Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

Multilevel Clustering Fault Model for IC Manufacture

A hierarchical approach to the construction of compound distributions for process-induced faults in IC manufacture is proposed. Within this framework, the negative binomial distribution is treated as level-1 models. The hierarchical approach to fault distribution offers an integrated picture of how fault density varies from region to region within a wafer, from wafer to wafer within a batch, and so on. A theory of compound-distribution hierarchies is developed by means of generating functions. A study of correlations, which naturally appears in microelectronics due to the batch character of IC manufacture, is proposed. Taking these correlations into account is of significant importance for developing procedures for statistical quality control in IC manufacture. With respect to applications, hierarchies of yield means and yield probability-density functions are considered.Comment: 10 pages, the International Conference "Micro- and Nanoelectronics- 2003" (ICMNE-2003),Zvenigorod, Moscow district, Russia, October 6-10, 200

Parametric Yield of VLSI Systems under Variability: Analysis and Design Solutions

Variability has become one of the vital challenges that the designers of integrated circuits encounter. variability becomes increasingly important. Imperfect manufacturing process manifest itself as variations in the design parameters. These variations and those in the operating environment of VLSI circuits result in unexpected changes in the timing, power, and reliability of the circuits. With scaling transistor dimensions, process and environmental variations become significantly important in the modern VLSI design. A smaller feature size means that the physical characteristics of a device are more prone to these unaccounted-for changes. To achieve a robust design, the random and systematic fluctuations in the manufacturing process and the variations in the environmental parameters should be analyzed and the impact on the parametric yield should be addressed. This thesis studies the challenges and comprises solutions for designing robust VLSI systems in the presence of variations. Initially, to get some insight into the system design under variability, the parametric yield is examined for a small circuit. Understanding the impact of variations on the yield at the circuit level is vital to accurately estimate and optimize the yield at the system granularity. Motivated by the observations and results, found at the circuit level, statistical analyses are performed, and solutions are proposed, at the system level of abstraction, to reduce the impact of the variations and increase the parametric yield. At the circuit level, the impact of the supply and threshold voltage variations on the parametric yield is discussed. Here, a design centering methodology is proposed to maximize the parametric yield and optimize the power-performance trade-off under variations. In addition, the scaling trend in the yield loss is studied. Also, some considerations for design centering in the current and future CMOS technologies are explored. The investigation, at the circuit level, suggests that the operating temperature significantly affects the parametric yield. In addition, the yield is very sensitive to the magnitude of the variations in supply and threshold voltage. Therefore, the spatial variations in process and environmental variations make it necessary to analyze the yield at a higher granularity. Here, temperature and voltage variations are mapped across the chip to accurately estimate the yield loss at the system level. At the system level, initially the impact of process-induced temperature variations on the power grid design is analyzed. Also, an efficient verification method is provided that ensures the robustness of the power grid in the presence of variations. Then, a statistical analysis of the timing yield is conducted, by taking into account both the process and environmental variations. By considering the statistical profile of the temperature and supply voltage, the process variations are mapped to the delay variations across a die. This ensures an accurate estimation of the timing yield. In addition, a method is proposed to accurately estimate the power yield considering process-induced temperature and supply voltage variations. This helps check the robustness of the circuits early in the design process. Lastly, design solutions are presented to reduce the power consumption and increase the timing yield under the variations. In the first solution, a guideline for floorplaning optimization in the presence of temperature variations is offered. Non-uniformity in the thermal profiles of integrated circuits is an issue that impacts the parametric yield and threatens chip reliability. Therefore, the correlation between the total power consumption and the temperature variations across a chip is examined. As a result, floorplanning guidelines are proposed that uses the correlation to efficiently optimize the chip's total power and takes into account the thermal uniformity. The second design solution provides an optimization methodology for assigning the power supply pads across the chip for maximizing the timing yield. A mixed-integer nonlinear programming (MINLP) optimization problem, subject to voltage drop and current constraint, is efficiently solved to find the optimum number and location of the pads

Custom Integrated Circuits

Contains reports on six research projects.U.S. Air Force - Office of Scientific Research (Grant AFOSR-86-0164)U.S. Navy - Office of Naval Research (Contract N00014-80-C-0622)National Science Foundation (Grant ECS-83-10941

Benchmark methodologies for the optimized physical synthesis of RISC-V microprocessors

As technology continues to advance and chip sizes shrink, the complexity and design time required for integrated circuits have significantly increased. To address these challenges, Electronic Design Automation (EDA) tools have been introduced to streamline the design flow. These tools offer various methodologies and options to optimize power, performance, and chip area. However, selecting the most suitable methods from these options can be challenging, as they may lead to trade-offs among power, performance, and area. While architectural and Register Transfer Level (RTL) optimizations have been extensively studied in existing literature, the impact of optimization methods available in EDA tools on performance has not been thoroughly researched. This thesis aims to optimize a semiconductor processor through EDA tools within the physical synthesis domain to achieve increased performance while maintaining a balance between power efficiency and area utilization. By leveraging floorplanning tools and carefully selecting technology libraries and optimization options, the CV32E40P open-source processor is subjected to various floorplans to analyze their impact on chip performance. The employed techniques, including multibit components prefer option, multiplexer tree prefer option, identification and exclusion of problematic cells, and placement blockages, lead to significant improvements in cell density, congestion mitigation, and timing. The optimized synthesis results demonstrate a 71\% enhancement in chip design performance without a substantial increase in area, showcasing the effectiveness of these techniques in improving large-scale integrated circuits' performance, efficiency, and manufacturability. By exploring and implementing the available options in EDA tools, this study demonstrates how the processor's performance can be significantly improved while maintaining a balanced and efficient chip design. The findings contribute valuable insights to the field of electronic design automation, offering guidance to designers in selecting suitable methodologies for optimizing processors and other integrated circuits

Enhancing Power Efficient Design Techniques in Deep Submicron Era

Excessive power dissipation has been one of the major bottlenecks for design and manufacture in the past couple of decades. Power efficient design has become more and more challenging when technology scales down to the deep submicron era that features the dominance of leakage, the manufacture variation, the on-chip temperature variation and higher reliability requirements, among others. Most of the computer aided design (CAD) tools and algorithms currently used in industry were developed in the pre deep submicron era and did not consider the new features explicitly and adequately. Recent research advances in deep submicron design, such as the mechanisms of leakage, the source and characterization of manufacture variation, the cause and models of on-chip temperature variation, provide us the opportunity to incorporate these important issues in power efficient design. We explore this opportunity in this dissertation by demonstrating that significant power reduction can be achieved with only minor modification to the existing CAD tools and algorithms. First, we consider peak current, which has become critical for circuit's reliability in deep submicron design. Traditional low power design techniques focus on the reduction of average power. We propose to reduce peak current while keeping the overhead on average power as small as possible. Second, dual Vt technique and gate sizing have been used simultaneously for leakage savings. However, this approach becomes less effective in deep submicron design. We propose to use the newly developed process-induced mechanical stress to enhance its performance. Finally, in deep submicron design, the impact of on-chip temperature variation on leakage and performance becomes more and more significant. We propose a temperature-aware dual Vt approach to alleviate hot spots and achieve further leakage reduction. We also consider this leakage-temperature dependency in the dynamic voltage scaling approach and discover that a commonly accepted result is incorrect for the current technology. We conduct extensive experiments with popular design benchmarks, using the latest industry CAD tools and design libraries. The results show that our proposed enhancements are promising in power saving and are practical to solve the low power design challenges in deep submicron era