MHz Unidirectional Rotation of Molecular Rotary Motors

A combination of cryogenic UV-vis and CD spectroscopy and transient absorption spectroscopy at ambient temperature is used to study a new class of unidirectional rotary molecular motors. Stabilization of unstable intermediates is achieved below 95 K in propane solution for the structure with the fastest rotation rate, and below this temperature measurements on the rate limiting step in the rotation cycle can be performed to obtain activation parameters. The results are compared to measurements at ambient temperature using transient absorption spectroscopy, which show that behavior of these motors is similar over the full temperature range investigated, thereby allowing a maximum rotation rate of 3 MHz at room temperature under suitable irradiation conditions

Combinatorial Selection Among Geometrical Isomers of Discrete Long-Carbon-Chain Naphthalenediimides Induces Local Order at the Liquid/Solid Interface

We report two families of naphthalenediimides (NDIs) symmetrically functionalized with discrete carbon chains comprising up to 55 carbon atoms (Cn-NDI-Cn, n = 39, 44, 50, and 55) and their self-assembly at the 1-phenyloctane/highly oriented pyrolytic graphite interface (1-PO/HOPG interface). The compounds differ by the presence or absence of two or three internal double bonds in the carbon chains (unsaturated and saturated Cn-NDI-Cn, respectively). Combinatorial distributions of geometrical isomers displaying either the E- or Z-configuration at each double bond are obtained for the unsaturated compounds. Analysis of the self-assembled monolayers of equally long unsaturated and saturated Cn-NDI-Cn by scanning tunneling microscopy (STM) reveal that all Cn-NDI-Cn tend to form lamellar systems featuring alternating areas of aromatic cores and carbon chains. Extended chain lengths are found to significantly increase disorder in the self-assembled monolayers due to misalignments and enhanced strength of interchain interactions. This phenomenon is antagonized by the local order-inducing effect of the internal double bonds: unsaturated Cn-NDI-Cn give qualitatively more ordered self-assembled monolayers compared to their saturated counterparts. The use of combinatorial distributions of unsaturated Cn-NDI-Cn geometrical isomers does not represent a limitation to achieve local order in the self-assembled monolayers. The self-assembly process operates a combinatorial search and selects the geometrical isomer(s) affording the most thermodynamically stable pattern, highlighting the adaptive character of the system. Finally, the antagonistic interplay between the extended carbon chain lengths and the presence of internal double bonds brings to the discovery of the lamellar "phase C" morphology for unsaturated Cn-NDI-Cn with n ≥ 50

<i>In situ</i> EPR and Raman spectroscopy in the curing of bis-methacrylate-styrene resins

The curing of bis-methacrylate-styrene resins initiated by the cobalt catalyzed decomposition of cumyl hydroperoxide is monitored at ambient temperatures in situ by EPR and Raman spectroscopy. EPR spectroscopy shows the appearance of organic radicals after ca. 1 h from initiation with an increase in intensity from both polystyrene and methacrylate based radical species over a further ca. 2 h period to reach a maximum spin concentration of ca. 2-3 mM. Alkene conversion to polymer was monitored by Raman spectroscopy in real time in situ with EPR spectroscopy and reveals that the appearance of the radical signals is first observed only as the conversion approaches its maximum extent (70% at room temperature), i.e., the resin reaches a glass-like state. The radicals persist for several months on standing at room temperature. Flash frozen samples (77 K) did not show EPR signals within 1 h of initiation. The nature of the radicals responsible for the EPR spectra observed were explored by DFT methods and isotope labelling experiments (D8-styrene) and correspond to radicals of both methacrylate and polystyrene. Combined temperature dependent EPR and Raman spectroscopy shows that conversion increases rapidly upon heating of a cured sample, reaching full conversion at 80 °C with initially little effect on the EPR spectrum. Over time (i.e. subsequent to reaching full conversion of alkene) there was a small but clear increase in the EPR signal due to the methacrylate based radicals and minor decrease in the signal due to the polystyrene based radicals. The appearance of the radical signals as the reaction reaches completion and their absence in samples flash frozen before polymerization has halted, indicate that the observed radicals are non-propagating. The formation of the radicals due to stress within the samples is excluded. Hence, the observed radicals are a representative of the steady state concentration of radicals present in the resin over the entire timespan of the polymerization. The data indicate that the lack of EPR signals is most likely due to experimental aspects, in particular spin saturation, rather than low steady state concentrations of propagating radicals during polymerization.</p

Optimization of Enzymatic Biochemical Logic for Noise Reduction and Scalability: How Many Biocomputing Gates Can Be Interconnected in a Circuit?

We report an experimental evaluation of the "input-output surface" for a biochemical AND gate. The obtained data are modeled within the rate-equation approach, with the aim to map out the gate function and cast it in the language of logic variables appropriate for analysis of Boolean logic for scalability. In order to minimize "analog" noise, we consider a theoretical approach for determining an optimal set for the process parameters to minimize "analog" noise amplification for gate concatenation. We establish that under optimized conditions, presently studied biochemical gates can be concatenated for up to order 10 processing steps. Beyond that, new paradigms for avoiding noise build-up will have to be developed. We offer a general discussion of the ideas and possible future challenges for both experimental and theoretical research for advancing scalable biochemical computing

Molecule-by-Molecule Writing Using a Focused Electron Beam

The resolution of lithography techniques needs to be extended beyond their current limits to continue the trend of miniaturization and enable new applications. But what is the ultimate spatial resolution? It is known that single atoms can be imaged with a highly focused electron beam. Can single atoms also be written with an electron beam? We verify this with focused electron-beam-induced deposition (FEBID), a direct-write technique that has the current record for the smallest feature written by (electron) optical lithography. We show that the deposition of an organometallic precursor on graphene can be followed molecule-by-molecule with FEBID. The results show that mechanisms that are inherent to the process inhibit a further increase in control over the process. Hence, our results present the resolution limit of (electron) optical lithography techniques. The writing of isolated, subnanometer features with nanometer precision can be used, for instance, for the local modification of graphene and for catalysis.</p