Smart SQUIDs based on Relaxation Oscillation SQUIDs

Smart SQUIDs based on double Relaxation Oscillation SQUIDs (DROS) and a superconducting up-down counter have been developed. DROS and counter form a flux locked loop on one single chip. The DROS output consists of a series of pulses that controls the two up and down write gates of the counter. The pulsed output structure of the DROS constitutes the internal clock for this single-chip device. Several prototypes were built with a clock frequency of 100 MHz, a linear operation flux range of about 2.5 ¿0, and a white noise level of 6.5 ¿¿0/¿Hz. The smart SQUID is in principle a promising device for application in multichannel SQUID system

Monolithic flux transformer-coupled high-Tc dc SQUID magnetometers

YBa/sub 2/Cu/sub 3/O/sub 7-x/ based monolithic flux transformer-coupled high-T/sub c/ DC SQUID magnetometers operating up to 73 K have been realized. The devices are characterized by high values of the modulation voltage, up to 32 /spl mu/V at 40 K. A minimal white noise level of 0.10 pT//spl radic/Hz was obtained above 200 Hz, and 0.64 pT//spl radic/Hz at 1 Hz and 55 K. The temperature dependence of the modulation voltage, the effective sensing area and the field sensitivity are discussed. Model-calculations have been performed to investigate high frequency resonances in the washer-input coil structure. Methods for damping are considered

The use of (double) relaxation oscillation SQUIDs as a sensor

Relaxation Oscillation SQUIDs (ROSs) and Double Relaxation Oscillation SQUIDs (DROSs) are based on relaxation oscillations that are induced in hysteretic dc SQUIDs by an external L-R shunt. The relaxation frequency of a ROS varies with the applied flux Φ, whereas the output of a DROS is a dc voltage, with a typical flux-to-voltage transfer of ∂V/∂Φ≈1 mV/Φ0. The flux-to-frequency response of several ROSs has been measured and compared with theory for frequencies up to 7 GHz. Various DROS designs-a multi-loop direct coupling DROS, a DROS with a washer type signal SQUID and a DROS with gradiometric signal SQUID-will be discussed in this paper. The integration of a DROS with a digital flux locked loop (“Smart DROS”) will also be analyze

Laser scanning imaging and local characterization of superconducting properties in high-Tc thin film multiturn coil

Low-temperature scanning laser microscopy has been used to investigate the spatial variation of the critical temperature Tc and critical current Ic in thin-film high-Tc multilayer structures that include dielectric layers. The method is described and measurements are presented on an YBa2Cu3O7-x-based multiturn coil with SrTiO3 insulating layer. We found that the critical temperature Tc of the YBa2Cu3O7-x top layer, from which the return strip of the coil is formed, is higher than that of the YBa2Cu3O7-x base layer. The critical current of the coil is limited by the quality of the YBa2Cu3O7-x base layer and not by the edges of the crossovers

A 1-MHz low noise preamlifier based on Double Relaxation Oscillation SQUIDs

A low noise and wideband preamplifier based on Double Relaxation Oscillation Superconducting Quantum Interference Devices (DROSs) has been realized. A major advantage of a DROS is that it can be operated in a simple flux modulation. So far, biomagnetic measurements performed in our group required only a limited bandwidth smaller than 100 kHz. Other applications, like for instance readout of radiation and particle detectors, demand a larger bandwidth. In this paper, we will discuss our efforts aimed at increasing the operational bandwidth of a DROS in flux locked loop. Presently, a flux locked loop scheme with a -3 dB bandwidth of 1.45 MHz has been built. With this system a white flux noise of 8 ¿¿0/¿Hz was measured with a 1/f-corner frequency of 10 Hz. The slew rate was 2.5·105 ¿0/s. With the mutual input inductance of 6.7 nH, an input current noise of the preamplifier of 2.5 pA/¿Hz was found and a current slew rate of 80 mA/s. We will discuss the suitability of our DROS-based preamplifier for readout of cryogenic particle detectors based on superconducting tunnel junction

Four layer monolithic integrated high Tc dc SQUID magnetometer

YBa2Cu3O7−x based monolithic integrated dc SQUID magnetometers, consisting of a dc SQUID integrated with a flux transformer on a single bicrystalline substrate, have been fabricated and characterized. The devices consist of four layers, including two superconducting layers, and first realizations operate up to 73 K. A maximum voltage modulation of 32 μV is observed at 40 K. A field sensitivity of 0.17 pT/√Hz is obtained above 200 Hz at 45 K and 0.49 pT/√Hz at 1 Hz and 65 K

Development of Cryogenic Current Comparators with DC Squid Readout for the Calibration of Electrical Standards

For the realization of the electrical quantum metrology triangle (V-A-Ω) a device to amplify very small currents with high precision is needed. The cryogenic current comparator (CCC) is by far the best instrument to do this. In order to make a very current sensitive CCC for calibration of electrical standards, we have developed optimum dc Superconducting QUantum Interference Devices (SQUIDs). The design, fabrication and characterisation of these devices is presented. The measurements concern the flux-to-voltage transfer and the noise properties, especially the input current noise. The optimisation of the flux transformer circuit that links the CCC with the SQUID will be treated. In addition, typical fabrication aspects of the CCC as the wires and tube assembly, the shields and the support system will be addressed