The effect of age, sex and a firm-textured surface on postural control.

In previous studies, the influence of plantar sensation has been examined using various textured surfaces with different stiffness materials to assess static balance. This study investigated the effects of a Firm Textured Surface (FTS) along with age and sex-related influences on postural control under different visual conditions. Forty subjects (20 elderly, 10 males, mean age 68.30, 10 females, mean age 68.00, and 20 young people, 10 males, mean age 25.45, 10 females, mean age 27.30) participated in this study maintained a quiet standing on FTS, foam and firm surfaces with eyes open and closed. The center of pressure displacement (CoPDISP), CoP velocity (CoPVEL), and sway velocity of the CoP in anteroposterior (AP) and mediolateral (ML) direction (VA/P and VM/L) were measured. FTS was associated with lower postural sway measures in both the groups with eyes open and closed. However, the foam surface showed the worst results in all postural parameters under all experimental conditions. Separate four-way ANOVAs were applied to each dependent variable. The main effects of surface (p < 0.0001), vision (p < 0.0001) and age (p < 0.0001 for CoPDISP, CoPVEL and VA/P; p = 0.0003 for VM/L) were significant in each of the four fitted models. Sex was never significant, either as a main effect or an interaction with other experimental factors. Eyes open were able to reduce the negative effects of the foam surfaces but without vision the proprioceptive sensory system cues of the body state become more important for maintaining balance. A good stimulation with rigid texture should be considered as relief to reduce the physiological-related decline of afferent information with ag

Acoustic coupling in capacitive microfabricated ultrasonic transducers: modeling and experiments

In the design of low-frequency transducer arrays for active sonar systems, the acoustic interactions that occur between the transducer elements have received much attention. Because of these interactions, the acoustic loading on each transducer depends on its position in the array, and the radiated acoustic power may vary considerably from one element to another. Capacitive microfabricated ultrasonic transducers (CMUT) are made of a two-dimensional array of metallized micromembranes, all electrically connected in parallel, arid driven into flexural motion by the electrostatic force produced by an applied voltage. The mechanical impedance of these membranes is typically much lower than the acoustic impedance of water. In our investigations of acoustic coupling in CMUTs, interaction effects between the membranes in immersion were observed, similar to those reported in sonar arrays. Because CMUTs have many promising applications in the field of medical ultrasound imaging, understanding of cross-coupling mechanisms and acoustic interaction effects is especially important for reducing cross-talk between array elements, which can produce artifacts and degrade image quality. In this paper, we report a finite-element study of acoustic interactions in CMUTs and experimental results obtained by laser interferometry measurements. The good agreement found between finite element modeling (FEM) results and optical displacement measurements demonstrates that acoustic interactions through the liquid represent a major source of cross coupling in CMUTs

An Accurate Model for Capacitive Micromachined Ultrasonic Transducers

Modeling of capacitive micromachined ultrasonic transducers (cMUTs) is based on a two-port network with an electrical and a mechanical side. To obtain a distributed model, a solution of the differential equation of motion of the diaphragm for each element of the transducer has to be found. Previous works omit the mechanical load of the cavity behind the diaphragm, i.e., the effect of the gas inside. In this paper, we propose a distributed model for cMUTs that takes this effect into account. A closed-form solution of the mechanical impedance of the membranes has been obtained, including the effect of the restoring forces because of the stiffness of the membrane and because of the compression of the air in the cavity. Simulation results based on the presented model are compared with the experimental data for two types of cMUTs reported in the recent literature. It is demonstrated that the compression of the air has a significant effect on the fundamental frequency of the air transducer, with a deviation of about 22% from the prediction of a model that does not consider the interaction between the vibrating diaphragm and the air cushion

An accurate model for capacitive micromachined ultrasonic transducers

Modeling of capacitive micromachined ultrasonic transducers (cMUTs) is based on a two-port network with an electrical and a mechanical side. To obtain a distributed model, a solution of the differential equation of motion of the diaphragm for each element of the transducer has to be found. Previous works omit the mechanical load of the cavity behind the diaphragm, i.e., the effect of the gas inside. In this paper, we propose a distributed model for cMUTs that takes this effect into account. A closed-form solution of the mechanical impedance of the membranes has been obtained, including the effect of the restoring forces because of the stiffness of the membrane and because of the compression of the air in the cavity. Simulation results based on the presented model are compared with the experimental data for two types of cMUTs reported in the recent literature. It is demonstrated that the compression of the air has a significant effect on the fundamental frequency of the air transducer, with a deviation of about 22% from the prediction of a model that does not consider the interaction between the vibrating diaphragm and the air cushion

A power transducer system for the ultrasonic lubrication of the continuous steel casting

A critical point in the continuous steel casting process exists in the meniscus zone of the cooled mould, i.e., the region in which the steel stream flowing out of the tundish nozzle starts to solidify. This is a critical point because of the sticking that occurs between the solid shell of steel and the mould. In this work, a new system for the ultrasonic lubrication of the continuous steel casting is proposed and experimentally tested. The basic idea is to excite one of the mould’s natural vibration modes by means of a distributed ultrasonic source. This source is composed of an array of power emitters, with each of them placed upon an antinode of the mould. An experimental characterization of the vibrational behavior of a square mould was first carried out. The most active resonance modes of the mould were detected with an experimental technique based on a simple impedance measurement. The modal shape of the selected mode, and hence the position of antinodes, was obtained by means of interferometer measurements. Additional experimental investigations were performed by exciting mould vibrations with up to four piezoceramic disks placed on different sets of antinodes. Some positioning criteria to maximize the superposition effect were derived. Measurements were obtained through excitation of the mould with up to four Langevin-type power emitters, designed and manufactured to work at the mould’s selected resonance frequency. These measurements have shown that, by increasing the number of emitters, the ultrasonic power transmitted to the mould and, consequently, the maximum available displacement, increases. Other practical advantages of the proposed system are highlighted and discussed

The effects of membrane metallization in capacitive microfabricated ultrasonic transducers

The mechanical effects of the metal layer on the membranes of capacitive micromachined ultrasonic transducers (CMUTs) are analyzed in this paper by means of finite element simulations. The influence of electrode size and thickness on the electrostatic behavior of the single CMUT cell, including diaphragm displacement, cell capacitance, and collapse voltage, is explored. The effect on device sensitivity is investigated through the transformation factor of the cell, that is computed by FEM and compared with the parallel plate model prediction. It is found that for a non-negligible electrode thickness, as in the majority of fabricated devices, both the static and dynamic performance of the cell can be affected in a significant way. Thus, the effects of membrane metallization must be taken into account in CMUT design and optimization

Acoustic Coupling in Capacitive Microfabricated Ultrasonic Transducers: Modeling and Experiments

In the design of low-frequency transducer arrays for active sonar systems, the acoustic interactions that occur between the transducer elements have received much attention. Because of these interactions, the acoustic loading on each transducer depends on its position in the array, and the radiated acoustic power may vary considerably from one element to another. Capacitive microfabricated ultrasonic transducers (CMUT) are made of a two-dimensional array of metallized micromembranes, all electrically connected in parallel, and driven into flexural motion by the electrostatic force produced by an applied voltage. The mechanical impedance of these membranes is typically much lower than the acoustic impedance of water. In our investigations of acoustic coupling in CMUTs, interaction effects between the membranes in immersion were observed, similar to those reported in sonar arrays. Because CMUTs have many promising applications in the field of medical ultrasound imaging, understanding of cross-coupling mechanisms and acoustic interaction effects is especially important for reducing cross-talk between array elements, which can produce artifacts and degrade image quality. In this paper, we report a finite-element study of acoustic interactions in CMUTs and experimental results obtained by laser interferometry measurements. The good agreement found between finite element modeling (FEM) results and optical displacement measurements demonstrates that acoustic interactions through the liquid represent a major source of cross coupling in CMUTs