One application of mega-geomorphology in education

One advantage of a synoptic view displaying landform assemblages provided by imagery is that one can often identify geomorphic processes which have shaped the region and which may affect the habitability of the area over a human life time. Considering the continued growth of the world population and the resultant pressure and the exploitation of land, usually without any consideration given to geologic processes, it is imperative that we attempt to educate as large a segment of the population as we can about geologic processes and how they influence land use. Space platform imagery which exhibits regional landscapes can be used: (1) to show students the impact of geologic processes over relatively short periods of time (e.g., the Mount St. Helens lateral blast); (2) to display the effects of poor planning because of a lack of knowledge of the local geologic processes (e.g., the 1973 image of the Mississippi River flood around St. Louis, MO); and (3) to show the association of certain types of landforms with building materials and other resources (e.g., drumlins and gravel deposits)

Supersonic axial-force characteristics of a rectangular-box cavity with various length-to-depth ratios in a flat plate

A wind-tunnel investigation has been conducted at Mach numbers of 1.50, 2.16, and 2.86 to obtain axial-force data on a metric rectangular-box cavity with various length-to-depth ratios. The model was tested at angles of attack from -4 deg to -2 deg. The results are summarized to show variations in cavity axial-force coefficient for deep- and shallow-cavity configurations with detached and attached cavity flow fields, respectively. The results of the investigation indicate that for a wide range of cavity lengths and depths, good correlations of the cavity axial-force coefficients (based on cavity rear-face area) are obtained when these coefficients are plotted as a function of cavity length-to-depth ratio. Abrupt increases in the cavity axial-force coefficients at an angle of attack of 0 deg. reflect the transition from an open (detached) cavity flow field to a closed (attached) cavity flow field. Cavity length-to-depth ratio is the dominant factor affecting the switching of the cavity flow field from one type to the other. The type of cavity flow field (open or closed) is not dependent on the test angles of attack except near the critical value of length-to-depth ratio

Digital multishaker modal testing

A review of several modal testing techniques is made, along with brief discussions of their advantages and limitations. A new technique is presented which overcomes many of the previous limitations. Several simulated experiments are included to verify the validity and accuracy of the new method. Conclusions are drawn from the simulation studies and recommendations for further work are presented. The complete computer code configured for the simulation study is presented

DEFINING AND MEASURING RURALITY

Community/Rural/Urban Development,

ESTIMATING THE RELATIVE RURALITY OF U.S. COUNTIES

Community/Rural/Urban Development,

A Comparison of staggered position one angle process color printing with four angle and one angle process color printing

The Staggered Position One Angle method of preparing color separations does not adjust the dot angle for each color. The dot pattern is staggered horizontally or vertically by half a row of dots for each separation maintaining the same angle. The investigation compared the Staggered Position method to the four angle method and to the dot-on-dot method. Newsprint was the substrate, and 65, 85, and 100 lines per inch were the rulings. Experienced judges viewed the representative prints and scored each for sharpness, color variability, and overall acceptance. They were also asked to indicate the evidence of rosette and moire patterns. Densitometric and spectrophotometer readings were used for objective analysis. The judges found the Staggered Position to be equal or better than both four angle and dot-on-dot printing in most instances. A non existant rosette pattern and a minimal risk of moire\u27 patterns also resulted. The Staggered Position printing excelled in the ability to produce a sharp reproduction, and its tone reproduction was found to be equivalent to the four angle and dot-on-dot printing. The use of Delta E for the visual rejection or acceptance of an image was found not to be a good indicator in this particular study. The study opens up a number of areas for further research into this new separation method, but because of its good performance on newsprint, it should be considered as an alternative to the four angle method for newspapers

Effect of tail-fin span on stability and control characteristics of a Canard-controlled missile at supersonic Mach numbers

An experimental wind-tunnel investigation was conducted at Mach numbers from 1.60 to 3.50 to obtain the longitudinal and lateral-directional aerodynamic characteristics of a circular, cruciform, canard-controlled missile with variations in tail-fin span. In addition, comparisons were made with the experimental aerodynamic characteristics using three missile aeroprediction programs: MISSILE1, MISSILE2, and NSWCDM. The results of the investigation indicate that for the test Mach number range, canard roll control at low angles of attack is feasible on tail-fin configurations with tail-to-canard span ratios of less than or equal to 0.75. The conards are effective pitch and yaw control devices on each tail-fin span configuration tested. Programs MISSILE1 and MISSILE2 provide very good predictions of longitudinal aerodynamic characteristics and fair predictions of lateral-directional aerodynamic characteristics at low angles of attack, with MISSILE2 predictions generally in better agreement with test data. Program NSWCDM provides good longitudinal and lateral-directional aerodynamic predictions that improve with increases in tail-tin span

Re-design and fabrication of titanium multi-wall Thermal Protection System (TPS) test panels

The Titanium Multi-wall Thermal Protection System (TIPS) panel was re-designed to incorporate Ti-6-2-4-2 outer sheets for the hot surface, ninety degree side closures for ease of construction and through panel fastness for ease of panel removal. Thermal and structural tests were performed to verify the design. Twenty-five panels were fabricated and delivered to NASA for evaluation at Langley Research Center and Johnson Space Center