294 research outputs found

    Label-free, single molecule detection of cytokines using optical microcavities

    Get PDF
    Interleukin-2 (IL2) is a cytokine that regulates T-cell growth and is used in cancer therapies. By sensitizing a microcavity sensor surface with anti-IL2 and monitoring the resonant frequency, single molecules of IL2 can be detected

    Electrical thermo-optic tuning of ultrahigh-Q microtoroid resonators

    Get PDF
    The ability to tune resonant frequency in optical microcavities is an essential feature for many applications. Integration of electrical-based tuning as part of the fabrication process has been a key advantage of planar microresonant devices. Until recently, the combination of these features has not been available in devices that operate in the ultrahigh-Q regime where device quality factors (Q) can exceed 100 million. In this letter, we demonstrate an electrically tunable resonator on a chip with ultrahigh-quality factors. Futhermore, the devices have demonstrated tuning rates in excess of 85 GHz/V2 and are capable of tuning more than 300 GHz

    Label-free detection of cytokines using optical microcavities

    Get PDF
    Ultra-high-Q microresonators have demonstrated sensitive and specific chemical and biological detection. The sensitivity is derived from the long photon lifetime inside the cavity and specificity is achieved through surface functionalization. Here, ultra-high-Q microcavities demonstrate label-free, single molecule detection of Interleukin-2 (IL-2) in fetal bovine serum (FBS). IL-2 is a cytokine released in response to immune system activation. The surface of the microtoroids was sensitized using anti-IL-2. The detection mechanism relies upon a thermo-optic mechanism to enhance resonant wavelength shifts induced through binding of a molecule

    Chemical and biological detectors using ultra-high-Q microresonators

    Get PDF
    Recently, a method for fabricating planar arrays of optical microtoroid resonators with quality factors greater than 500 million was developed. These devices have previously demonstrated Raman and OPO lasing and radiation pressure induced oscillations. When immersed in an aqueous environment, these devices are able to maintain their ultra-high Q factors by operating in the visible wavelength band, enabling very sensitive chemical and biological detection. The fabrication and optical properties of these devices will be described. These devices have performed both chemical and biological detection. Systems which have been detected include D_2O in water and a variety of biological molecules. Sensitivity limits will also be discussed

    Portable Polarimetric Fiber Stress Sensor System for Visco-elastic and Biomimetic Material Analysis

    Get PDF
    Non-destructive materials characterization methods have significantly changed our fundamental understanding of material behavior and have enabled predictive models to be developed. However, the majority of these efforts have focused on crystalline and metallic materials, and transitioning to biomaterials, such as tissue samples, is non-trivial, as there are strict sample handling requirements and environmental controls which prevent the use of conventional equipment. Additionally, the samples are smaller and more complex in composition. Therefore, more advanced sample analysis methods capable of operating in these environments are needed. In the present work, we demonstrate an all-fiber-based material analysis system based on optical polarimetry. Unlike previous polarimetric systems which relied on free-space components, our method combines an in-line polarizer, polarization-maintaining fiber, and a polarimeter to measure the arbitrary polarization state of the output, eliminating all free-space elements. Additionally, we develop a more generalized theoretical analysis which allows more information about the polarization state to be obtained via the polarimeter. We experimentally verify our system using a series of elastomer samples made from polydimethylsiloxane (PDMS), a commonly used biomimetic material. By adjusting the base:curing agent ratio of the PDMS, we controllably tune the Young’s modulus of the samples to span over an order of magnitude. The measured results are in good agreement with those obtained using a conventional load-frame system. Our fiber-based polarimetric stress sensor shows promise for use as a simple research tool that is portable and suitable for a wide variety of applications

    Spatiotemporal Fluorescent Detection Measurements Using Embedded Waveguide Sensors

    Get PDF
    Integrated waveguide biosensors, when combined with fluorescent labeling, have significantly impacted the field of biodetection. While there are numerous types of waveguide sensors, the fundamental excitation method is fairly consistent: the evanescent field of the waveguide excites a fluorophore whose emission is detected, either directly via imaging or indirectly via a decrease in power transfer. Recently, a sensor device was demonstrated which is able to back-couple the emitted light into the waveguide, allowing the signal to be detected directly. However, this previous work focused on the development of an empirical model, leaving many theoretical questions unanswered. Additionally, the results from the novel back-coupling route were not compared with the results from the more conventional imaging technique. In this study, we develop finite difference time domain simulations to predict the sensor\u27s performance both in air and aqueous environments. We also perform complementary experiments to verify the modeling, measuring the fluorescence coupled into the waveguide, and radiated perpendicular to the waveguide. Finally, we performed spatiotemporal measurements of the fluorescence on the waveguide. Utilizing these measurements, we are able to measure the fluorescent decay rate of the fluorescent dye at arbitrary points along the length of the waveguide

    Indagine sulle buone pratiche di gestione nella preparazione di prodotti a base di pesce crudo

    Get PDF
    L’aumentata richiesta di prodotti ittici da parte del consumatore, insieme all’esigenza di “freschezza” e praticità di utilizzo, hanno consacrato Sushi e sashimi, prodotti a base di pesce crudo tipici della cucina giapponese, fra quelli più apprezzati e richiesti dal mercato. Purtroppo questa tipologia di ristorazione etnica, in continuo aumento sul nostro territorio, non è sempre gestita da operatori di origine giapponese ma da operatori cinesi, grazie alla facile riconversione. Tali prodotti, in relazione alle modalità di preparazione, presentazione e distribuzione, sono però caratterizzati da specifiche problematiche di natura sanitaria. In particolar modo, il rischio parassitologico, legato alla presenza di larve di Anisakis spp in questi alimenti non trattati termicamente, richiede una attenta gestione del prodotto ed una formazione mirata del personale addetto alla sua preparazione. L’indagine effettuata in questo lavoro, in pieno accordo con quanto richiesto da una nota del 2009 del Ministero della Salute, nella quale si chiedeva espressamente che alle AA. UU. SS. LL. competenti di effettuare i controlli necessari per la valutazione dell’avvenuto congelamento previsto dal REG (CE) 853/2004, ha avuto lo scopo, attraverso la somministrazione di un questionario, di delineare le principali criticità legate agli esercizi di preparazione e somministrazione di prodotti a base di pesce crudo. I risultati evidenziano come la mancanza si formazione sia alla base di una cattiva gestione del rischio parassitologico soprattutto in relazione all’utilizzo di parametri tempo/temperatura non conformi a quanto prescritto dalla normativa
    • …
    corecore