Study on the Effect of Laser Welding Parameters on the Microstructure and Mechanical Properties of Ultrafine Grained 304L Stainless Steel

In the present study, an ultrafine grained (UFG) 304L stainless steel with the average grain size of 300 nm was produced by a combination of cold rolling and annealing. Weldability of the UFG sample was studied by Nd: YAG laser welding under different welding conditions. Taguchi experimental design was used to optimize the effect of frequency, welding time, laser current and laser pulse duration on the resultant microstructure and mechanical properties. X-ray Diffraction (XRD), Optical Microscope (OM), Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM), microhardness measurements and tension tests were conducted to characterize the sample after thermomechanical processing and laser welding. The results showed that the ultrafine grained steel had the yield strength of 1000 Mpa and the total elongation of 48%, which were almost three times higher than those of the as-received sample. The microstructure of the weld zone was shown to be a mixture of austenite and delta ferrite. The microhardness of the optimized welded sample (315 HV0.5) was found to be close to the UFG base metal (350 HV). It was also observed that the hardness of the heat affected zone (HAZ) was  lower than that of the weld zone, which was related to the HAZ grain growth during laser welding. The results of optimization also showed that the welding time was the most important parameter affecting the weld strength. Overall, the study showed that laser welding could be an appropriate and alternative welding technique for the joining of UFG steels

Failure Analysis of Two HP-Nb Heat-Resistant Tubes after 46,000 h Exposure to Reformer Service Conditions

This study presents a failure analysis in two reformer tubes used for hydrogen production in a petrochemical industry. These tubes (Tube A and Tube B) were made by the centrifugal casting of HP-Nb alloy in such a way that one contained titanium as a micro-element, and the other was free from titanium in its chemical composition. Although the two tubes were subjected to similar creep conditions, Tube A failed after only 46,000 h of operation against the design life of 100,000 h. SEM images showed initiation and growth of creep pores next to chromium carbide particles, as well as the formation of microcracks in Cr23C6 carbides. Pore initiation occurs as a result of grain boundary sliding and is strongly dependent on structural morphology. The tube containing titanium (Tube B) showed higher thermal stability and higher creep resistance than the tube without titanium (Tube A), which was due to the formation of finer and more discrete carbide particles. The final fracture of the tube without titanium (Tube A) occurred due to the coalescence of creep pores and the creation of grain boundary cracks

Failure Analysis of Two HP-Nb Heat-Resistant Tubes after 46,000 h Exposure to Reformer Service Conditions

This study presents a failure analysis in two reformer tubes used for hydrogen production in a petrochemical industry. These tubes (Tube A and Tube B) were made by the centrifugal casting of HP-Nb alloy in such a way that one contained titanium as a micro-element, and the other was free from titanium in its chemical composition. Although the two tubes were subjected to similar creep conditions, Tube A failed after only 46,000 h of operation against the design life of 100,000 h. SEM images showed initiation and growth of creep pores next to chromium carbide particles, as well as the formation of microcracks in Cr23C6 carbides. Pore initiation occurs as a result of grain boundary sliding and is strongly dependent on structural morphology. The tube containing titanium (Tube B) showed higher thermal stability and higher creep resistance than the tube without titanium (Tube A), which was due to the formation of finer and more discrete carbide particles. The final fracture of the tube without titanium (Tube A) occurred due to the coalescence of creep pores and the creation of grain boundary cracks.Electronic Components, Technology and Material