Quantum spectroscopy of plasmonic nanostructures

We use frequency entangled photons, generated via spontaneous parametric down conversion, to measure the broadband spectral response of an array of gold nanoparticles exhibiting Fano-type plasmon resonance. Refractive index sensing of a liquid is performed by measuring the shift of the array resonance. This method is robust in excessively noisy conditions compared with conventional broadband transmission spectroscopy. Detection of a refractive index change is demonstrated with a noise level 70 times higher than the signal, which is shown to be inaccessible with the conventional transmission spectroscopy. Use of low photon fluxes makes this method suitable for measurements of photosensitive bio-samples and chemical substances.Comment: 11 pages, 5 figure

Analysis of 3D-printed metal for rapid-prototyped reflective terahertz optics

We explore the potential of 3D metal printing to realize complex conductive terahertz devices. Factors impacting performance such as printing resolution, surface roughness, oxidation, and material loss are investigated via analytical, numerical, and experimental approaches. The high degree of control offered by a 3D-printed topology is exploited to realize a zone plate operating at 530 GHz. Reflection efficiency at this frequency is found to be over 90%. The high-performance of this preliminary device suggest that 3D metal printing can play a strong role in guided-wave and general beam control devices in the terahertz range.Comment: 13 pages, 6 figures, submitted to Optics Expres

Enhancing the fill-factor of CMOS SPAD arrays using microlens integration

Arrays of single-photon avalanche diode (SPAD) detectors were fabricated, using a 0.35 μm CMOS technology process, for use in applications such as time-of-flight 3D ranging and microscopy. Each 150 x 150 μm pixel comprises a 30 μm active area diameter SPAD and its associated circuitry for counting, timing and quenching, resulting in a fill-factor of 3.14%. This paper reports how a higher effective fill-factor was achieved as a result of integrating microlens arrays on top of the 32 x 32 SPAD arrays. Diffractive and refractive microlens arrays were designed to concentrate the incoming light onto the active area of each pixel. A telecentric imaging system was used to measure the improvement factor (IF) resulting from microlens integration, whilst varying the f-number of incident light from f/2 to f/22 in one-stop increments across a spectral range of 500-900 nm. These measurements have demonstrated an increasing IF with fnumber, and a maximum of ~16 at the peak wavelength, showing a good agreement with theoretical values. An IF of 16 represents the highest value reported in the literature for microlenses integrated onto a SPAD detector array. The results from statistical analysis indicated the variation of detector efficiency was between 3-10% across the whole f-number range, demonstrating excellent uniformity across the detector plane with and without microlenses

Femtosecond Laser Written Volumetric Diffractive Optical Elements And Their Applications

Since the first demonstration of femtosecond laser written waveguides in 1996, femtosecond laser direct writing (FLDW) has been providing a versatile means to fabricate embedded 3-D microstructures in transparent materials. The key mechanisms are nonlinear absorption processes that occur when a laser beam is tightly focused into a material and the intensity of the focused beam reaches the range creating enough free electrons to induce structural modification. One of the most useful features that can be exploited in fabricating photonic structures is the refractive index change which results from the localized energy deposition. The laser processing system for FLDW can be realized as a compact, desktop station, implemented by a laser source, a 3-D stage and focusing optics. Thus, FLDW can be readily adopted for the fabrication of the photonic devices. For instance, it has been widely employed in various areas of photonic device fabrication such as active and passive waveguides, couplers, gratings, opto-fluidics and similar applications. This dissertation describes the use of FLDW towards the fabrication of custom designed diffractive optical elements (DOE’s). These are important micro-optical elements that are building blocks in integrated optical devices including on-chip sensors and systems. The fabrication and characterization of laser direct written DOEs in different glass materials is investigated. The design and performance of a range of DOE’s is described, especially, laser-written embedded Fresnel zone plates and linear gratings. Their diffractive efficiency as a function of the fabrication parameters is discussed and an optimized fabrication process is realized. The potential of the micro-DOEs and their integration shown in this dissertation will impact on the fabrication of future on-chip devices involving customized iv DOEs that will serve great flexibility and multi-functional capability on sensing, imaging and beam shaping

Miniaturization of optical spectrometers

Spectroscopic analysis is one of the most widely used analytical tools across both scientific research and industry. Whilst laboratory bench-top spectrometer systems offer superlative resolution and spectral range, their miniaturization is crucial for applications where portability is paramount, or in-situ measurements must be made. Advancement in this field over the last three decades is now yielding microspectrometers with performance and footprint near those viable for lab-on-a-chip systems, smartphones and other consumer technologies. In this review, we briefly summarize the technologies that have emerged toward achieving these aims - including miniaturized dispersive optics, narrowband filter systems, Fourier transform interferometers and reconstructive microspectrometers - and discuss the challenges associated with improving spectral resolution while device dimensions shrink ever further.EPSRC: EP/L016087/1 National Natural Science Foundation of China (51706141, 51976122

Infrared Energy Harvesting for Optoplasmonics from Nanostructured Metamaterials

Metamaterials exhibit unique optical resonance characteristics which permit precise engineering of energy pathways within a device. The ability of plasmonic nanostructures to guide electromagnetism offers a platform to reduce global dependence on fossil fuels by harvesting waste heat, which comprises 60% of generated energy around the world. Plasmonic metamaterials were hypothesized to support an exchange of energy between resonance modes, enabling generation of higher energy photons from waste infrared energy. Infrared irradiation of a metamaterial at the Fano coupling lattice resonance was anticipated to re-emit as higher energy visible light at the plasmon resonance. Photonic signals from harvested thermal energy could be used to power wearable medical monitors or off-grid excursions, for example. This thesis developed the design, fabrication, and characterization methods to realize nanostructured metamaterials which permit resonance exchange for infrared energy harvesting applications