Mechanical properties of carbon nanotube fibres: St Venant's principle at the limit and the role of imperfections

Carbon nanotube (CNT) fibres, especially if perfect in terms of purity and alignment, are of extreme anisotropy. With their high axial strength but ready slippage between the CNTs, there is utmost difficulty in transferring the force applied uniformly. Finite element analysis is used to predict the stress distribution in CNT fibres loaded by grips attached to their surface, along with the resulting tensile stress-strain curves. This study demonstrates that in accordance with St Venant’s principle very considerable length-to-diameter ratios (~ 103) are required before the stress becomes uniform across the fibre, even at low strains. It is proposed that lack of perfect orientation and presence of carbonaceous material between bundles greatly enhances the stress transfer, thus increasing the load it can carry before failing by shear. It is suggested that a very high strength batch of fibres previously observed experimentally had an unusually high concentration of internal particles, meaning that the pressure exerted by the grips would assist stress transfer between the layers. We conclude, that the strength of CNT fibres depends on the specific testing geometries and that imperfections, whether by virtue of less-than-perfect orientation or of embedded impurities, are actually major positive contributors to the observed strength.The authors are grateful to USN ONR GLOBAL for the provision of funding under award number N62909-14-1-N200. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the Office of Naval Research.This is the accepted manuscript. The final version is available at http://www.sciencedirect.com/science/article/pii/S0008622315004728

Mapping the parameter space for direct-spun carbon nanotube aerogels

Industrial-scale use of carbon nanotube (CNT) materials and prototype development is limited by availability of economic, high throughput production methods. Recent investigations have demonstrated the feasibility of producing direct-spun macroscopic CNT materials via floating catalyst chemical vapour deposition. However, few quantitative results have been reported regarding process yield and correlations with product quality. Validation of results is therefore challenging as identification of the key fundamental process parameters is hindered. This first meta-analysis quantifies atomic input rates and correlates them with product outputs to map the current parameter space of 55 successful conditions leading to spinnable aerogels. All mapped processes fall within a bulk residence time of 5–240 s, operating temperature of 1100–1500°C and an atomic S:Fe of 0.1–10. Low (high) S/Fe ratios favour single (multi)-wall CNTs in the direct-spun product. A high atomic carbon dilution, only 3% of the input atoms being C, is a common feature across many systems. Furthermore, we connect the findings to known catalyst and product growth behaviour, as well as the thermodynamics of intermediates, to create an emerging picture of direct-spun CNT product formation. Elucidation of the most important factors influencing material synthesis, and the relationships between them, provides opportunities for gains in industrial-scale synthesi

Triboluminescence flashes from high-speed ruptures in carbon nanotube Macro-Yarns

© 2017 During tensile tests of carbon nanotube (CNT) macrostructures (ribbons, ropes and tows) under dynamic strain rates (1000 s –1 ), we recorded temporally sporadic, spatially localized visible light emissions (“flashes”) of less than 1.5 µs duration. The flashes occurred at the fracture sites and were, depending on the sample morphology, either distributed randomly over time (for tows) or occurred all at once over larger areas of several pixels (for ribbons). In situ thermal camera measurements, as well as ex situ analysis by electron microscopy reveal a hierarchical mechanism of overall heating over the whole sample length during straining, and localized heating around the fracture surfaces. Temperatures around the fracture tip were calculated to be of 1800 K in average. We propose that the flashes are caused by charge separation due to CNT bond fracture and gas discharge of the surrounding gases. Triboluminescence, known for larger sugar crystals, has not been observed for carbon nanotubes previously. It results from the yarn-like morphology, the ultra-high strength and thermal conductivity of our CNT fibers, which at high strain rates concentrate the strain at CNT level and lead to CNT fracture, rather than bundle sliding

High thermal conductivities of carbon nanotube films and micro-fibres and their dependence on morphology

Thermal conductivity of carbon nanotube (CNT) films and micro-fibres synthesised by floating catalyst chemical vapour deposition was measured by the parallel thermal conductance method. CNT films showed in-plane thermal conductivities of 110 W m⁻¹ K⁻¹. Online condensation into a micro-fibre morphology – a two-dimensional reduction in the transverse plane, including some axial stretching during solvent evaporation – resulted in room-temperature thermal conductivity values as high as 770 ± 10 W m⁻¹ K⁻¹, which is the highest thermal conductivity reported for CNT bulk materials to date. In specific terms, this matches the maximum thermal conductivity of heat-treated carbon fibre, but with a higher onset temperature for Umklapp scattering processes (300 K rather than 150 K). We selected four sample types to investigate effects of alignment, purity, and single- or multi-wall character on their thermal conductivity. For both the electrical and thermal conductivity of as-spun material, i.e. without any post-synthesis treatment, we show that the density and quality of CNT bundle alignment are still the predominant factors affecting these properties, outweighing the influence of single- or multi-walled character of the nanotubes. This raises the promise that, with optimal alignment and junction points, even higher values of thermal conductivity are achievable for macroscopic CNT fibres.We also acknowledge the US Office of Naval Research (W911NF-11-1-0250) and ONR Global (N62909-15-1-2034) for funding and support. The work at Dalhousie University was supported by NSERC (RGPIN-2015-04593), as well as the Canada Foundation for Innovation, Atlantic Innovation Fund, Dalhousie University and other partners that fund the Facilities for Materials Characterisation managed by the Institute for Research in Materials

Assessment of ABT-263 activity across a cancer cell line collection leads to a potent combination therapy for small-cell lung cancer

BH3 mimetics such as ABT-263 induce apoptosis in a subset of cancer models. However, these drugs have shown limited clinical efficacy as single agents in small-cell lung cancer (SCLC) and other solid tumor malignancies, and rational combination strategies remain underexplored. To develop a novel therapeutic approach, we examined the efficacy of ABT-263 across >500 cancer cell lines, including 311 for which we had matched expression data for select genes. We found that high expression of the proapoptotic gene Bcl2-interacting mediator of cell death (BIM) predicts sensitivity to ABT-263. In particular, SCLC cell lines possessed greater BIM transcript levels than most other solid tumors and are among the most sensitive to ABT-263. However, a subset of relatively resistant SCLC cell lines has concomitant high expression of the antiapoptotic myeloid cell leukemia 1 (MCL-1). Whereas ABT-263 released BIM from complexes with BCL-2 and BCL-XL, high expression of MCL-1 sequestered BIM released from BCL-2 and BCL-XL, thereby abrogating apoptosis. We found that SCLCs were sensitized to ABT-263 via TORC1/2 inhibition, which led to reduced MCL-1 protein levels, thereby facilitating BIM-mediated apoptosis. AZD8055 and ABT-263 together induced marked apoptosis in vitro, as well as tumor regressions in multiple SCLC xenograft models. In a Tp53; Rb1 deletion genetically engineered mouse model of SCLC, the combination of ABT-263 and AZD8055 significantly repressed tumor growth and induced tumor regressions compared with either drug alone. Furthermore, in a SCLC patient-derived xenograft model that was resistant to ABT-263 alone, the addition of AZD8055 induced potent tumor regression. Therefore, addition of a TORC1/2 inhibitor offers a therapeutic strategy to markedly improve ABT-263 activity in SCLC.United States. Dept. of Defense (Grant W81-XWH-13-1-0323)National Cancer Institute (U.S.) (Cancer Center Support Grant P30-CA14051

A systematic review of longitudinal studies on the association between depression and smoking in adolescents

<p>Abstract</p> <p>Background</p> <p>It is well-established that smoking and depression are associated in adolescents, but the temporal ordering of the association is subject to debate.</p> <p>Methods</p> <p>Longitudinal studies in English language which reported the onset of smoking on depression in non clinical populations (age 13-19) published between January 1990 and July 2008 were selected from PubMed, OVID, and PsychInfo databases. Study characteristics were extracted. Meta-analytic pooling procedures with random effects were used.</p> <p>Results</p> <p>Fifteen studies were retained for analysis. The pooled estimate for smoking predicting depression in 6 studies was 1.73 (95% CI: 1.32, 2.40; p < 0.001). The pooled estimate for depression predicting smoking in 12 studies was 1.41 (95% CI: 1.21, 1.63; p < 0.001). Studies that used clinical measures of depression were more likely to report a bidirectional effect, with a stronger effect of depression predicting smoking.</p> <p>Conclusion</p> <p>Evidence from longitudinal studies suggests that the association between smoking and depression is bidirectional. To better estimate these effects, future research should consider the potential utility of: (a) shorter intervals between surveys with longer follow-up time, (b) more accurate measurement of depression, and (c) adequate control of confounding.</p

Nucleolus: the fascinating nuclear body

Nucleoli are the prominent contrasted structures of the cell nucleus. In the nucleolus, ribosomal RNAs are synthesized, processed and assembled with ribosomal proteins. RNA polymerase I synthesizes the ribosomal RNAs and this activity is cell cycle regulated. The nucleolus reveals the functional organization of the nucleus in which the compartmentation of the different steps of ribosome biogenesis is observed whereas the nucleolar machineries are in permanent exchange with the nucleoplasm and other nuclear bodies. After mitosis, nucleolar assembly is a time and space regulated process controlled by the cell cycle. In addition, by generating a large volume in the nucleus with apparently no RNA polymerase II activity, the nucleolus creates a domain of retention/sequestration of molecules normally active outside the nucleolus. Viruses interact with the nucleolus and recruit nucleolar proteins to facilitate virus replication. The nucleolus is also a sensor of stress due to the redistribution of the ribosomal proteins in the nucleoplasm by nucleolus disruption. The nucleolus plays several crucial functions in the nucleus: in addition to its function as ribosome factory of the cells it is a multifunctional nuclear domain, and nucleolar activity is linked with several pathologies. Perspectives on the evolution of this research area are proposed