Laser ion acceleration using a solid target coupled with a low density layer

We investigate by particle-in-cell simulations in two and three dimensions the laser-plasma interaction and the proton acceleration in multilayer targets where a low density "near-critical" layer of a few micron thickness is added on the illuminated side of a thin, high density layer. This target design can be obtained by depositing a "foam" layer on a thin metallic foil. The presence of the near-critical plasma strongly increases both the conversion efficiency and the energy of electrons and leads to enhanced acceleration of proton from a rear side layer via the Target Normal Sheath Acceleration mechanism. The electrons of the foam are strongly accelerated in the forward direction and propagate on the rear side of the target building up a high electric field with a relatively flat longitudinal profile. In these conditions the maximum proton energy is up to three times higher than in the case of the bare solid target.Comment: 9 pages, 11 figures. Submitted to Physical Review

Coefficient of thermal expansion of nanostructured tungsten based coatings assessed by thermally induced substrate curvature method

The in plane coefficient of thermal expansion (CTE) and the residual stress of nanostructured W based coatings are extensively investigated. The CTE and the residual stresses are derived by means of an optimized ad-hoc developed experimental setup based on the detection of the substrate curvature by a laser system. The nanostructured coatings are deposited by Pulsed Laser Deposition. Thanks to its versatility, nanocrystalline W metallic coatings, ultra-nano-crystalline pure W and W-Tantalum coatings and amorphous-like W coatings are obtained. The correlation between the nanostructure, the residual stress and the CTE of the coatings are thus elucidated. We find that all the samples show a compressive state of stress that decreases as the structure goes from columnar nanocrystalline to amorphous-like. The CTE of all the coatings is higher than the one of the corresponding bulk W form. In particular, as the grain size shrinks, the CTE increases from 5.1 10$^{-6}$ K$^{-1}$ for nanocrystalline W to 6.6 10$^{-6}$ K$^{-1}$ in the ultra-nano-crystalline region. When dealing with amorphous W, the further increase of the CTE is attributed to a higher porosity degree of the samples. The CTE trend is also investigated as function of materials stiffness. In this case, as W coatings become softer, the easier they thermally expand.Comment: The research leading to these results has also received funding from the European Research Council Consolidator Grant ENSURE (ERC-2014-CoG No. 647554

Laser cleaning of diagnostic mirrors from tungsten-oxygen tokamak-like contaminants

This paper presents a laboratory-scale experimental investigation about the laser cleaning of diagnostic first mirrors from tokamak-like contaminants, made of oxidized tungsten compounds with different properties and morphology. The re-deposition of contaminants sputtered from a tokamak first wall onto first mirrors' surfaces could dramatically decrease their reflectivity in an unacceptable way for the proper functioning of plasma diagnostic systems. The laser cleaning technique has been proposed as a solution to tackle this issue. In this work, pulsed laser deposition was exploited to produce rhodium films functional as first mirrors and to deposit onto them contaminants designed to be realistic in reproducing materials expected to be re-deposited on first mirrors in a tokamak environment. The same laser system was also used to perform laser cleaning experiments, exploiting a sample handling procedure that allows one to clean some cm2 in a few minutes. Cleaning effectiveness was evaluated in terms of specular reflectance recovery and mirror surface integrity. The effect of different laser wavelengths (λ= 1064, 266 nm) on the cleaning process was also addressed, as well as the impact of multiple contamination/cleaning cycles on the process outcome. A satisfactory recovery of pristine mirror reflectance (≥90%) was obtained in the vis-NIR spectral range, avoiding at the same time mirror damaging. The results here presented show the potential of the laser cleaning technique as an attractive solution for the cleaning of diagnostic first mirrors

Numerical investigation of non-linear inverse Compton scattering in double-layer targets

Non-linear inverse Compton scattering (NICS) is of significance in laser-plasma physics and for application-relevant laser-driven photon sources. Given this interest, we investigated this synchrotron-like photon emission in a promising configuration achieved when an ultra-intense laser pulse interacts with a double-layer target (DLT). Numerical simulations with two-dimensional particle-in-cell codes and analytical estimates are used for this purpose. The properties of NICS are shown to be governed by the processes characterizing laser interaction with the near-critical and solid layers composing the DLT. In particular, electron acceleration, laser focusing in the low-density layer, and pulse reflection on the solid layer determine the radiated power, the emitted spectrum, and the angular properties of emitted photons. Analytical estimates, supported by simulations, show that quantum effects are relevant at laser intensities as small as similar to 1 0 21 W/cm(2) Target and laser parameters affect the NICS competition with bremsstrahlung and the conversion efficiency and average energy of emitted photons. Therefore, DLT properties could be exploited to tune and enhance photon emission in experiments and future applications

Laser-driven production with advanced targets of Copper-64 for medical applications

Radionuclides are of paramount importance in nuclear medicine both for clinical uses and radiopharmaceutical production. Among the others, nuclides suitable for theranostics like Copper-64 are particularly attractive since they can play both a diagnostic and therapeutic role. In the last years, the growing demand for these nuclides stimulated the research of new solutions, along with cyclotrons already in use, for their production. In this respect, a promising alternative is laser-driven proton accelerators based on the interaction of superintense laser pulses with target materials. Because of their potential compactness and flexibility, they are under investigation for several applications ranging from materials science to nuclear medicine. Moreover, the use of advanced Double-Layer targets (DLTs) was identified as a viable route to increase the number and energy of the accelerated protons to satisfy the requirements of demanding applications. In this contribution, we numerically investigate the use of DLT-based laser-driven sources for Copper-64 production. We show that activities relevant to pre-clinical studies can be achieved with an existing 150 TW laser and DLTs. Moreover, we extend the discussion by considering a broad range of laser systems by exploiting a theoretical model. Our results can guide the choice of laser and target parameters for future experimental investigations

Ultra-intense laser interaction with nanostructured near-critical plasmas

Near-critical plasmas irradiated at ultra-high laser intensities (I > 1018W/cm2) allow to improve the performances of laser-driven particle and radiation sources and to explore scenarios of great astrophysical interest. Near-critical plasmas with controlled properties can be obtained with nanostructured low-density materials. By means of 3D Particle-In-Cell simulations, we investigate how realistic nanostructures influence the interaction of an ultra-intense laser with a plasma having a near-critical average electron density. We find that the presence of a nanostructure strongly reduces the effect of pulse polarization and enhances the energy absorbed by the ion population, while generally leading to a significant decrease of the electron temperature with respect to a homogeneous near-critical plasma. We also observe an effect of the nanostructure morphology. These results are relevant both for a fundamental understanding and for the foreseen applications of laser-plasma interaction in the near-critical regime

Laser cleaning of diagnostic mirrors from tokamak-like carbon contaminants

This paper presents a laboratory-scale experimental investigation of laser cleaning of diagnostic First Mirrors (FMs). Redeposition of contaminants sputtered from tokamak first wall onto FMs surface could dramatically decrease their reflectivity in an unacceptable way for the functioning of the plasma diagnostic systems. Laser cleaning is a promising solution to tackle this issue. In this work, pulsed laser deposition was exploited to produce rhodium films functional as FMs and to deposit onto them carbon contaminants with tailored features, resembling those found in tokamaks. The same laser system was also used to perform laser cleaning experiments by means of a sample handling procedure that allows to clean some cm(2) in few minutes. The cleaning effectiveness was evaluated in terms of specular reflectivity recovery and mirror surface integrity. The effect of different laser wavelengths (lambda = 1064, 266 nm) on the cleaning process is also addressed

Verbano

L’obiettivo del progetto è la soluzione del problema Verbano tramite la scelta di una nuova regolazione e di oppurtuni interventi strutturali. Tale soluzione deve tendere a minimizzare i danni causati da eventi alluvionali tanto a monte quanto a valle, i danni indotti dalla mancata fornitura idrica agli utenti irrigui ed idroelettrici di valle e quelli subiti dalla navigazione e dal turismo quando si deprimono eccessivamente i livelli lacuali, senza trascurare, nel contempo, il mantenimento di un deflusso minimo nel Ticino, a valle dello sbarramento del Panperduto. In tale ricerca si dovranno ovviamente tener conto dei vincoli posti dalla capacità di smaltimento delle portate all’incile del lago e dalla necessità di mantenere attiva la sua naturale funzione di laminazione in occasione di eventi alluvionali che interessino anche il Po

Fabrication and Characterization of Molybdenum Tips for Scanning Tunneling Microscopy and Spectroscopy

We present a method for the preparation of bulk molybdenum tips for scanning Tunneling Microscopy and Spectroscopy (STM - STS) and we assess their potential in performing high resolution imaging and local spectroscop by measurements on different single crystal surfaces in UHV, namely Au(111), Si(111)-7x7 and titanium oxide 2D ordered nanostructures supported on Au(111). The fabrication method is versatile and can be extended to other metals, e.g. cobalt