Projection-based measurement and identification

A recently developed Projection-based Digital Image Correlation (P-DVC) method is here extended to 4D (space and time) displacement field measurement and mechanical identification based on a single radiograph per loading step instead of volumes as in standard DVC methods. Two levels of data reductions are exploited, namely, reduction of the data acquisition (and time) by a factor of 1000 and reduction of the solution space by exploiting model reduction techniques. The analysis of a complete tensile elastoplastic test composed of 127 loading steps performed in 6 minutes is presented. The 4D displacement field as well as the elastoplastic constitutive law are identified. Keywords: Image-based identification, Model reduction, Fast 4D identification, In-situ tomography measurements. INTRODUCTION Identification and validation of increasingly complex mechanical models is a major concern in experimental solid mechanics. The recent developments of computed tomography coupled with in-situ tests provide extremely rich and non-destructive analyses [1]. In the latter cases, the sample was imaged inside a tomograph, either with interrupted mechanical load or with a continuously evolving loading and on-the-fly acquisitions (as ultra-fast X-ray synchrotron tomography, namely, 20 Hz full scan acquisition for the study of crack propagation [2]). Visualization of fast transformations, crack openings, or unsteady behavior become accessible. Combined with full-field measurements, in-situ tests offer a quantitative basis for identifying a broad range of mechanical behavior.Comment: SEM 2019, Jun 2019, Reno, United State

In situ fatigue loading stage inside scanning electron microscope

A fatigue loading stage inside a scanning electron microscopy (SEM) was developed. The stage allows dynamic and static high-magnification and high-resolution viewing of the fatigue crack initiation and crack propagation processes. The loading stage is controlled by a closed-loop servohydraulic system. Maximum load is 1000 lb (4450 N) with test frequencies ranging up to 30 Hz. The stage accommodates specimens up to 2 inches (50 mm) in length and tolerates substantial specimen translation to view the propagating crack. At room temperature, acceptable working resolution is obtainable for magnifications ranging up to 10,000X. The system is equipped with a high-temperature setup designed for temperatures up to 2000 F (1100 C). The signal can be videotaped for further analysis of the pertinent fatigue damage mechanisms. The design allows for quick and easy interchange and conversion of the SEM from a loading stage configuration to its normal operational configuration and vice versa. Tests are performed entirely in the in-situ mode. In contrast to other designs, the NASA design has greatly extended the life of the loading stage by not exposing the bellows to cyclic loading. The loading stage was used to investigate the fatigue crack growth mechanisms in the (100)-oriented PWA 1480 single-crystal, nickel-based supperalloy. The high-magnification observations revealed the details of the crack growth processes

Cryogenic Stress-Driven Grain Growth Observed via Microcompression with in situ Electron Backscatter Diffraction

The deformation of materials at cryogenic temperature is of interest for space, arctic, and fundamental science applications. In this work, a custom-built cooling system attached to a commercial picoindenter was used for in situ cryogenic microcompression testing of equal-channel angular-pressed copper with real-time electron backscatter diffraction. Stress-driven grain growth at cryogenic temperatures was observed during a series of elastic and plastic deformations. These results provide direct evidence for the previously predicted phenomenon, whereas previous ex situ examinations demonstrated coarsening after cryogenic loading when samples were not maintained at cryogenic temperatures between deformation and characterization

A portable load cell for in-situ ore impact breakage testing

This paper discusses the design and characterisation of a short, and hence portable impact load cell for in-situ quantification of ore breakage properties under impact loading conditions. Much literature has been published in the past two decades about impact load cells for ore breakage testing. It has been conclusively shown that such machines yield significant quantitative energy-fragmentation information about industrial ores. However, documented load cells are all laboratory systems that are not adapted for in-situ testing due to their dimensions and operating requirements. The authors report on a new portable impact load cell designed specifically for in-situ testing. The load cell is 1.5 m in height and weighs 30 kg. Its physical and operating characteristics are detailed in the paper. This includes physical dimensions, calibration and signal deconvolution. Emphasis is placed on the deconvolution issue, which is significant for such a short load cell. Finally, it is conclusively shown that the short load cell is quantitatively as accurate as its larger laboratory analogues

Novel Ferromagnetic Atom Waveguide with in situ loading

Magneto-optic and magnetostatic trapping is realized near a surface using current carrying coils wrapped around magnetizable cores. A cloud of 10^7 Cesium atoms is created with currents less than 50 mA. Ramping up the current while maintaining optical dissipation leads to tightly confined atom clouds with an aspect ratio of 1:1000. We study the 3D character of the magnetic potential and characterize atom number and density as a function of the applied current. The field gradient in the transverse dimension has been varied from < 10 G/cm to > 1 kG/cm. By loading and cooling atoms in-situ, we have eliminated the problem of coupling from a MOT into a smaller phase space.Comment: 4 pages, 4 figure

Non-destructive evaluation of cement-based materials from pressure-stimulated electrical emission - Preliminary results

This is the post-print version of the final paper published in Construction and Building Materials. The published article is available from the link below. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. Copyright @ 2010 Elsevier B.V.This paper introduces the possibility of in situ assessment of loading and remaining strength in concrete structures by means of measuring discharge of electric current from loaded specimens. The paper demonstrates that the techniques have been applied to other rock-like materials, but that for the first time they are applied to cement-based materials and a theoretical model is proposed in relation to the appearance of electrical signals during sample loading and up to fracture. A series of laboratory experiments on cement mortar specimens in simple uniaxial compression, and subsequently in bending – hence displaying both tension and compression – are described and show clear correlations between resulting strains and currents measured. Under uniaxial loading there is a well-defined relationship between the pressure-stimulated current (PSC) as a result of a monotonic mechanical loading regime. Similar results are observed in the three-point bending tests where a range of loading regimes is studied, including stepped changes in loading. While currents can be measured at low strains, best results seem to be obtained when strains approach and exceed yield stress values. This technique clearly has immense potential for structural health monitoring of cement-based structures. Both intermittent and continuous monitoring becomes possible, and given an ongoing campaign of monitoring, remaining strength can be estimated

Gas gun shock experiments with single-pulse x-ray phase contrast imaging and diffraction at the Advanced Photon Source

The highly transient nature of shock loading and pronounced microstructure effects on dynamic materials response call for {\it in situ}, temporally and spatially resolved, x-ray-based diagnostics. Third-generation synchrotron x-ray sources are advantageous for x-ray phase contrast imaging (PCI) and diffraction under dynamic loading, due to their high photon energy, high photon fluxes, high coherency, and high pulse repetition rates. The feasibility of bulk-scale gas gun shock experiments with dynamic x-ray PCI and diffraction measurements was investigated at the beamline 32ID-B of the Advanced Photon Source. The x-ray beam characteristics, experimental setup, x-ray diagnostics, and static and dynamic test results are described. We demonstrate ultrafast, multiframe, single-pulse PCI measurements with unprecedented temporal ($<$100 ps) and spatial ($\sim$2 $\mu$m) resolutions for bulk-scale shock experiments, as well as single-pulse dynamic Laue diffraction. The results not only substantiate the potential of synchrotron-based experiments for addressing a variety of shock physics problems, but also allow us to identify the technical challenges related to image detection, x-ray source, and dynamic loading

Direct Formation of Structural Components Using a Martian Soil Simulant.

Martian habitats are ideally constructed using only locally available soils; extant attempts to process structural materials on Mars, however, generally require additives or calcination. In this work we demonstrate that Martian soil simulant Mars-1a can be directly compressed at ambient into a strong solid without additives, highlighting a possible aspect of complete Martian in-situ resource utilization. Flexural strength of the compact is not only determined by the compaction pressure but also significantly influenced by the lateral boundary condition of processing loading. The compression loading can be applied either quasi-statically or through impact. Nanoparticulate iron oxide (npOx), commonly detected in Martian regolith, is identified as the bonding agent. Gas permeability of compacted samples was measured to be on the order of 10-16 m2, close to that of solid rocks. The compaction procedure is adaptive to additive manufacturing

Autumn Storms Trigger Enhanced Export of Iron, Phosphorus, and Carbon from a Forested Vermont Catchment

Autumn leaf fall may be an important driver of annual stream loading in forested catchments due to the introduction of large amounts of labile organic matter. In light of climate change projections for an intensification of the autumnal hydrological cycle for northern temperate forests, there is an increasing demand to understand this leaf fall period, and the extent to which it may drive water quality. In this study, we examine the export and biogeochemical coupling of dissolved organic carbon (DOC), iron (Fe), aluminum (Al), and phosphorus (P) during autumn and summer storms to understand the effects of seasonality and storm timing and magnitude on stream loading dynamics. We utilize in situ spectrophotometric sensors to measure UV-Vis light absorbance with high temporal resolution in order to quantify rapid changes in stream chemistry during storm events. We also explore the potential to project concentrations of the aforementioned parameters using partial least squares regression (PLSR) and high frequency absorbance data. Post leaf fall autumn storms resulted in the export of 23% of total study DOC in a 2-week period, as well as the largest fluxes of Fe and Al observed over the study period. These results may have important implications for nutrient loading in the receiving water body, Lake Champlain