4 research outputs found
Phase transformations and thermal conductivity of the In-Ag alloys
Phase transformations and thermal conductivity of three In-Ag alloys with 5, 15, and 45 wt.% of Ag were experimentally investigated in the present work. Phase transition temperatures were measured using differential scanning calorimetry (DSC). DSC heating scans were compared with the equilibrium and non-equilibrium solidification paths, calculated by using optimized thermodynamic parameters from literature and calculation of phase diagrams (CALPHAD) method. The flash method was employed for the determination of thermal diffusivity and thermal conductivity of the investigated alloys in the temperature range from 25 to 100 °C. It has been found that an increase in silver content does not lead to an increase in the thermal conductivity of the investigated alloys. Thermal conductivities for all three investigated In-Ag alloys slightly decrease with temperature increasing
Study of microstructure and thermal properties of as-cast high carbon and high chromium tool steel
This work aims to investigate the microstructural and thermal properties of as-cast high carbon and high chromium cold work tool steel. The microstructure was investigated by using scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction (XRD) method. It was determined that at room temperature the microstructure of the investigated tool steel includes a lamellar network of M7C3 carbide precipitates along grain boundaries of ferrite grains in the base. Thermal diffusivity, specific heat capacity and thermal conductivity of the investigated steel alloy were determined in the temperature interval from 25 to 400 °C by using the laser-flash method. Thermal conductivity increases from 24.9 at 25 °C to 26.9 W/m·K at 400 °C. Phase transition temperatures in the temperature region from room temperature to 1250 °C were experimentally determined using differential scanning calorimetry (DSC). One endothermic effect in the temperature interval from 803 to 820 °C, corresponding to the ferrite/austenite phase transformation, was detected during sample heating. Experimental results were compared with the results of phase equilibria calculations obtained from the ThermoCalc software and TCFE6 database
The effect of silver addition on microstructure and thermal properties of the Cu–10%Al–8%Mn shape memory alloy
The influence of Ag addition on microstructure and thermal properties of the Cu-10%Al–8%Mn alloy was investigated in this work. Two alloys with designed compositions Cu-10%Al–8%Mn and Cu-10%Al–8%Mn-4%Ag (in wt.%) were prepared by induction melting of pure metals. Microstructures of the prepared samples were investigated in the as-cast state, after homogenization annealing and after quenching. The effects of different methods of heat treatment on the microstructure and transformation temperatures of the investigated Cu-10%Al–8%Mn and Cu-10%Al–8%Mn-4%Ag alloys were investigated using SEM-EDS and DSC techniques.It was determined that after induction melting microstructure of the both investigated alloys are primarily composed of martensite and a small amount of α-phase precipitates.Fully martensitic structure in both investigated alloys was obtained after direct quenching from the 850 °C into the ice water. Based on the DSC cooling curves it was determined that two-step martensite transformation for the both investigated alloys occur in the temperature interval from about 30 to -40 °C
The effect of silver addition on microstructure and thermal properties of the Cu–10%Al–8%Mn shape memory alloy
The influence of Ag addition on microstructure and thermal properties of the Cu-10%Al–8%Mn alloy was investigated in this work. Two alloys with designed compositions Cu-10%Al–8%Mn and Cu-10%Al–8%Mn-4%Ag (in wt.%) were prepared by induction melting of pure metals. Microstructures of the prepared samples were investigated in the as-cast state, after homogenization annealing and after quenching.
The effects of different methods of heat treatment on the microstructure and transformation temperatures of the investigated Cu-10%Al–8%Mn and Cu-10%Al–8%Mn-4%Ag alloys were investigated using SEM-EDS and DSC techniques.
It was determined that after induction melting microstructure of the both investigated alloys are primarily composed of martensite and a small amount of α-phase precipitates.
Fully martensitic structure in both investigated alloys was obtained after direct quenching from the 850 °C into the ice water. Based on the DSC cooling curves it was determined that two-step martensite transformation for the both investigated alloys occur in the temperature interval from about 30 to -40 °C