1,280 research outputs found
Efficient implicit simulation for incremental forming
Single Point Incremental Forming (SPIF) is a displacement controlled process performed on a CNC machine. A clamped blank is deformed by the movement of a small sized tool that follows a prescribed tool path. An extensive overview of the process has been given in [1]. The tool size plays a crucial role in the SPIF process. The small radius of the forming tool concentrates the strain at the zone of deformation in the sheet under the forming tool. The tool has to travel a lengthy forming path all over the blank to introduce the deformation. Numerically, this requires performing thousands of load increments on a relatively fine FE model resulting in enormous computing time. A typical computing time for implicit simulation of a small academic test is measured in by days. The focus of this paper is to efficiently use the implicit time integration method in order to reduce the required computing time for incremental forming implicit simulation drastically
Stable incremental deformation of a strip to high strain
This paper presents the effect of combined stretching and bending on the achieved strain in\ud
incremental sheet forming ISF. A simple two dimensional model of strip undergoing stretching and\ud
travelling three point bending in cyclic form is used. The numerical model presents the effect of the\ud
ratio of stretching velocity to roll-set speed on the achieved strain and its distributio
Thermo-mechanical Forming of Al–Mg–Si Alloys: Modeling and Experiments
In an ongoing quest to realize lighter vehicles with improved fuel efficiency, deformation characteristics of the material AA 6016 is investigated. In the first part of this study, material behavior of Al–Mg–Si sheet alloy is investigated under different process (temperature and strain rate) and loading (uniaxial and biaxial) conditions experimentally. Later, warm cylindrical cup deep drawing experiments were performed to study the effect of various parameters on warm forming processes, such as the effect of punch velocity, holding time, temper and temperature on force-displacement response. The plastic anisotropy of the material which can be directly reflected by the earing behavior of the drawn cups has also been studied. Finite element simulations can be a powerful tool for the design of warm forming processes and tooling. Their accuracy will depend on the availability of material models that are capable of describing the influence of temperature and strain rate on the flow stresses. The physically based Nes model is used to describe the influence of temperature and strain rate and the Vegter yield criterion is used to describe the plastic anisotropy of the sheet. Experimental drawing test data are used to validate the modeling approaches
Causes of pediatric mortality and case-fatality rates in eight Médecins Sans Frontières-supported hospitals in Africa
Wrinkling prediction with adaptive mesh refinement
An adaptive mesh refinement procedure for wrinkling prediction analyses is presented. First the\ud
critical values are determined using Hutchinson’s bifurcation functional. A wrinkling risk factor is then\ud
defined and used to determined areas of potential wrinkling risk. Finally, a mesh refinement is operate
On adaptive mesh refinement in wrinkling prediction analysis
Hutchinson approach has been successfully used by a number of researchers in thin sheet metal forming processes for wrinkling prediction. However, Hutchinson approach is limited to regions of the sheet that are free of any contact. Therefore, a new wrinkling indicator that can be used in the contact areas is proposed. Discretisation error indicators are also used to present a comprehensive approach to wrinkling prediction analysis
Effect of temperature on anisotropy in forming simulations of aluminum alloys
A combined experimental and numerical study of the effect of temperature on anisotropy in warm forming of AA 6016-T4 aluminum was performed. The anisotropy coefficients of the Vegter yield function were calculated from crystal plasticity models with an adequate combination of extra slip systems. Curve fitting was used to fit the anisotropy coefficients calculated at discrete temperatures. This temperature dependent constitutive model was successfully applied to the coupled thermo-mechanical analysis of deep drawing of aluminum sheet and results were compared with experiments
Metal contacts to lowly doped Si and ultra thin SOI
We present our investigations on the fabrication of ohmic and Schottky contacts of several metals on lowly doped bulk Si and SOI wafers. Through this paper we evaluate the fabrication of rectifying devices in which no doping is intentionally introduced
Modelling of Dynamic Strain Aging with a Dislocation-Based Isotropic Hardening Model and Investigation of Orthogonal Loading
Based on experimental results, a dislocation material model describing the dynamic strain aging\ud
effect at different temperatures is presented. One and two stage loading tests were performed in\ud
order to investigate the influence of the loading direction as well as the temperature influence due\ud
to the hardening mechanism. Bergström’s theory of work hardening was used as a basis for the\ud
model development regarding the thermal isotropic behavior as well as the Chaboche model to\ud
describe the kinematic hardening. Both models were implemented in an in-house FE-Code in\ud
order to simulate the real processes. The present paper discusses two hardening mechanisms,\ud
where the first part deals with the pure isotropic hardening including dynamic strain aging and the\ud
second part involves the influence of the loading direction regarding combined (isotropic and\ud
kinematic) hardening behavior
- …