The influence of air and liquid properties on airblast atomization

This thesis reports the results of a detailed programme of research on airblast atomization carried out using a specially designed atomizer in which the liquid is first spread into a thin sheet and then exposed on both sides to high velocity air. The primary aim of the investigation was to examine the influence of air and liquid properties on atomization quality. The work was divided into four main phases:- (1) The first phase was confined to the effects of liquid properties, namely viscosity, surface tension and density on mean drop size. Special liquids were produced to study the separate effect of each property on atomization quality. They presented a range of values of viscosity from 1.0 to 124 centipoise, while surface tension and density were varied between 26 and 73.5 dynes/cm and 0.8 and 1.8 gm/cm3 respectively. Atomizing air velocities covered the range of practical interest to the designers of continuous combustion systems and varied between 60 and 125 m/sec.(2) To obtain experimental data on the influence of air properties, notably air density, on mean drop size, the air temperature was varied between 23 and 151°C at atmospheric pressure in one series of experiments, while a separate study on the effect of air pressure on atomization quality was undertaken, where tests were conducted at constant levels of air velocity and temperature, using a range of liquid flows from 5 to 30 gm/sec, at various levels of air pressure between 1 and 8.5 atm. (3) In order to provide a comprehensive picture of airb1ast atomizer performance over a wide range of conditions the separate effects of varying air velocity, liquid flow rate, and hence atomizing air/liquid mass ratio on SMD were examined. This study enabled a better understanding of the effects of changes in operation on the atomizer's performance. (4) In all three phases above, velotities of both inner and outer atomizing air streams were kept equal. This last phase was aimed at studying the effect of varying the velocity between the inner and outer air streams. Best atomization quality was achieved when 65% of the total atomizing air was flowing through the outer stream. A detailed description of the light-scattering technique for drop size measurement is included. A discussion on the importance of the results obtained and their direct relevance to the design of airblast atomizers is given. A dimensional analysis and inspection of all the data obtained on the effects of air and liquid properties on atomization quality showed that over the following range of conditions: Liquid viscosity 1.0 to 44 centipoise Liquid surface tension 26 to 73.5 dynes/cm Liquid density 0.78 to 1.5 gm/cm³ Air velocity 70 to 125 m/sec Air temperature 20 to 151 °c Air pressure 1.0 to 8.5 kgf/cm² . Air/liquid ratio 2 to 6 Cont.........

The influence of air and liquid properties on airblast atomization

This thesis reports the results of a detailed programme of research on airblast atomization carried out using a specially designed atomizer in which the liquid is first spread into a thin sheet and then exposed on both sides to high velocity air. The primary aim of the investigation was to examine the influence of air and liquid properties on atomization quality. The work was divided into four main phases:- (1) The first phase was confined to the effects of liquid properties, namely viscosity, surface tension and density on mean drop size. Special liquids were produced to study the separate effect of each property on atomization quality. They presented a range of values of viscosity from 1.0 to 124 centipoise, while surface tension and density were varied between 26 and 73.5 dynes/cm and 0.8 and 1.8 gm/cm3 respectively. Atomizing air velocities covered the range of practical interest to the designers of continuous combustion systems and varied between 60 and 125 m/sec.(2) To obtain experimental data on the influence of air properties, notably air density, on mean drop size, the air temperature was varied between 23 and 151°C at atmospheric pressure in one series of experiments, while a separate study on the effect of air pressure on atomization quality was undertaken, where tests were conducted at constant levels of air velocity and temperature, using a range of liquid flows from 5 to 30 gm/sec, at various levels of air pressure between 1 and 8.5 atm. (3) In order to provide a comprehensive picture of airb1ast atomizer performance over a wide range of conditions the separate effects of varying air velocity, liquid flow rate, and hence atomizing air/liquid mass ratio on SMD were examined. This study enabled a better understanding of the effects of changes in operation on the atomizer's performance. (4) In all three phases above, velotities of both inner and outer atomizing air streams were kept equal. This last phase was aimed at studying the effect of varying the velocity between the inner and outer air streams. Best atomization quality was achieved when 65% of the total atomizing air was flowing through the outer stream. A detailed description of the light-scattering technique for drop size measurement is included. A discussion on the importance of the results obtained and their direct relevance to the design of airblast atomizers is given. A dimensional analysis and inspection of all the data obtained on the effects of air and liquid properties on atomization quality showed that over the following range of conditions: Liquid viscosity 1.0 to 44 centipoise Liquid surface tension 26 to 73.5 dynes/cm Liquid density 0.78 to 1.5 gm/cm³ Air velocity 70 to 125 m/sec Air temperature 20 to 151 °c Air pressure 1.0 to 8.5 kgf/cm² . Air/liquid ratio 2 to 6 Cont.........

NANOTECHNOLOGY BASED GAS SENSING DEVICES

poster abstractGas sensors have a wide range of applications, and many of these applications require very high sensitivity. Types of gas sensors include electrochemical, chemiresistor, infrared point, infrared imaging, semiconductors, ultrasonic and holographic sensors. Nanotechnology is a branch of engineering and science that deals with materials, processes, and devices at nanoscale, one billionth of a meter. Using nanotechnology highly sensitive sensors can be produced. This poster will present chemiresistor sensors developed using nanotechnology at Integrated Nanosystems Development Institute (INDI). Poly (vinylidene fluoride-co-hexafluoropropene) (PVDF-HFP), Carbon black, and carbon nanotube materials were used. Sensors were fabricated using photolithography and spin-coating or spraying methods. The sensors were then tested with acetone, ethanol, water vapor, and other gasses using a sensor testing setup and a data logger system. The poster will present fabrication methods and experimental results. Mentor: Maher Rizkalla, and Sudir Shrestha, Department of Electrical and Computer Engineering, Purdue School of Engineering and Technology, IUPUI

Stomatin-like Protein 2 Links Mitochondria to T-Cell Receptor Signalosomes at the Immunological Synapse and Enhances T-Cell Activation

T cell activation through the antigen receptor (TCR) requires sustained signalling from microclusters in the peripheral region of the immunological synapse (IS). The bioenergetics of such prolonged signaling have been linked to the redistribution of mitochondria to the IS. Here, we report that stomatin-like protein-2 (SLP-2) plays an important role in this process by bridging polarized mitochondria to these signaling TCR microclusters or signalosomes in the IS in a polymerized actin-dependent manner. In this way, SLP-2 helps to sustain TCR-dependent signalling and enhances T cell activation

Identification and assessment of geohazards affecting pipelines and urban areas

The paper addresses methods and criteria of risk assessment associated with land subsidence threatening pipelines, buildings, and constructions. Currently, there are some practical issues relating to geohazards that should be taken into account while constructing a pipeline. The article provides comparison data on the effects of Spitak earthquake and the natural disaster in Neftegorsk in terms of geohazards impact on the pipeline systems. The suggested risk assessment procedure embraces a wide range of aspects: from soil properties to economic and management issues

Quality Improvement in Liver Transplant Anesthesia: Early Extubation in the Operating Room

Presented as a poster at Indiana Society of Anesthesiologists Annual Meeting 2021

Glycemic index, glycemic load and glycemic response: An International Scientific Consensus Summit from the International Carbohydrate Quality Consortium (ICQC)

Abstract Background and aims The positive and negative health effects of dietary carbohydrates are of interest to both researchers and consumers. Methods International experts on carbohydrate research held a scientific summit in Stresa, Italy, in June 2013 to discuss controversies surrounding the utility of the glycemic index (GI), glycemic load (GL) and glycemic response (GR). Results The outcome was a scientific consensus statement which recognized the importance of postprandial glycemia in overall health, and the GI as a valid and reproducible method of classifying carbohydrate foods for this purpose. There was consensus that diets low in GI and GL were relevant to the prevention and management of diabetes and coronary heart disease, and probably obesity. Moderate to weak associations were observed for selected cancers. The group affirmed that diets low in GI and GL should always be considered in the context of diets otherwise understood as healthy, complementing additional ways of characterizing carbohydrate foods, such as fiber and whole grain content. Diets of low GI and GL were considered particularly important in individuals with insulin resistance. Conclusions Given the high prevalence of diabetes and pre-diabetes worldwide and the consistency of the scientific evidence reviewed, the expert panel confirmed an urgent need to communicate information on GI and GL to the general public and health professionals, through channels such as national dietary guidelines, food composition tables and food labels

The role of bone sialoprotein in the tendon-bone insertion

© 2016 International Society of Matrix Biology. Tendons/ligaments insert into bone via a transitional structure, the enthesis, which is susceptible to injury and difficult to repair. Fibrocartilaginous entheses contain fibrocartilage in their transitional zone, part of which is mineralized. Mineral-associated proteins within this zone have not been adequately characterized. Members of the Small Integrin Binding Ligand N-linked Glycoprotein (SIBLING) family are acidic phosphoproteins expressed in mineralized tissues. Here we show that two SIBLING proteins, bone sialoprotein (BSP) and osteopontin (OPN), are present in the mouse enthesis. Histological analyses indicate that the calcified zone of the quadriceps tendon enthesis is longer in Bsp-/- mice, however no difference is apparent in the supraspinatus tendon enthesis. In an analysis of mineral content within the calcified zone, micro-CT and Raman spectroscopy reveal that the mineral content in the calcified fibrocartilage of the quadriceps tendon enthesis are similar between wild type and Bsp-/- mice. Mechanical testing of the patellar tendon shows that while the tendons fail under similar loads, the Bsp-/- patellar tendon is 7.5% larger in cross sectional area than wild type tendons, resulting in a 16.5% reduction in failure stress. However, Picrosirius Red staining shows no difference in collagen organization. Data collected here indicate that BSP is present in the calcified fibrocartilage of murine entheses and suggest that BSP plays a regulatory role in this structure, influencing the growth of the calcified fibrocartilage in addition to the weakening of the tendon mechanical properties. Based on the phenotype of the Bsp-/- mouse enthesis, and the known in vitro functional properties of the protein, BSP may be a useful therapeutic molecule in the reattachment of tendons and ligaments to bone