-scale morphology above waterfalls. Amplified erosion at the lip of a waterfall can trigger the formation of an oversteepened reach whose length is longer than the flow acceleration zone, provided incision wave velocity (Vi) at the upstream edge of the flow acceleration zone is higher than the retreat velocity of the waterfall face. Such an oversteepened reach is expected to be more pronounced when Vi increases with increasing slope. The simulations also suggest that oversteepening can eventually lead to steady state gradients adjacent to a waterfall lip provided Vi decreases with increasing slope. Flow acceleration above waterfalls can thus account, at least partially, for prevalent oversteepened bedrock reaches above waterfalls. Using the cosmogenic isotope Cl-36, we demonstrate that incision wave velocity upstream of a waterfall at the Dead Sea western escarpment is probably high enough for freefall-induced oversteepening to be feasible

Potential of lichens for monitoring iodine-129 and chlorine-36

Chlorine-36 (half life 3.01 × 105 year), a beta emitter, is produced naturally but its presence has been enhanced by atmospheric weapons testing and other nuclear activities. Iodine-129 has a half life of 1.57 × 107 years and is also produced by nuclea

Improving the detection limit for 182 Hf

A nearby supernova would deposit radionuclides on earth. The long-lived radionuclide 182Hf (t1/2 = 8.9 Ma) is one of a number of candidates for an isotopic signature of such an event. Together with 60Fe, observation of 182Hf would be direct evidence for a supernova site of the r-process. The most suitable site for searching for such a signature would be a deep-sea sediment of slow deposition rate. Measurement of 182Hf at the anticipated level requires very effective suppression of the interfering stable isobar 182W. Chemical separation and the injection of HfF5- allow for suppression by several orders of magnitude, but more is needed for detection of 182Hf as a supernova isotope signature. We are currently developing AMS methods for measuring 182Hf/180Hf isotope ratios at the required level using a 15 MV tandem accelerator . Both projectile X-ray emission and the use of a solid passive absorber with a subsequent measurement of the residual energy are being explored. The former suffers from low efficiency, but the latter looks promising

Production of 21 Ne in depth-profiled olivine from a 54 Ma basalt sequence, Eastern Highlands (37° S), Australia

In this study we investigate the cosmogenic neon component in olivine samples from a vertical profile in order to quantify muogenic 21Ne production in this mineral. Samples were collected from an 11 m thick Eocene basalt profile in the Eastern Highlands of southeastern Australia. An eruption age of 54.15 ± 0.36 Ma (2σ) was determined from 40Ar/39Ar step-heating experiments (n = 6) on three whole-rock samples. A 36Cl profile on the section indicated an apparent steady state erosion rate of 4.7 ± 0.5 m Ma−1. The eruption age was used to calculate in situ produced radiogenic 4He and nucleogenic 3He and 21Ne concentrations in olivine. Olivine mineral separates (n = 4), extracted from the upper two metres of the studied profile, reveal cosmogenic 21Ne concentrations that attenuate exponentially with depth. However, olivine (Fo68) extracted from below 2 m does not contain discernible 21Ne aside from magmatic and nucleogenic components, with the exception of one sample that apparently contained equal proportions of nucleogenic and muogenic neon. Modelling results suggest a muogenic neon sea-level high-latitude production rate of 0.02 ± 0.04 to 0.9 ± 1.3 atoms g−1 a−1 (1σ), or <2.5% of spallogenic cosmogenic 21Ne production at Earth’s surface. These data support a key implicit assumption in the literature that accumulation of muogenic 21Ne in olivine in surface samples is likely to be negligible/minimal compared to spallogenic 21Ne

A study of soil formation rates using 10Be in the wet-dry tropics of northern Australia

A catchment level study to obtain soil formation rates using beryllium-10 (10Be) tracers has been undertaken in the Daly River Basin in the wet-dry tropics of northern Australia. Three soil cores have been collected to bedrock, with depths ranging from

A novel beam focus control at the entrance to the ANU 14UD accelerator

Tandem electrostatic accelerators often require the flexibility to operate at variety of terminal voltages to cater for various user needs. However beam transmission will only be optimal for a limited range of terminal voltages. This paper describes a fo