8-Phase Ring oscillator for modern receivers

The evolution of receiver architectures, built in modern CMOS technologies, allows the design of high efficient receivers. A key block in modern receivers is the oscillator. The main objective of this thesis is to design a very low power and low area 8-Phase Ring Oscillator for biomedical applications (ISM and WMTS bands). Oscillators with multiphase outputs and variable duty cycles are required. In this thesis we are focused in 12.5% and 50% duty-cycles approaches. The proposed circuit uses eight inverters in a ring structure, in order to generate the output duty cycle of 50%. The duty cycle of 1/8 is achieved through the combination of the longer duty cycle signals in pairs, using, for this purpose, NAND gates. Since the general application are not only the wireless communications context, as well as industrial, scientific and medical plans, the 8-Phase Oscillator is simulated to be wideband between 100 MHz and 1 GHz, and be able to operate in the ISM bands (447 MHz-930 MHz) and WMTS (600 MHz). The circuit prototype is designed in UMC 130 nm CMOS technology. The maximum value of current drawn from a DC power source of 1.2 V, at a maximum frequency of 930 MHz achieved, is 17.54 mA. After completion of the oscillator layout studied (occupied area is 165 μm x 83 μm). Measurement results confirm the expected operating range from the simulations, and therefore, that the oscillator fulfil effectively the goals initially proposed in order to be used as Local Oscillator in RF Modern Receivers

Design of an Active Harmonic Rejection N-Path Filter for Highly Tunable RF Channel Selection

As the number of wireless devices in the world increases, so does the demand for flexible radio receiver architectures capable of operating over a wide range of frequencies and communication protocols. The resonance-based channel-select filters used in traditional radio architectures have a fixed frequency response, making them poorly suited for such a receiver. The N-path filter is based on 1960s technology that has received renewed interest in recent years for its application as a linear high Q filter at radio frequencies. N-path filters use passive mixers to apply a frequency transformation to a baseband low-pass filter in order to achieve a high-Q band-pass response at high frequencies. The clock frequency determines the center frequency of the band-pass filter, which makes the filter highly tunable over a broad frequency range. Issues with harmonic transfer and poor attenuation limit the feasibility of using N-path filters in practice. The goal of this thesis is to design an integrated active N-path filter that improves upon the passive N-path filter’s poor harmonic rejection and limited outof- band attenuation. The integrated circuit (IC) is implemented using the CMRF8SF 130nm CMOS process. The design uses a multi-phase clock generation circuit to implement a harmonic rejection mixer in order to suppress the 3rd and 5th harmonic. The completed active N-path filter has a tuning range of 200MHz to 1GHz and the out-ofband attenuation exceeds 60dB throughout this range. The frequency response exhibits a 14.7dB gain at the center frequency and a -3dB bandwidth of 6.8MHz

Design analysis of levitation facility for space processing applications

Containerless processing facilities for the space laboratory and space shuttle are defined. Materials process examples representative of the most severe requirements for the facility in terms of electrical power, radio frequency equipment, and the use of an auxiliary electron beam heater were used to discuss matters having the greatest effect upon the space shuttle pallet payload interfaces and envelopes. Improved weight, volume, and efficiency estimates for the RF generating equipment were derived. Results are particularly significant because of the reduced requirements for heat rejection from electrical equipment, one of the principal envelope problems for shuttle pallet payloads. It is shown that although experiments on containerless melting of high temperature refractory materials make it desirable to consider the highest peak powers which can be made available on the pallet, total energy requirements are kept relatively low by the very fast processing times typical of containerless experiments and allows consideration of heat rejection capabilities lower than peak power demand if energy storage in system heat capacitances is considered. Batteries are considered to avoid a requirement for fuel cells capable of furnishing this brief peak power demand

Monolithic Integration Piezoelectric Resonators on CMOS for Radio-Frequency and Sensing Applications

Software cognitive radios and Internet of Things (IoT) are recent interest areas that need low loss and low power consumption hardware. More specifically, the area of software cognitive radios requires that hardware be frequency agile and highly selective. Meanwhile, IoT relies on multiple low power sensor networks. By combining Complementary Metal Oxide Semiconductors (CMOS) technology with piezoelectric Micro-Electro-Mechanical Systems (MEMS), we can fabricate Systems-on-Chip (SoC) that can be used as filters or references (oscillators) and highly selective sensors. In this work we developed a die-level compatible process for the monolithic integration of Bulk Acoustic Resonators (BAWs) on CMOS for low power, reduced area and high-quality passives for radio frequency applications. Using CMOS as a fabrication substrate some stringent requirements were added to maintain the dies and the technology’s integrity. A few of these limitations were the need for a low thermal budget fabrication process, die handling and electro-static discharge (ESD) protection. The devices were first fabricated on glass for modeling extraction that was later used for the design of the integrated circuits (IC). Three integrated circuits were designed as substrates for the integration using IBM’s 180nm and TSMC’s 65nm technology. A monolithic BAW oscillator with a resonance frequency of 1.8GHz was demonstrated with an FOM ~186dBc/Hz, comparable to other academia work. Using the developed process, a membrane BAW structure (FBAR) was integrated as well. Using a susceptor coating and zinc oxide’s (ZnO) high temperature coefficient of frequency (TCF) the device was studied as an alternative uncooled infrared sensor. Finally, a reprogrammable IC and an RF PCB were designed for volatile organic compound (VOC) testing using self-assembled monolayers (SAMs) as the absorber layer

Digital PLL for ISM applications

In modern transceivers, a low power PLL is a key block. It is known that with the evolution of technology, lower power and high performance circuitry is a challenging demand. In this thesis, a low power PLL is developed in order not to exceed 2mW of total power consumption. It is composed by small area blocks which is one of the main demands. The blocks that compose the PLL are widely abridged and the final solution is shown, showing why it is employed. The VCO block is a Current-Starved Ring Oscillator with a frequency range from 400MHz to 1.5GHz, with a 300μW to approximately 660μW power consumption. The divider is composed by six TSPC D Flip-Flop in series, forming a divide-by-64 divider. The Phase-Detector is a Dual D Flip-Flop detector with a charge pump. The PLL has less than a 2us lock time and presents a output oscillation of 1GHz, as expected. It also has a total power consumption of 1.3mW, therefore fulfilling all the specifications. The main contributions of this thesis are that this PLL can be applied in ISM applications due to its covering frequency range and low cost 130nm CMOS technology

A novel laser ranging system for measurement of ground-to-satellite distances

A technique was developed for improving the precision of laser ranging measurements of ground-to-satellite distances. The method employs a mode-locked laser transmitter and utilizes an image converter tube equipped with deflection plates in measuring the time of flight of the laser pulse to a distant retroreflector and back. Samples of the outgoing and returning light pulses are focussed on the photocathode of the image converter tube, whose deflection plates are driven by a high-voltage 120 MHz sine wave derived from a very stable oscillator. From the relative positions of the images produced at the output phosphor by the two light pulses, it is possible to make a precise determination of the fractional amount by which the time of flight exceeds some large integral multiple of the period of the deflection sinusoid

A MULTITASKING MANIPULAT ALGORITHMIC PROGRAM FOR GRID MEET UP ELECTRICAL CONVERTER IN CIRCULATED PROPAGATION DILIGENCES

This project proposes a multitasking manage algorithm for grid-linked inverters (GCIs) in distributed new release (DG) purposes. A single-phase H-bridge voltage supply inverter is exploited as a vigor digital interface between the DG procedure and the grid. The proposed manipulate algorithm produce the GCI in mongrell-appoint function manner to attain aspiration lively energy injection to the grid. Additionally to lively energy injection, the proposed manipulate algorithm has current harmonics mitigation and reactive vigor compensation capabilities for energy exceptional enhancement. The manipulate algorithm makes use of simplest the rest capacity of the GCI for best growth of energy. The proposed manage algorithm employs a current decomposition constitution headquartered on more than one adaptive interference offset filters for pulling of sympathetic and acute currents of the topical anesthetic hundreds. The pull out sympathetics are utilized in computing overcompensate currents to be shoted through the GCI

Fuel cell power conditioning multiphase converter for 1400 VDC megawatts stacks

Thesis (PhD (Electrical Engineering))--Cape Peninsula University of Technology, 2019Energy systems based on fossil fuel have demonstrated their abilities to permit economic development. However, with the fast exhaustion of this energy source, the expansion of the world energy demand and concerns over global warming, new energy systems dependent on renewable and other sustainable energy are gaining more interests. It is a fact that future development in the energy sector is founded on the utilisation of renewable and sustainable energy sources. These energy sources can enable the world to meet the double targets of diminishing greenhouse gas emissions and ensuring reliable and cost-effective energy supply. Fuel cells are one of the advanced clean energy technologies to substitute power generation systems based on fossil fuel. They are viewed as reliable and efficient technologies to operate either tied or non-tied to the grid to power applications ranging from domestic, commercial to industrial. Multiple fuel cell stacks can be associated in series and parallel to obtain a fuel cell system with high power up to megawatts. The connection of megawatts fuel cell systems to a utility grid requires that the power condition unit serving as the interface between the fuel cell plant and the grid operates accordingly. Different power conditioning unit topologies can be adopted, this study considers a multilevel inverter. Multilevel inverters are getting more popularity and attractiveness as compared to conventional inverters in high voltage and high-power applications. These inverters are suitable for harmonic mitigation in high-power applications whereby switching devices are unable to function at high switching frequencies. For a given application, the choice of appropriate multilevel topology and its control scheme are not defined and depend on various engineering compromises, however, the most developed multilevel inverter topologies include the Diode Clamped, the Flying Capacitor and the Cascade Full Bridge inverters. On the other hand, a multilevel inverter can be either a three or a five, or a nine level, however, this research focuses on the three-level diode clamped inverters. The aim of this thesis is to model and control a three-level diode clamped inverter for the grid connection of a megawatt fuel cell stack. Besides the grid, the system consists of a 1.54 MW operating at 1400 V DC proton exchange membrane fuel cell stack, a 1.26 MW three-level diode clamped inverter with a nominal voltage of 600 V and an LCL filter which is designed to reduce harmonics and meet the standards such as IEEE 519 and IEC 61000-3-6. The inverter control scheme comprises voltage and current regulators to provide a good power factor and satisfy synchronisation requirements with the grid. The frequency and phase are synchronised with those of the grid through a phase locked loop. The modelling and simulation are performed using Matlab/Simulink. The results show good performance of the developed system with a low total harmonic distortion of about 0.35% for the voltage and 0.19% for the current

Multilayer microwave structures using thick-film technology.

Multilayer techniques, in conjunction with thick-film technology have been applied to the design and fabrication of several multilayer microwave structures to achieve the low cost and high performance goals set by modern microwave circuits and systems. To provide accurate material parameters for the design of multilayer thick-film components, a novel slit cavity resonator method has been developed that enables the relative permittivity and loss tangent of dielectric samples to be measured easily, and with high accuracy. A particular feature of this method is that it can be used to measure thick-film samples that are normally only available in relatively thin layers in a two-layer format. Rigorous electromagnetic analysis on a slit cavity has been performed that accounts for the effect of the fringing fields and the radiation from the slits. The method has been verified through measurement on several thick-film materials over X-band. Both the analytical methods and the fabrication techniques for multilayer microwave microstrip structures are presented. Several multilayer thick-film microstrip line test structures have been designed and characterised, and these provide a basic database for the design of multilayer microstrip components. A new design procedure for the multilayer end-coupled filter has been developed that enables the designer to arrive at the physical dimensions of the multilayer structure based on the filter specification. This design technique is effective as it combines the accuracy of electromagnetic (EM) analysis and the efficiency of circuit simulation. The multilayer gap, which is the most critical element of multilayer end-coupled filters, has been characterised using EM analysis and the data is incorporated into a circuit simulator. Measured and simulated results are presented that verify the new design technique. A 40% bandwidth has been achieved experimentally, which shows a very significant improvement over conventional single layer structures, where the bandwidth achievable is normally less than 5%. Novel, octave band DC blocks have been designed, fabricated and tested using a new multilayer format. The tight coupling required between the coupled lines in this component was realized by overlapping these lines in a multilayer structure. Very good agreement was obtained between measured and simulated data. The multilayer approach was also applied to the design of coupled line bandpass filters where a measured 80% bandwidth was achieved. For the first time, the properties of multilayer coupled lines using a range of different thick-film dielectrics are examined using their coupled-mode parameters. Design curves for multilayer coupled lines are obtained, that provide important information on the design of multilayer directional couplers. A practical design strategy for multilayer directional couplers is developed, which overcomes the problem of excessive computation that is normally associated with the electromagnetic optimization of multilayer circuit designs. The methodology has been verified through the design and measurement of wide bandwidth 2dB and 3dB directional couplers that were fabricated using multilayer, thick-film technology. New techniques for the design and fabrication of multilayer microwave thick-film components have thus been established, both theoretically and through practical circuit fabrication and measurement