Regularized lattice Boltzmann Multicomponent models for low Capillary and Reynolds microfluidics flows

We present a regularized version of the color gradient lattice Boltzmann (LB) scheme for the simulation of droplet formation in microfluidic devices of experimental relevance. The regularized version is shown to provide computationally efficient access to Capillary number regimes relevant to droplet generation via microfluidic devices, such as flow-focusers and the more recent microfluidic step emulsifier devices.Comment: 9 pages, 5 figure

Design and fabrication of chemically robust three-dimensional microfluidic valves

A current problem in microfluidics is that poly(dimethylsiloxane) (PDMS), used to fabricate many microfluidic devices, is not compatible with most organic solvents. Fluorinated compounds are more chemically robust than PDMS but, historically, it has been nearly impossible to construct valves out of them by multilayer soft lithography (MSL) due to the difficulty of bonding layers made of non-stick fluoropolymers necessary to create traditional microfluidic valves. With our new three-dimensional (3D) valve design we can fabricate microfluidic devices from fluorinated compounds in a single monolithic layer that is resistant to most organic solvents with minimal swelling. This paper describes the design and development of 3D microfluidic valves by molding of a perfluoropolyether, termed Sifel, onto printed wax molds. The fabrication of Sifel-based microfluidic devices using this technique has great potential in chemical synthesis and analysis

Design automation based on fluid dynamics

This article was accepted and presented at the 9th International Workshop on Bio-Design Automation, Pittsburgh, Pennsylvania (2017).Microfluidic devices provide researchers with numerous advantages such as high throughput, increased sensitivity and accuracy, lower cost, and reduced reaction time. However, design, fabrication, and running a microfluidic device are still heavily reliant on expertise. Recent studies suggest micro-milling can be a semi-automatic, inexpensive, and simple alternative to common fabrication methods. Micro-milling does not require a clean-room, mask aligner, spin-coater, and Plasma bonder, thus cutting down the cost and time of fabrication significantly. Moreover, through this protocol researchers can easily fabricate microfluidic devices in an automated fashion eschewing levels of expertise required for typical fabrication methods, such as photolithography, soft-lithography, and etching. However, designing a microfluidic chip that meets a certain set of requirements is still heavily dependent on a microfluidic expert, several days of simulation, and numerous experiments to reach the required performance. To address this, studies have reported random automated design of microfluidic devices based on numerical simulations for micro-mixing. However, random design generation is heavily reliant on time-consuming simulations carried out beforehand, and is prone to error due to the accuracy limitations of the numerical method. On the other hand, by using micro-milling for ultra-fast and inexpensive fabrication of microfluidic devices and Taguchi design of experiments for state-space exploration of all of the geometric parameters, we are able to generate a database of geometries, flow rates, and flow properties required for a single primitive to carry out a specified microfluidic task

A Microfluidic Platform for Precision Small-volume Sample Processing and Its Use to Size Separate Biological Particles with an Acoustic Microdevice.

A major advantage of microfluidic devices is the ability to manipulate small sample volumes, thus reducing reagent waste and preserving precious sample. However, to achieve robust sample manipulation it is necessary to address device integration with the macroscale environment. To realize repeatable, sensitive particle separation with microfluidic devices, this protocol presents a complete automated and integrated microfluidic platform that enables precise processing of 0.15-1.5 ml samples using microfluidic devices. Important aspects of this system include modular device layout and robust fixtures resulting in reliable and flexible world to chip connections, and fully-automated fluid handling which accomplishes closed-loop sample collection, system cleaning and priming steps to ensure repeatable operation. Different microfluidic devices can be used interchangeably with this architecture. Here we incorporate an acoustofluidic device, detail its characterization, performance optimization, and demonstrate its use for size-separation of biological samples. By using real-time feedback during separation experiments, sample collection is optimized to conserve and concentrate sample. Although requiring the integration of multiple pieces of equipment, advantages of this architecture include the ability to process unknown samples with no additional system optimization, ease of device replacement, and precise, robust sample processing

Simplified immobilisation method for histidine-tagged enzymes in poly(methyl methacrylate) microfluidic devices

Article in press. Kulsharova, G., New BIOTECHNOLOGY (2017), https://doi.org/10.1016/j.nbt.2017.12.004Poly(methyl methacrylate) (PMMA) microfluidic devices have become promising platforms for a wide range of applications. Here we report a simple method for immobilising histidine-tagged enzymes suitable for PMMA microfluidic devices. The 1-step-immobilisation described is based on the affinity of the His-tag/Ni-NTA interaction and does not require prior amination of the PMMA surface, unlike many existing protocols. We compared it with a 3-step immobilisation protocol involving amination of PMMA and linking NTA via a glutaraldehyde cross-linker. These methods were applied to immobilise transketolase (TK) in PMMA microfluidic devices. Binding efficiency studies showed that about 15% of the supplied TK was bound using the 1-step method and about 26% of the enzyme was bound by the 3-step method. However, the TK-catalysed reaction producing l-erythrulose performed in microfluidic devices showed that specific activity of TK in the device utilising the 1-step immobilisation method was approximately 30% higher than that of its counterpart. Reusability of the microfluidic device produced via the 1-step method was tested for three cycles of enzymatic reaction and at least 85% of the initial productivity was maintained. The device could be operated for up to 40 h in a continuous flow and on average 70% of the initial productivity was maintained. The simplified immobilisation method required fewer chemicals and less time for preparation of the immobilised microfluidic device compared to the 3-step method while achieving higher specific enzyme activity. The method represents a promising approach for the development of immobilised enzymatic microfluidic devices and could potentially be applied to combine protein purification with immobilisation.Peer reviewe

Microfluidic DNA amplification - a review

The application of microfluidic devices for DNA amplification has recently been extensively studied. Here, we review the important development of microfluidic polymerase chain reaction (PCR) devices and discuss the underlying physical principles for the optimal design and operation of the device. In particular, we focus on continuous-flow microfluidic PCR on-chip, which can be readily implemented as an integrated function of a micro-total-analysis system. To overcome sample carryover contamination and surface adsorption associated with microfluidic PCR, microdroplet technology has recently been utilized to perform PCR in droplets, which can eliminate the synthesis of short chimeric products, shorten thermal-cycling time, and offers great potential for single DNA molecule and single-cell amplification. The work on chip-based PCR in droplets is highlighted

Ultrafast High-pressure AC Electro-osmotic Pumps for Portable Biomedical Microfluidics

This paper details the development of an integrated AC electro-osmotic (ACEO) microfluidic pump for dilute electrolytes consisting of a long serpentine microchannel lined with three dimensional (3D) stepped electrode arrays. Using low AC voltage (1 Volt rms, 1 kHz), power (5 mW) and current (3.5 mA) in water, the pump is capable of generating a 1.4 kPa head pressure, a 100-fold increase over prior ACEO pumps, and a 1.37 mm/sec effective slip velocity over the electrodes without flow reversal. The integrated ACEO pump can utilize low ionic strength solutions such as distilled water as the working solution to pump physiological strength (100 mM) biological solutions in separate microfluidic devices, with potential applications in portable or implantable biomedical microfluidic devices. As a proof-of-concept experiment, the use of the ACEO pumps for DNA hybridization in a microfluidic microarray is demonstrated

Directed Placement for mVLSI Devices

Continuous-flow microfluidic devices based on integrated channel networks are becoming increasingly prevalent in research in the biological sciences. At present, these devices are physically laid out by hand by domain experts who understand both the underlying technology and the biological functions that will execute on fabricated devices. The lack of a design science that is specific to microfluidic technology creates a substantial barrier to entry. To address this concern, this article introduces Directed Placement, a physical design algorithm that leverages the natural "directedness" in most modern microfluidic designs: fluid enters at designated inputs, flows through a linear or tree-based network of channels and fluidic components, and exits the device at dedicated outputs. Directed placement creates physical layouts that share many principle similarities to those created by domain experts. Directed placement allows components to be placed closer to their neighbors compared to existing layout algorithms based on planar graph embedding or simulated annealing, leading to an average reduction in laid-out fluid channel length of 91% while improving area utilization by 8% on average. Directed placement is compatible with both passive and active microfluidic devices and is compatible with a variety of mainstream manufacturing technologies

Elastomeric microfluidic diode and rectifier work with Newtonian fluids

We report on two microfluidic elastomeric autoregulatory devices—a diode and a rectifier. They exhibit physically interesting and complex nonlinear behaviors (saturation, bias-dependent resistance, and rectification) with a Newtonian fluid. Due to their autoregulatory properties, they operate without active external control. As a result, they enable increased microfluidic device density and overall system miniaturization. The demonstrated diode and rectifier would also be useful components in future microfluidic logic circuitry