19 research outputs found

    Costs Associated with Low Birth Weight in a Rural Area of Southern Mozambique

    Get PDF
    BACKGROUND: Low Birth Weight (LBW) is prevalent in low-income countries. Even though the economic evaluation of interventions to reduce this burden is essential to guide health policies, data on costs associated with LBW are scarce. This study aims to estimate the costs to the health system and to the household and the Disability Adjusted Life Years (DALYs) arising from infant deaths associated with LBW in Southern Mozambique. METHODS AND FINDINGS: Costs incurred by the households were collected through exit surveys. Health system costs were gathered from data obtained onsite and from published information. DALYs due to death of LBW babies were based on local estimates of prevalence of LBW (12%), very low birth weight (VLBW) (1%) and of case fatality rates compared to non-LBW weight babies [for LBW (12%) and VLBW (80%)]. Costs associated with LBW excess morbidity were calculated on the incremental number of hospital admissions in LBW babies compared to non-LBW weight babies. Direct and indirect household costs for routine health care were 24.12 US(CI95 (CI 95% 21.51; 26.26). An increase in birth weight of 100 grams would lead to a 53% decrease in these costs. Direct and indirect household costs for hospital admissions were 8.50 US (CI 95% 6.33; 10.72). Of the 3,322 live births that occurred in one year in the study area, health system costs associated to LBW (routine health care and excess morbidity) and DALYs were 169,957.61 US$ (CI 95% 144,900.00; 195,500.00) and 2,746.06, respectively. CONCLUSIONS: This first cost evaluation of LBW in a low-income country shows that reducing the prevalence of LBW would translate into important cost savings to the health system and the household. These results are of relevance for similar settings and should serve to promote interventions aimed at improving maternal care

    Mineral loss and color change of enamel after bleaching and staining solutions combination

    No full text
    Pigments of food and beverages could affect dental bleaching efficacy. The aim of this investigation was to evaluate color change and mineral loss of tooth enamel as well as the influence of staining solutions normally used by adolescent patients undergoing home bleaching. Initial hardness and baseline color were measured on enamel blocks. Specimens were divided into five groups (n = 5): G1 (control) specimens were kept in artificial saliva throughout the experiment (3 weeks); G2 enamel was exposed to 10% carbamide peroxide for 6 h daily, and after this period, the teeth were cleaned and stored in artificial saliva until the next bleaching session; and G3, G4, and G5 received the same treatments as G2, but after bleaching, they were stored for 1 h in cola soft drink, melted chocolate, or red wine, respectively. Mineral loss was obtained by the percentage of hardness reduction, and color change was determined by the difference between the data obtained before and after treatments. Data were subjected to analysis of variance and Fisher's test (a = 0.05). G3 and G5 showed higher mineral loss (92.96 +/- 5.50 and 94.46 +/- 1.00, respectively) compared to the other groups (p = 0.05). G5 showed high-color change (9.34 +/- 2.90), whereas G1 presented lower color change (2.22 +/- 0.44) (p = 0.05). Acidic drinks cause mineral loss of the enamel, which could modify the surface and reduce staining resistance after bleaching. (C) 2013 Society of Photo-Optical Instrumentation Engineers (SPIE)181

    Influence of voids in the hybrid layer based on self-etching adhesive systems: a 3-D FE analysis

    No full text
    The presence of porosities at the dentin/adhesive interface has been observed with the use of new generation dentin bonding systems. These porosities tend to contradict the concept that etching and hybridization processes occur equally and simultaneously. Therefore, the aim of this study was to evaluate the micromechanical behavior of the hybrid layer (HL) with voids based on a self-etching adhesive system using 3-D finite element (FE) analysis. MATERIAL AND METHODS: Three FE models (Mr) were built: Mr, dentin specimen (41x41x82 μm) with a regular and perfect (i.e. pore-free) HL based on a self-etching adhesive system, restored with composite resin; Mp, similar to M, but containing 25% (v/v) voids in the HL; Mpp, similar to Mr, but containing 50% (v/v) voids in the HL. A tensile load (0.03N) was applied on top of the composite resin. The stress field was obtained by using Ansys Workbench 10.0. The nodes of the base of the specimen were constrained in the x, y and z axes. The maximum principal stress (σmax) was obtained for all structures at the dentin/adhesive interface. RESULTS: The Mpp showed the highest peak of σmax in the HL (32.2 MPa), followed by Mp (30 MPa) and Mr (28.4 MPa). The stress concentration in the peritubular dentin was high in all models (120 MPa). All other structures positioned far from voids showed similar increase of stress. CONCLUSION: Voids incorporated into the HL raised the σmax in this region by 13.5%. This behavior might be responsible for lower bond strengths of self-etching and single-bottle adhesives, as reported in the literature
    corecore