The use of acoustics in space exploration

In recent years increased attention has been paid to the potential uses of acoustics forextraterrestrial exploration. The extent to which acoustics per se is used in these studiesvaries greatly. First, there are the cases in which acoustics is simply the medium throughwhich some other time-varying non-acoustic signal (such as the output of a cosmic raydetector) is communicated to humans. Second, perturbations in a non-acoustic signal (e.g.EM) are interpreted through mechanisms relating to acoustic perturbations in the sourcematerial itself. Third, some probes have made direct measurements of acoustic signalswhich have been generated by the probe itself, as is done for example to infer the localatmospheric sound speed from the time-of-flight of an acoustic pulses over a shortdistance (O(10 cm)). Fourth, some studies have discussed ways of interpreting thenatural acoustic signals generated by the extraterrestrial environment itself. The reportdiscusses these cases and the limitations, implications and opportunities forextraterrestrial exploration using acoustics

Thermal pump-compressor for space use Patent

Thermal pump-compressor for converting solar energ

Superconductivity devices: Commercial use of space

A YBCO thick film containing 20 percent Ag2O with a T(sub c) of 86.8 K and J(sub c) of 108 A/sq cm was obtained. The film was fabricated by a two-step firing process, i.e., firing the film at 1000 C for 10 minutes and annealing at 970 C for 30 minutes. The two-step firing process, however, was not suitable for the multiple-lead YBCO sample due to the formation of the 211 green phase at 1000 C in the multiple-lead YBCO sample. A BSCCO thick film printed on a MgO coated MSZ substrate and fired at 845 C for 2 hours exhibited a superconducting behavior at 89 K. Because of its porous microstructure, the critical current density of the BSCCO thick film was limited. This report also includes the results of the YBCO and BSCCO materials used as oxide electrodes for ferroelectric materials. The YBCO electroded PLZT showed higher remanent polarization and coercive field than the sample electroded with silver paste. A higher Curie temperature for the PLZT was obtained from the YBCO electroded sample. The BSCCO electroded sample, however, exhibited the same Curie temperature as that of a silver electroded sample. Dissipation factors of the ferroelectric samples increased when the oxide electrode was applied

Superconductivity devices: Commercial use of space

The high T(sub c) superconducting ceramic materials, developed in 1987, are now being extensively investigated for a variety of engineering applications. These applications include such devices as conducting links, rotating and linear bearings, sensors, filters, switches, high Q cavities, magnets, and motors. Some of these devices take advantage of the material's ability to lose all electrical resistance at a critical temperature, T(sub c), while others make use of the repulsion forces generated between the magnetic field of a permanent magnet and a superconductor which is cooled below its T(sub c), Meissner effect. This report describes the work accomplished to date by: (1) reviewing the present state of the art in actuator technology, (2) evaluating processing and fabrication of high strain electrostrictive materials, and (3) testing these electrostrictive materials

Why Use Sobolev Metrics on the Space of Curves

We study reparametrization invariant Sobolev metrics on spaces of regular curves. We discuss their completeness properties and the resulting usability for applications in shape analysis. In particular, we will argue, that the development of efficient numerical methods for higher order Sobolev type metrics is an extremely desirable goal

Superconductivity devices: Commercial use of space

High T sub C superconducting thick film were prepared by a screen printing process. Y-based (YBa2Cu3O(7-x) superconducting thick film were printed on 211/Al2O3, SNT/Al2O3, and YSZ substrates. Because of poor adhesion of the superconductor thick films to 211/Al2O3 and SNT/Al2O3 substrates, relatively low T sub C and J sub C values were obtained from the films printed on these substrates. Critical temperatures (T sub C) of YBa2Cu3O(7-x) thick films deposited on 211/Al2O3 and SNT/Al2O3 substrates were about 80 K. The critical current densities (J sub C) of these films were less than 2 A/sq cm. Higher T sub C and J sub C YBa2Cu3O(7-x) thick films were printed on YSZ substrates. A YBa2Cu3O(7-x) thick film with T sub C=86.4 and J sub C= 50.4 A/sq cm was prepared by printing the film on YSZ substrate and firing at 990 C for 10 minutes. Multiple-lead samples were also prepared on the YSZ substrates. The multiple-lead samples showed lower T sub C and/or J sub C values than those of the plain samples. The electrical properties of YBa2Cu3O(7-x) thick films were determined by the microstructures of the films. The YBa2Cu3O(7-x) thick films printed on the YSZ substrates, which had the best properties among the films printed on the three different kinds of substrates, had the highest density and the best particle interconnection. The YBa2Cu3O(7-x) thick films with preferred orientation in (001) direction were obtained on the YSZ substrates. Cracks, which retard the properties of the films, were found from the films deposited on the YSZ substrates. Currently, a MSZ (Magnesium Stabilized Zirconia) substrate, which had higher thermal expansion coefficient than the YSZ substrate, is used as substrate for the YBa2Cu3O(7-x) thick film in order to eliminate the cracks on the film. Bi-based superconductor thick films were printed on polycrystalline MgO and YSZ substrates. Interactions between BSCCO thick films and the YSZ substrates were observed. Various buffer layer materials were applied onto the substrates in order to avoid the interactions between the BSCCO thick films and the ZrO2-based substrates. So far, a BSCCO printed on MgO substrate with T Sub C=89K was obtained. The J sub C of the film was lower than 0.1 A/sq cm by reason of poor interconnectivity of the BSCCO particles

Gas density detector for use in space

Gas density detector for meteoroid monitorin

The use of perfluoroether lubricants in unprotected space environments

A series of ball bearing tests in simulated space environment are described which determine durability of perfluoroether lubricants. The results of the examination of the test bearings for each stage are described and experimental techniques designed to overcome lubricant degradation are outlined

Wim Wenders’ Use of Space in The Million Dollar Hotel

Wim Wenders has been quoted as saying, of his own development as a filmmaker, that he is “a painter of space engaged on a quest for time” (qtd. in Graf, 2002, p.63). This paper offers a systematic assessment of the way Wenders creates the filmic space of The Million Dollar Hotel (Wenders, 1999) from a place existing in downtown Los Angeles: the Frontier Hotel on East 5th St., LA (with its companion hotel, the Rosslyn, just across the street). This study considers both place and space as filmic effects, which operate on a continuum from documentary to fantasy

Geometry from Information Geometry

We use the method of maximum entropy to model physical space as a curved statistical manifold. It is then natural to use information geometry to explain the geometry of space. We find that the resultant information metric does not describe the full geometry of space but only its conformal geometry -- the geometry up to local changes of scale. Remarkably, this is precisely what is needed to model "physical" space in general relativity.Comment: Presented at MaxEnt 2015, the 35th International Workshop on Bayesian Inference and Maximum Entropy Methods in Science and Engineering (July 19-24, 2015, Potsdam NY, USA