The maximum theoretical performance of unconcentrated solar photovoltaic and thermoelectric generator systems

The maximum efficiency for photovoltaic (PV) and thermoelectric generator (TEG) systems without concentration is investigated. Both a combined system where the TEG is mounted directly on the back of the PV and a tandem system where the incoming sunlight is split, and the short wavelength radiation is sent to the PV and the long wavelength to the TEG, are considered. An analytical model based on the Shockley-Queisser efficiency limit for PVs and the TEG figure of merit parameter $zT$ is presented. It is shown that for non-concentrated sunlight, even if the TEG operates at the Carnot efficiency and the PV performance is assumed independent of temperature, the maximum increase in efficiency is 4.5 percentage points (pp.) for the combined case and 1.8 pp. for the tandem case compared to a stand alone PV. For a more realistic case with a temperature dependent PV and a realistic TEG, the gain in performance is much lower. For the combined PV and TEG system it is shown that a minimum $zT$ value is needed in order for the system to be more efficient than a stand alone PV system.Comment: 6 pages, 5 figure

Computed tomographic imaging characteristics of the normal canine lacrimal glands.

BackgroundThe canine lacrimal gland (LG) and accessory lacrimal gland of the third eyelid (TEG) are responsible for production of the aqueous portion of the precorneal tear film. Immune-mediated, toxic, neoplastic, or infectious processes can affect the glands directly or can involve adjacent tissues, with secondary gland involvement. Disease affecting these glands can cause keratoconjunctivitis sicca, corneal ulcers, and loss of vision. Due to their location in the orbit, these small structures are difficult to evaluate and measure, making cross-sectional imaging an important diagnostic tool. The detailed cross-sectional imaging appearance of the LG and TEG in dogs using computed tomography (CT) has not been reported to date.ResultsForty-two dogs were imaged, and the length, width, and height were measured and the volume calculated for the LGs & TEGs. The glands were best visualized in contrast-enhanced CT images. The mean volume of the LG was 0.14 cm3 and the TEG was 0.1 cm3. The mean height, width, and length of the LG were, 9.36 mm, 4.29 mm, and 9.35 mm, respectively; the corresponding values for the TEG was 2.02 mm, 9.34 mm, and 7.90 mm. LG and TEG volume were positively correlated with body weight (p < 0.05).ConclusionsContrast-enhanced CT is a valuable tool for noninvasive assessment of canine lacrimal glands

Processing peracetic acid treated bloodmeal into bioplastic

Renewable and biodegradable bioplastics can be produced from biopolymers such as proteins. Animal blood is a by-product from meat processing and is rich in protein. It is dried into low value bloodmeal and is used as animal feed or fertiliser. Previous work has shown that bloodmeal can be converted into a thermoplastic using water, urea, sodium dodecyl sulphate (SDS), sodium sulphite and triethylene glycol (TEG). To increase its range of applications and acceptance from consumers, the colour and odour was removed from bloodmeal using peracetic acid (PAA). The aim of this study was to investigate the bioplastic processing of 3-5% (w/w) PAA treated bloodmeal. 3-5% PAA treated bloodmeal powder was compression moulded using different combinations of water, TEG, glycerol, SDS, sodium sulphite, urea, borax, salt and sodium silicate at concentrations up to 60 parts per hundred bloodmeal (pphBM). Partially consolidated extrudates and fully consolidated compression moulded sheets were obtained using a combination of water, TEG and SDS. 4% PAA treated bloodmeal produced the best compression moulded sheets and extrudates and was chosen for investigating the effects of water, TEG and SDS concentration on consolidation, specific mechanical energy input (SME) and product colour during extrusion. Analysis of variance (ANOVA) showed SDS was the most important factor influencing its ability to be extruded because it detangled protein chains and allowed them to form new stabilising interactions required for consolidation. The best extruded sample, which was 98% consolidated and 49% white, contained 40 pphBM water, 10 pphBM TEG and 6 pphBM SDS

Evacuated glazing with tempered glass

The application of tempered glass has made it possible to significantly reduce the support pillar number within evacuated glazing (EG) since tempered glass (T-glass) is four to ten times mechanically stronger than annealed glass (A-glass). The thermal transmittance (U-value) of 0.4 m by 0.4 m double evacuated glazing (DEG) with 4 mm thick T-glass and A-glass panes with emittance of 0.03 were determined to be 0.3 Wm−2K−1 and 0.57 Wm−2K−1, respectively (47.4% improvement) using previously experimentally validated finite volume model. The thermal transmittance (U-value) of 0.4 m by 0.4 m triple evacuated glazing (TEG) with 4 mm thick T-glass and A-glass panes with emittance of 0.03 were determined to be 0.11 Wm−2K−1 and 0.28 Wm−2K−1, respectively (60.7% improvement). The improvement in the U-value of EG with T-glass is due to a reduction in support pillar number, leading to reduction in heat conduction through pillar array. The impact of tempered glass on the thermal transmittance for TEG is greater than that of DEG since radiative heat transfer in TEG is much lower than that in DEG, thus the reduction in heat conduction resulted from the reduction of support pillar number in TEG is much larger than that in DE

The performance of a combined solar photovoltaic (PV) and thermoelectric generator (TEG) system

The performance of a combined solar photovoltaic (PV) and thermoelectric generator (TEG) system is examined using an analytical model for four different types of commercial PVs and a commercial bismuth telluride TEG. The TEG is applied directly on the back of the PV, so that the two devices have the same temperature. The PVs considered are crystalline Si (c-Si), amorphous Si (a-Si), copper indium gallium (di)selenide (CIGS) and cadmium telluride (CdTe) cells. The degradation of PV performance with temperature is shown to dominate the increase in power produced by the TEG, due to the low efficiency of the TEG. For c-Si, CIGS and CdTe PV cells the combined system produces a lower power and has a lower efficiency than the PV alone, whereas for an a-Si cell the total system performance may be slightly increased by the TEG.Comment: 10 pages, 6 figure

Improving the efficiency of thermoelectric generators by using solar heat concentrators

In this paper, we propose a method of improving the efficiency of thermoelectric generators (TEGs) by using a lens to concentrate heat on the heat source of a TEG. Initial experiments performed using discrete components show about 60mV increase in the amount of voltage generated when using a magnifying lens. Simulation results on the proposed TEG configuration exhibit up to 16% efficiency when the input heat flux is increased to 500 times that of the sun’s heat flux. The effects of varying the thermoelement length, width, and membrane diameter on the TEG’s performance are also characterized. Lastly, plans to fabricate the device on a SOI wafer in the future are presente

Alternatif Pembangkit Energi Listrik Menggunakan Prinsip Termoelektrik Generator

Thermoelectric generator (TEG) has been used to produce electrical energy, the working principle of TEG, the temperature difference between two materials, will flow current, and produce a potential difference. This principle is known as the "Seebeck effect" which is a reverse phenomenon of the Peltier (Thermoelectric Cooling, TEC) effect. This research was conducted to determine the electrical nergy capacity produced for 10 TEG modules in series. Testing is done by utilizing heat energy from asphalt, water flow and connected to 10 TEG modules. The test results show that the maximum voltage is 18Voltdc 0.49 AmperePembangkit listrik termoelektrik (Thermoelectric Generator, TEG) telah digunakan untuk menghasilkan energi listrik, prinsip kerja TEG, perbedaan temperatur antar dua material, akan mengalirkan arus, dan menghasilkan beda potensial. Prinsip ini dikenal dengan “efek Seebeck” yang merupakan fenomena kebalikan dari efek Peltier (Thermoelectric Cooling, TEC). Penelitian ini dilakukan untuk mengetahui kapasitas energi listrik yang dihasilkanuntuk 10 modul TEG secara seri. Pengujian dilakukan dengan memanfaatkan energi panas dari aspal, aliran air dan terhubung pada 10 modul TEG. Hasil pengujian menunjukkan bahwa tegangan maksimal 18Voltdc 0,49Ampere