Load distribution on a closed-coupled wing canard at transonic speeds

A wind tunnel test where load distributions were obtained at transonic speeds on both the canard and wing surfaces of a closely coupled wing canard configuration is reported. Detailed component and configuration arrangement studies to provide insight into the various aerodynamic interference effects for the leading edge vortex flow conditions encountered are included. Data indicate that increasing the Mach number from 0.70 to 0.95 caused the wing leading edge vortex to burst over the wing when the wing was in the presence of the high canard

Aerodynamic load distributions at transonic speeds for a close-coupled wing-canard configuration: Tabulated pressure data

Wind tunnel studies are reported on both the canard and wing surfaces of a model that is geometrically identical to one used in several force and moment tests to provide insight into the various aerodynamic interference effects. In addition to detailed pressures measurements, the pressures were integrated to illustrate the effects of Mach number, canard location, and canard-wing interference on various aerodynamic parameters. Transonic pressure tunnel Mach numbers ranged from 0.70 to 1.20 for data taken from 0 deg to approximately 16 deg angle-of-attack at 0 deg sideslip

A study of canard-wing interference using experimental pressure data at transonic speeds

The canard had an exposed area of 28.0 percent of the wing reference area and was located in the chord plane of the wing or in a position 18.5 percent of the wing mean geometric chord above or below the wing chord plane. The canard leading edge sweep was 51.7 deg and the wing leading-edge sweep was 60 deg. The results indicated that the direct canard downwash effects on the wing loading are limited to the forward half of the wing directly behind the canard. The wing leading-edge vortex is located farther forward for the wing in the presence of the canard than for the wing-alone configuration. The wake, from the canard located below the wing chord plane, physically interacts with the wing inboard surface and produces a substantial loss of wing lift. For the Mach number 0.70 case, the presence of the wing increased the loading on the canard for the higher angles of attack. However, at Mach numbers of 0.95 and 1.20, the presence of the wing had the unexpected result of unloading the canard

The effect of wing dihedral and section suction distribution on vortex bursting

Eleven semi-span wing models were tested in the 1/8-scale model of the Langley V/STOL tunnel to qualitatively study vortex bursting. Flow visualization was achieved by using helium filled soap bubbles introduced upstream of the model. The angle of attack range was from 0 deg to 45 deg. The results show that the vortex is unstable, that is, the bursting point location is not fixed at a given angle of attack but moves within certain bounds. Upstream of the trailing edge, the bursting point location has a range of two inches; downstream, the range is about six inches. Anhedral and dihedral appear to have an insignificant effect on the vortex and its bursting point location. Altering the section suction distribution by improving the triangularity generally increases the angle of attack at which vortex bursting occurs at the trailing edge

Effect of wing-tip dihedral on the longitudinal and lateral aerodynamic characteristics of a supersonic cruise configuration at subsonic speeds

Force and moment data studies were conducted to determine the effect of wing-tip dihedral on the longitudinal and lateral aerodynamic characteristics of a supersonic cruise fighter configuration. Oil flow studies were also performed to investigate the model surface flow. Three models were tested: a flat (0 deg dihedral) wing tip, a dihedral, and an anhedral wing tip. The tests were conducted at the NASA Langley high-speed 7- by 10-foot wind tunnel

Boeing 747 aircraft with large external pod for transporting outsize cargo

The effect on structural arrangement, system weight, and range performance of the cargo pod payload carrying capability was determined to include either the bridge launcher or a spacelab module on a Boeing 747 aircraft. Modifications to the carrier aircraft and the installation time required to attach the external pod to the 747 were minimized. Results indicate that the increase in pod size was minimal, and that the basic 747 structure was adequate to safely absorb the load induced by ground or air operation while transporting either payload

Historical and Current Population Trends of Herring Gulls (\u3ci\u3eLarus argentatus\u3c/i\u3e) and Great Black-backed Gulls (\u3ci\u3eLarus marinus\u3c/i\u3e) in the New York Bight, USA

During the 20th century, gull populations in North America experienced considerable changes in abundance and geographic ranges. The objective of this study was to describe population trends of Herring Gulls (Larus argentatus) and Great Black-backed Gulls (L. marinus) in the New York Bight, USA, over a 40-year period (1974-2013). A variety of data sources using different survey methods provided estimates of the number of breeding pairs for both species. In the Long Island portion of the New York Bight, overall Herring and Great Black-backed gull nesting populations appear to have fluctuated considerably in size during this time period, and the largest numbers of breeding individuals of these two species occurred in the 1980s. In coastal New Jersey, the Herring Gull nesting population has remained relatively constant, whereas the Great Black-backed Gull nesting population has increased. Individual nesting colonies are dynamic and can vary in size considerably during even short time periods. Several factors, including sea-level changes and the availability of anthropogenic food sources (i.e., at landfills and fisheries by-catch), likely have strongly influenced individual colonies and the overall Herring and Great Blackbacked gull breeding populations in the New York Bight

Design of a large span-distributed load flying-wing cargo airplane with laminar flow control

A design study was conducted to add laminar flow control to a previously design span-distributed load airplane while maintaining constant range and payload. With laminar flow control applied to 100 percent of the wing and vertical tail chords, the empty weight increased by 4.2 percent, the drag decreased by 27.4 percent, the required engine thrust decreased by 14.8 percent, and the fuel consumption decreased by 21.8 percent. When laminar flow control was applied to a lesser extent of the chord (approximately 80 percent), the empty weight increased by 3.4 percent, the drag decreased by 20.0 percent, the required engine thrust decreased by 13.0 percent, and the fuel consumption decreased by 16.2 percent. In both cases the required take-off gross weight of the aircraft was less than the original turbulent aircraft

Preliminary design characteristics of a subsonic business jet concept employing laminar flow control

Aircraft configurations were developed with laminar flow control (LFC) and without LFC. The LFC configuration had approximately eleven percent less parasite drag and a seven percent increase in the maximum lift-to drag ratio. Although these aerodynamic advantages were partially offset by the additional weight of the LFC system, the LFC aircraft burned from six to eight percent less fuel for comparable missions. For the trans-atlantic design mission with the gross weight fixed, the LFC configuration would carry a greater payload for ten percent fuel per passenger mile