The ABC130 barrel module prototyping programme for the ATLAS strip tracker

For the Phase-II Upgrade of the ATLAS Detector, its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100 % silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-25) and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests.Comment: 82 pages, 66 figure

Interpretation of Calcaneus Dual-Energy X-Ray Absorptiometry Measurements in the Assessment of Osteopenia and Fracture Risk

ABSTRACT Dual-energy X-ray absorptiometry (DXA) of the calcaneus is useful in assessing bone mass and fracture risk at other skeletal sites. However, DXA yields an areal bone mineral density (BMD) that depends on both bone apparent density and bone size, potentially complicating interpretation of the DXA results. Information that is more complete may be obtained from DXA exams by using a volumetric density in addition to BMD in clinical applications. In this paper, we develop a simple methodology for determining a volumetric bone mineral apparent density (BMAD) of the calcaneus. For the whole calcaneus, BMAD ‫؍‬ (BMC)/A DXA 3/2 , where BMC and A DXA are, respectively, the bone mineral content and projected area measured by DXA. We found that A DXA 3/2 was proportional to the calcaneus volume with a proportionality constant of 1.82 ؎ 0.02 (mean ؎ SE). Consequently, consistent with theoretical predictions, BMAD was proportional to the true volumetric apparent density () of the bone according to the relationship ‫؍‬ 1.82 BMAD. Also consistent with theoretical predictions, we found that BMD varied in proportion to V 1/3 , where V is the bone volume. We propose that the volumetric apparent density, estimated at the calcaneus, provides additional information that may aid in the diagnosis of osteopenia. Areal BMD or BMD 2 may allow estimation of the load required to fracture a bone. Fracture risk depends on the loading applied to a bone in relation to the bone's failure load. When DXA is used to assess osteopenia and fracture risk in patients, it may be useful to recognize the separate and combined effects of applied loading, bone apparent density, and bone size. (J Bone Miner Res 2000;15:1573-1578

The ABC130 barrel module prototyping programme for the ATLAS strip tracker

For the Phase-II Upgrade of the ATLAS Detector [1], its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100% silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-250) [2,2] and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests