5,932 research outputs found
CFD Mixing Analysis of Jets Injected from Straight and Slanted Slots into Confined Crossflow in Rectangular Ducts
A CFD study was performed to analyze the mixing potential of opposed rows of staggered jets injected into confined crossflow in a rectangular duct. Three jet configurations were numerically tested: (1) straight (0 deg) slots; (2) perpendicular slanted (45 deg) slots angled in opposite directions on top and bottom walls; and (3) parallel slanted (45 deg) slots angled in the same direction on top and bottom walls. All three configurations were tested at slot spacing-to-duct height ratios (S/H) of 0.5, 0.75, and 1.0; a jet-to-mainstream momentum flux ratio (J) of 100; and a jet-to-mainstream mass flow ratio of 0.383. Each configuration had its best mixing performance at S/H of 0.75. Asymmetric flow patterns were expected and predicted for all slanted slot configurations. The parallel slanted slot configuration was the best overall configuration at x/H of 1.0 for S/H of 0.75
CFD mixing analysis of axially opposed rows of jets injected into confined crossflow
A computational fluid dynamics (CFD) parametric study was performed to analyze axially opposed rows of jets mixing with crossflow in a rectangular duct. Isothermal analysis was conducted to determine the influence of lateral geometric arrangement on mixing. Two lateral arrangements were analyzed: (1) inline (jets' centerlines aligned with each other on top and bottom walls), and (2) staggered (jets' centerlines offset with each other on top and bottom walls). For a jet-to-mainstream mass flow ratio (MR) of 2.0, design parameters were systematically varied for jet-to-mainstream momentum-flux ratios (J) between 16 and 64 and orifice spacing-to-duct height ratios (S/H) between 0.125 and 1.5. Comparisons were made between geometries optimized for S/H at a specified J. Inline configurations had a unique spacing for best mixing at a specified J. In contrast, staggered configurations had two 'good mixing' spacings for each J, one corresponding to optimum inline spacing and the other corresponding to optimum non-impinging jet spacing. The inline configurations, due to their smaller orifice size at optimum S/H, produced better initial mixing characteristics. At downstream locations (e.g. x/H of 1.5), the optimum non-impinging staggered configuration produced better mixing than the optimum inline configuration for J of 64; the opposite results were observed for J of 16. Increasing J resulted in better mixing characteristics if each configuration was optimized with respect to orifice spacing. Mixing performance was shown to be similar to results from previous dilution jet mixing investigations (MR less than 0.5)
Handbook for Learning-centred evaluation of Computer-facilitated learning projects in higher education
This handbook supports a project funded by the Australian Government Committee for University Teaching and Staff Development (CUTSD). The amended project title is “Staff Development in Evaluation of Technology-based Teaching Development Projects: An Action Inquiry Approach”.
The project is hosted by Murdoch University on behalf of the Australasian Society for Computers in Learning in Tertiary Education (ASCILITE), as a consortium of 11 universities.
The rationale of the project is to guide a group of university staff through the evaluation of a Computer-facilitated Learning (CFL1) project by a process of action inquiry and mentoring, supported by the practical and theoretical material contained in this handbook
On the predictions and limitations of the BeckerDoring model for reaction kinetics in micellar surfactant solutions
We investigate the breakdown of a system of micellar aggregates in a surfactant solution following an order-one dilution. We derive a mathematical model based on the Becker–Döring system of equations, using realistic expressions for the reaction constants fit to Molecular Dynamics simulations. We exploit the largeness of typical aggregation numbers to derive a continuum model, substituting a large system of ordinary differential equations for a partial differential equation in two independent variables: time and aggregate size. Numerical solutions demonstrate that re-equilibration occurs in two distinct stages over well-separated time-scales, in agreement with experiment and with previous theories. We conclude by exposing a limitation in the Becker–Döring theory for re-equilibration and discuss potential resolutions
An asymptotic theory for the re-equilibration of a micellar surfactant solution
Micellar surfactant solutions are characterized by a distribution of aggregates comprised predominantly of pre-micellar aggregates (monomers, dimers, trimers, etc.) and a region of proper micelles close to the peak aggregation number, connected by an intermediate region containing a very low concentration of aggregates. Such a distribution gives rise to a distinct two-timescale re-equilibration following a system dilution, known as the 1 and 2 processes, whose dynamics may be described by the Becker–Döring equations. We use a continuum version of these equations to develop a reduced asymptotic description that elucidates the behavior during each of these processes
The Occurrence of Autoimmune Diseases in Patients with Multiple Sclerosis and Their Families
The aims of this study were to determine whether the occurrence of autoimmune diseases is increased in patients with multiple sclerosis (MS) and their families and whether this is influenced by the type of MS. We conducted a case-control study using a questionnaire design to determine whether the prevalence of 11 autoimmune diseases is increased in patients with MS and their first-degree relatives compared to a random population control group and their first-degree relatives. We found that the total combined prevalence of the 11autoimmune diseases was higher in the MS patients than in the controls, with an odds ratio of 1.7 (95% confidence interval 0.9-3.2; P= 0.10) increasing to 1.9 (1.0-3.5; P= 0.05) after adjusting for age. For persons aged under 60 years, the odds ratio was 2.3 (1.1-4.6). We also found that there was a significant increase in the total combined prevalence of the autoimmune diseases in the first-degree relatives of MS patients compared to the first-degree relatives of the control group (P= 0.003, odds ratio 2.2, confidence interval 1.3-3.7). Patients with primary progressive MS did not differ from patients with relapsing-remitting or secondary progressive MS in the personal or familial occurrence of autoimmune disease. In conclusion, although there were sources of possible bias, this study suggests that individuals with MS have a genetic predisposition to autoimmunity in general
The structure of causal sets
More often than not, recently popular structuralist interpretations of
physical theories leave the central concept of a structure insufficiently
precisified. The incipient causal sets approach to quantum gravity offers a
paradigmatic case of a physical theory predestined to be interpreted in
structuralist terms. It is shown how employing structuralism lends itself to a
natural interpretation of the physical meaning of causal sets theory.
Conversely, the conceptually exceptionally clear case of causal sets is used as
a foil to illustrate how a mathematically informed rigorous conceptualization
of structure serves to identify structures in physical theories. Furthermore, a
number of technical issues infesting structuralist interpretations of physical
theories such as difficulties with grounding the identity of the places of
highly symmetrical physical structures in their relational profile and what may
resolve these difficulties can be vividly illustrated with causal sets.Comment: 19 pages, 4 figure
Flow Coupling Effects in Jet-in-Crossflow Flowfields
The combustor designer is typically required to design liner orifices that effectively mix air jets with crossflow effluent. CFD combustor analysis is typically used in the design process; however the jets are usually assumed to enter the combustor with a uniform velocity and turbulence profile. The jet-mainstream flow coupling is usually neglected because of the computational expense. This CFD study was performed to understand the effect of jet-mainstream flow coupling, and to assess the accuracy of jet boundary conditions that are commonly used in combustor internal calculations. A case representative of a plenum-fed quick-mix section of a Rich Burn/Quick Mix/Lean Burn combustor (i.e. a jet-mainstream mass-flow ratio of about 3 and a jet-mainstream momentum-flux ratio of about 30) was investigated. This case showed that the jet velocity entering the combustor was very non-uniform, with a low normal velocity at the leading edge of the orifice and a high normal velocity at the trailing edge of the orifice. Three different combustor-only cases were analyzed with uniform inlet jet profile. None of the cases matched the plenum-fed calculations. To assess liner thickness effects, a thin-walled case was also analyzed. The CFD analysis showed the thin-walled jets had more penetration than the thick-walled jets
- …