6 research outputs found
Twisted Nanotubes of Transition Metal Dichalcogenides with Split Optical Modes for Tunable Radiated Light Resonators
Synthesized micro- and nanotubes composed of transition metal dichalcogenides
(TMDCs) such as MoS are promising for many applications in nanophotonics,
because they combine the abilities to emit strong exciton luminescence and to
act as whispering gallery microcavities even at room temperature. In addition
to tubes in the form of hollow cylinders, there is an insufficiently-studied
class of twisted tubes, the flattened cross section of which rotates along the
tube axis. As shown by theoretical analysis, in such nanotubes the interaction
of electromagnetic waves excited at opposite sides of the cross section can
cause splitting of the whispering gallery modes. By studying
micro-photoluminescence spectra measured along individual MoS tubes, it has
been established that the splitting value, which controls the energies of the
split modes, depends exponentially on the aspect ratio of the cross section,
which varies in "breathing" tubes, while the relative intensity of the modes in
a pair is determined by the angle of rotation of the cross section. These
results open up the possibility of creating multifunctional tubular TMDC
nanodevices that provide resonant amplification of self-emitting light at
adjustable frequencies
Single-Bilayer Graphene Test Structures for Kelvin Probe Microscopy
A new technique for determining the point spread function, which is required for measuring the surface potential using Kelvin probe microscopy (KPM), is presented. The method involves using a silicon carbide substrate coated with single-layer and bilayer graphene as a test structure and obtaining KPM potential profiles in different directions on the surface. This makes it possible to determine the KPM point spread function, which can be used to perform deconvolution and accurately recover the surface potential
Quality Assessment of Processed Graphene Chips for Biosensor Application
The quality of graphene intended for use in biosensors was assessed on manufactured chips using a set of methods including atomic force microscopy (AFM), Raman spectroscopy, and low-frequency noise investigation. It is shown that local areas of residues on the graphene surface, formed as a result of the interaction of graphene with a photoresist at the initial stage of chip development, led to a spread of chip resistance (R) in the range of 1–10 kOhm and to an increase in the root mean square (RMS) roughness up to 10 times, which can significantly worsen the reproducibility of the parameters of graphene chips for biosensor applications. It was observed that the control of the photoresist residues after photolithography (PLG) using AFM and subsequent additional cleaning reduced the spread of R values in chips to 1–1.6 kOhm and obtained an RMS roughness similar to the roughness in the graphene film before PLG. Monitoring of the spectral density of low-frequency voltage fluctuation (SU), which provides integral information about the system of defects and quality of the material, makes it possible to identify chips with low graphene quality and with inhomogeneously distributed areas of compressive stresses by the type of frequency dependence SU(f)
A Blueprint for the Synthesis and Characterization of Thiolated Graphene
Graphene derivatization to either engineer its physical and chemical properties or overcome the problem of the facile synthesis of nanographenes is a subject of significant attention in the nanomaterials research community. In this paper, we propose a facile and scalable method for the synthesis of thiolated graphene via a two-step liquid-phase treatment of graphene oxide (GO). Employing the core-level methods, the introduction of up to 5.1 at.% of thiols is indicated with the simultaneous rise of the C/O ratio to 16.8. The crumpling of the graphene layer upon thiolation without its perforation is pointed out by microscopic and Raman studies. The conductance of thiolated graphene is revealed to be driven by the Mott hopping mechanism with the sheet resistance values of 2.15 kΩ/sq and dependable on the environment. The preliminary results on the chemiresistive effect of these films upon exposure to ethanol vapors in the mix with dry and humid air are shown. Finally, the work function value and valence band structure of thiolated graphene are analyzed. Taken together, the developed method and findings of the morphology and physics of the thiolated graphene guide the further application of this derivative in energy storage, sensing devices, and smart materials